Thin-Wall Pipeline Repair: Evaluation of Reinforcement Systems and Internal Temperature Monitoring During Maintenance Procedures

2018 ◽  
Author(s):  
Colton Sheets ◽  
Taylor Shie ◽  
Adam Crawford
Keyword(s):  
Type A ◽  
Inside Surface ◽  
Repair System ◽  
Thin Wall ◽  
Type B ◽  
Pipe Surface ◽  
Wall Loss ◽  
Maintenance Activities ◽  
Repair Systems ◽  
Steel Sleeve

There are many options available to pipeline operators when addressing anomalies or integrity threats. Repairing integrity threats requires an understanding of both the anomaly to be repaired, and the repair system itself. This can be challenging as pipeline repair systems come in a wide variety of materials, application techniques, and designs. Operators have similar challenges when performing maintenance activities on operating pipelines. Maintenance activities can take many different forms and often involve welding or other high temperature processes on the outside pipe surface. These processes can result in elevated temperatures on the inside surface of the pipeline and must be seriously considered before undertaking to ensure the safety of personnel performing the tasks and to protect the integrity of the pipeline. This study aimed to provide a greater understanding of pipeline reinforcement systems and maintenance activities as they relate specifically to thin-walled pipelines. To evaluate systems reinforcing thin-wall pipes, five different repair systems were investigated using 12.75-inch × 0.219-inch, Gr. X65 pipe that had been removed from service. The systems included a Type B steel sleeve, an epoxy-filled, interference fit, Type A steel sleeve, a hybrid steel sleeve-fiberglass based composite repair system, epoxy-filled oversized Type A steel sleeves, and a rigid coil, pre-cured, fiberglass-based composite repair system. Each system was used to reinforce a simulated 50% wall loss anomaly and was installed with the pipe samples maintained at an internal pressure equal to 33% of the pipe’s specified minimum yield strength (SMYS). The samples underwent pressure cycling and hydrostatic testing while strains in the simulated wall loss region were continually monitored. As a final step, the samples were burst tested. Monitoring of strain gages installed in the simulated wall loss anomaly allowed for comparisons to be made between the tested repair systems. It was observed that the recorded strain magnitudes and strain ranges were higher in some samples than others during testing. This allowed the systems to be ranked according to the recorded strains. Although differences were observed in the recorded strains, burst testing showed that all reinforcement systems were able to force failure to the base pipe outside of the simulated wall loss region. Maintenance procedures were also evaluated to identify those that could produce unacceptable temperatures on the inside surface of the thin-wall pipe. The maintenance procedures included installation of Type A steel sleeves (non-pressure containing), Type B steel sleeves (pressure containing), cad welds, and pin brazing cathodic protection (CP) test leads. Temperatures were monitored on the internal pipe surface using thermocouples and an infrared (IR) camera while the maintenance procedures were being performed. An internal surface temperature of 500 °F (260 °C) was set as the threshold for suitability. Monitoring of the Type B steel sleeve installation showed temperatures on the inside surface of the pipe that exceeded 1,200 °F (648 °C) when performing the circumferential weld at each end of the steel sleeve. A maximum temperature of 280 °F (137 °C) was recorded when making the longitudinal welds that included a backing strip. For the application being considered, this indicated that Type A steel sleeves (longitudinal welds only) could be installed within the required temperature limits. A maximum internal temperature of 936 °F (502 °C) was recorded during cad-welding. Pin-brazing was slightly lower, but also exceeded the 500 °F threshold. This testing confirmed that the installation of Type B steel sleeves, cad welding, or pin brazing should receive scrutiny before being performed on operating thin-wall pipelines.

Biological and Morphological Studies on Low-Leukemia-Strain Mice with Hodgkin's-Like Neoplasia Induced by Serial Cell-Free Transmission of Leukemic Organs of SJL/J Strain Mice

1968 ◽  
Vol 26 ◽  
pp. 210-211
Author(s):  
S. Fujinaga ◽  
K. Maruyama ◽  
C.W. Williams ◽  
K. Sekhri ◽  
L. Dmochowski
Keyword(s):  
Tissue Culture ◽  
Type A ◽  
Reticulum Cell ◽  
Type B ◽  
Viral Origin ◽  
Serial Transfer ◽  
Strain Mouse ◽  
Morphological Studies ◽  
Cell Neoplasm ◽  
Free Material

Yumoto and Dmochowski (Cancer Res.27, 2098 (1967)) reported the presence of mature and immature type C leukemia virus particles in leukemic organs and tissues such as lymph nodes, spleen, thymus, liver, and kidneys of SJL/J strain mice with Hodgki's-like disease or reticulum cell neoplasm (type B). In an attempt to ascertain the possibility that this neoplasia may be of viral origin, experiments with induction and transmission of this neoplasm were carried out using cell-free extracts of leukemic organs from an SJL/J strain mouse with spontaneous disease.It has been possible to induce the disease in low-leukemia BALB/c and C3HZB strain mice and serially transfer the neoplasia by cell-free extracts of leukemic organs of these mice. Histological examination revealed the neoplasia to be of either reticulum cell-type A or type B. Serial transfer is now in its fifth passage. In addition leukemic spleen from another SJL/J strain mouse with spontaneous reticulum cell neoplasm (type A) was set up in tissue culture and is now in its 141st serial passage in vitro. Preliminary results indicate that cell-free material of 39th tissue culture passage can reproduce neoplasia in BALB/c mice.

Anticoagulant Activity of β2-Glycoprotein I Is Potentiated by a Distinct Subgroup of Anticardiolipin Antibodies

1992 ◽  
Vol 68 (03) ◽  
pp. 297-300 ◽  
Author(s):  
Monica Galli ◽  
Paul Comfurius ◽  
Tiziano Barbui ◽  
Robert F A Zwaal ◽  
Edouard M Bevers
Keyword(s):  
Human Plasma ◽  
Anticoagulant Activity ◽  
Factor Xa ◽  
Type A ◽  
Lipid Vesicles ◽  
Dependent Manner ◽  
Type B ◽  
Distinct Subgroup ◽  
Glycoprotein I ◽  
Thrombin Formation

SummaryPlasmas of 16 patients positive for both IgG anticardiolipin (aCL) antibodies and lupus anticoagulant (LA) antibodies were subjected to adsorption with liposomes containing cardiolipin. In 5 of these plasmas both the anticardiolipin and the anticoagulant activities were co-sedimented with the liposomes in a dose-dependent manner, whereas in the remaining cases only the anticardiolipin activity could be removed by the liposomes, leaving the anticoagulant activity (LA) in the supernatant plasma. aCL antibodies purified from the first 5 plasmas were defined as aCL-type A, while the term aCL-type B was used for antibodies in the other 11 plasmas, from which 2 were selected for this study.Prolongation of the dRVVT was produced by affinity-purified aCL-type A antibodies in plasma of human as well as animal (bovine, rat and goat) origin. aCL-type B antibodies were found to be devoid of anticoagulant activity, while the corresponding supernatants containing LA IgG produced prolongation of the dRVVT only in human plasma.These anticoagulant activities of aCL-type A and of LA IgG's were subsequently evaluated in human plasma depleted of β2-glycoprotein I (β2-GPI), a protein which was previously shown to be essential in the binding of aCL antibodies to anionic phospholipids. Prolongation of the dRVVT by aCL-type A antibodies was abolished using β2-GPI deficient plasma, but could be restored upon addition of β2-GPI. In contrast, LA IgG caused prolongation of the dRVVT irrespective of the presence or absence of β2-GPI.Since β2-GPI binds to negatively-charged phospholipids and impedes the conversion of prothrombin by the factor Xa/Va enzyme complex (Nimpf et al., Biochim Biophys Acta 1986; 884: 142–9), comparison was made of the effect of aCL-type A and aCL-type B antibodies on the rate of thrombin formation in the presence and absence of β2-GPI. This was measured in a system containing highly purified coagulation factors Xa, Va and prothrombin and lipid vesicles composed of 20 mole% phosphatidylserine and 80 mole% phosphatidylcholine. No inhibition on the rate of thrombin formation was observed with both types of aCL antibodies when either β2-GPI or the lipid vesicles were omitted. Addition of β2-GPI to the prothrombinase assay in the presence of lipid vesicles causes a time-dependent inhibition which was not affected by the presence of aCL-type B or non-specific IgG. In contrast, the presence of aCL-type A antibodies dramatically increased the anticoagulant effect of β2-GPI. These data indicate that the anticoagulant activity of aCL-type A antibodies in plasma is mediated by β2-GPI.

Feeding behaviour and bioerosion: the ecological role of the rock-boring urchin, Echinometra mathaei (de Blainville, 1825), in Okinawa reef flat

2013 ◽  
Vol 1 (1) ◽  
pp. 10
Author(s):  
Noar Muda Satyawan ◽  
Shelly Tutupoho ◽  
Yusli Wardiatno ◽  
Makoto Tsuchiya
Keyword(s):  
Feeding Behaviour ◽  
Reef Flat ◽  
Type A ◽  
Gut Contents ◽  
Biological Processes ◽  
Type B ◽  
Night Time ◽  
Echinometra Mathaei ◽  
Benthic Ecosystems

Erosion rate on corals due to activities of other biota is called bioerosion. The rock-boring urchin, Echinometra mathaei, when it is abundant, plays a significant role in benthic ecosystems, including biological processes like coral erosion. During feeding, E. mathaei erodes calcium carbonate besides grazing on algae living on coral, so it plays an important role in both organic and inorganic carbons in coral reefs. The urchin E. mathaei actively feeds during the night time (nocturnal grazer). Although in Okinawa four types (A-D) of the urchin exist, the research only focused on the types A and B. Type A of E. mathaei produced 0.44951 g feces per day on average while type B produced 0.38030 g feces per day. CaCO3 analysis in feces and gut contents showed bioerosion rate of E. mathaei type A was 0.64492 g/individu/day, and 0.54436 g/individu/day in type B. There were no significant differences in bioerosion impact of E. mathaei type A and B© Laju erosi pada karang yang disebabkan oleh biota, dikenal dengan bioerosi. Bulu babi jenis Echinometra mathaei, ketika melimpah, menjadi sangat berpengaruh terhadap ekosistem bentik termasuk proses biologi seperti erosi karang. Selama aktivitas makan, E. mathaei menggerus kalsium karbonat dalam proporsi yang besar di samping alga yang tumbuh menempel pada karang sehingga memiliki peran penting dalam siklus karbon organik dan anorganik di ekosistem terumbu karang. Bulu babi E. mathaei aktif mencari makan pada malam hari (nocturnal grazer). Meskipun di Okinanawa ada 4 tipe (A-D), pada eksperimen kali ini memfokuskan pada tipe A dan B saja. Tipe A E. mathaei rata-rata memproduksi 0,44951 g feses/hari dan tipe B memproduksi 0,38030 g feses/hari. Berdasarkan analisis CaCO3 yang dilakukan pada feses dan isi lambung, laju bioerosi yang disebabkan oleh E. mathaei tipe A sebesar 0,64492 g/individu/hari sedangkan tipe B sebesar 0,54436 g/individu/hari. Tidak terdapat perbedaan dampak bioerosi yang signifikan antara E. mathaei tipe A dan B©

Design of Pipeline Composite Repairs: From Lab Scale Tests to FEA and Full Scale Testing

2014 ◽  
Author(s):  
Remy Her ◽  
Jacques Renard ◽  
Vincent Gaffard ◽  
Yves Favry ◽  
Paul Wiet
Keyword(s):  
Finite Element ◽  
Full Scale ◽  
Combined Loading ◽  
Material Strength ◽  
Repair System ◽  
Loading Conditions ◽  
Original Design ◽  
Composite Repair ◽  
Repair Systems ◽  
Composite Properties

Composite repair systems are used for many years to restore locally the pipe strength where it has been affected by damage such as wall thickness reduction due to corrosion, dent, lamination or cracks. Composite repair systems are commonly qualified, designed and installed according to ASME PCC2 code or ISO 24817 standard requirements. In both of these codes, the Maximum Allowable Working Pressure (MAWP) of the damaged section must be determined to design the composite repair. To do so, codes such as ASME B31G for example for corrosion, are used. The composite repair systems is designed to “bridge the gap” between the MAWP of the damaged pipe and the original design pressure. The main weakness of available approaches is their applicability to combined loading conditions and various types of defects. The objective of this work is to set-up a “universal” methodology to design the composite repair by finite element calculations with directly taking into consideration the loading conditions and the influence of the defect on pipe strength (whatever its geometry and type). First a program of mechanical tests is defined to allow determining all the composite properties necessary to run the finite elements calculations. It consists in compression and tensile tests in various directions to account for the composite anisotropy and of Arcan tests to determine steel to composite interface behaviors in tension and shear. In parallel, a full scale burst test is performed on a repaired pipe section where a local wall thinning is previously machined. For this test, the composite repair was designed according to ISO 24817. Then, a finite element model integrating damaged pipe and composite repair system is built. It allowed simulating the test, comparing the results with experiments and validating damage models implemented to capture the various possible types of failures. In addition, sensitivity analysis considering composite properties variations evidenced by experiments are run. The composite behavior considered in this study is not time dependent. No degradation of the composite material strength due to ageing is taking into account. The roadmap for the next steps of this work is to clearly identify the ageing mechanisms, to perform tests in relevant conditions and to introduce ageing effects in the design process (and in particular in the composite constitutive laws).

scholarly journals CTNI-03. IMAGING FEATURES OF LEPTOMENINGEAL METASTASES OF NON-SMALL CELL LUNG CANCER: A SINGLE-CENTER REAL-WORLD STUDY

2020 ◽  
Vol 22 (Supplement_2) ◽  
pp. ii41-ii41
Author(s):  
Junjie Zhen ◽  
Lei Wen ◽  
Shaoqun Li ◽  
Mingyao Lai ◽  
Changguo Shan ◽  
...  
Keyword(s):  
Spinal Cord ◽  
Type A ◽  
Brain Parenchyma ◽  
Imaging Features ◽  
Type B ◽  
Type D ◽  
Mri Examination ◽  
Mri Features ◽  
Brain And Spinal Cord ◽  
The Brain

Abstract BACKGROUND According to EANO-ESMO clinical practice guidelines, the MRI findings of LM are divided into 4 types, namely linear enhancement (type A), nodular enhancement (type B), linear combined with nodular enhancement (type C), and sign of hydrocephalus (type D). METHODS The MRI features of brain and spinal cord in patients diagnosed with NSCLC-LM in Guangdong Sanjiu Brain Hospital from 2010 until 2019 were investigated, and then were classified into 4 types. The imaging features were analyzed. RESULTS A total of 80 patients were enrolled in the study. The median age of the patients was 53.5 years old, and the median time from the initial diagnosis to the confirmed diagnosis of LM was 11.6 months. The results of enhanced MRI examination of the brain in 79 cases showed that the number of cases with enhancements of type A, B, C and D were 50 (63.3%), 0, 26 (32.9%) and 3 (3.8%), respectively, and that LM with metastases to the brain parenchyma was found in 42 cases (53.2%). The results of enhanced MRI examination of spinal cord in 59 cases showed that there were only enhancements of type A and C in 40 cases (67.8%) and 3 cases (5.0%), and no enhancement sign in the other 16 cases (27.2%). CONCLUSION MRI examination of brain and spinal cord will improve the detection rate of LM. The MRI features of NSCLC-LM in real world are mainly characterized by the linear enhancements of brain and spinal cord, followed by linear combined with nodular enhancement. The enhancements of type B and type D are rare in clinic. Almost half of the patients have LM and metastases to the brain parenchyma. Therefore, the differentiation of tumor metastases is needed to be paid attention to for the early diagnosis and the formulation of reasonable treatment plans.

scholarly journals Molecular characterization of cytidine monophospho-N-acetylneuraminic acid hydroxylase (CMAH) gene and frequency of blood types in stray cats of İzmir, Turkey

BMC Genomics ◽  
2021 ◽  
Vol 22 (1) ◽  
Author(s):  
Hüseyin Can ◽  
Sedef Erkunt Alak ◽  
Ahmet Efe Köseoğlu ◽  
Umut Şahar ◽  
Berna Bostanbaş ◽  
...  
Keyword(s):  
Type A ◽  
Type B ◽  
Exon 2 ◽  
Blood Types ◽  
Acetylneuraminic Acid ◽  
Stray Cats ◽  
High Prevalence ◽  
Heterozygous Form ◽  
Type Ab ◽  
First Time

Abstract Background Cytidine monophospho-n-acetylneuraminic acid hydroxylase (CMAH) gene associated with blood groups in cats encodes CMAH enzyme that converts Neu5Ac to Neu5Gc. Although variations in CMAH gene of pedigree cats have been revealed, the presence/lack of them in non-pedigree stray cats is unknown. Therefore, the present study aimed to investigate the variations in CMAH gene and the quantity of Neu5Ac and Neu5Gc on erythrocytes of non-pedigree stray cats (n:12) living in İzmir, Turkey. Also, the frequency of blood types was determined in 76 stray cats including 12 cats that were used for CMAH and Neu5A/Neu5Gc analysis. Results In total, 14 SNPs were detected in 5’UTR as well as in exon 2, 4, 9, 10, 11 and 12 of CMAH gene. Among these SNPs, -495 C > T in 5’UTR was detected for the first time as heterozygous in type A and AB cats, and homozygous and heterozygous in type B cats. The remaining 13 that have been detected in previous studies were also found as homozygous or heterozygous. Both Neu5Gc and Neu5Ac were detected in type A and AB cats. In type B cats, only Neu5Ac was detected. Among two type AB cats, the level of Neu5Ac was found higher in cat carrying heterozygous form (T/C) of 1392T > C. The prevalence of type B cats (67.1 %) was higher than others. Conclusions The presence of a new SNP as well as previous SNPs indicates that more variations can be found in stray cats with a more comprehensive study in the future. Also, the high prevalence of type B cats demonstrates the possible risk of neonatal isoerythrolysis among stray cats living in İzmir, Turkey.

P5599Prognostic impact of quality indicators on outcomes of acute aortic dissection in Japan

2019 ◽  
Vol 40 (Supplement_1) ◽  
Author(s):  
T Yamaguchi ◽  
M Nakai ◽  
Y Sumita ◽  
Y Miyamoto ◽  
H Matsuda ◽  
...  
Keyword(s):  
Aortic Dissection ◽  
Hospital Mortality ◽  
Quality Indicators ◽  
Acute Aortic Dissection ◽  
Vascular Diseases ◽  
Type A ◽  
Administrative Database ◽  
Type B ◽  
Practice Gaps

Abstract Background Despite recent advances in diagnosis and management, the mortality of acute aortic dissection (AAD) remains high. Purpose This study aims to develop quality indicators (QIs) for the management of AAD, and to evaluate the associations between QIs and outcomes of AAD in a Japanese nationwide administrative database. Methods A total of 18,348 patients suffered from AAD (Type A: 10,131, Type B: 8,217) in the Japanese Registry of All Cardiac and Vascular Diseases database between 2012 and 2015 were studied. A systematic review was performed to establish initial index items for QIs. Evaluation was performed through the expert consensus meeting using a Delphi method. Associations between developed QIs and the mortality were determined by multivariate mixed logistic regression analyses. Results A total of nine QIs (five structural and four processatic) were developed. Achievements of developed QIs (High: 7–9, Middle: 4–6, Low: 0–3) were significantly associated with lower in-hospital mortality even after adjustment for covariates in both type A (Middle: odds ratio [OR], 0.257; 95% confidence interval [CI], 0.211–0.312; P<0.001; High: OR, 0.064; 95% CI, 0.047–0.086; P<0.001 vs. Low) and type B (Middle: OR, 0.447; 95% CI, 0.338–0.590; P<0.001; High: OR, 0.128; 95% CI, 0.077–0.215; P<0.001 vs. Low). Additionally, achievements of structural and processatic QIs were consistently associated with reduced in-hospital mortality. QIs and in-hospital mortality Conclusions Developed QIs for AAD management were significantly associated with lower in-hospital mortality. Evaluation of each hospital's management with QIs could be helpful to equalize quality of treatment and to fill the evidence-to-practice gaps in the real-world treatment.

scholarly journals The Carboxy-Terminal Region ofFlavobacterium johnsoniaeSprB Facilitates Its Secretion by the Type IX Secretion System and Propulsion by the Gliding Motility Machinery

2019 ◽  
Vol 201 (19) ◽  
Author(s):  
Surashree S. Kulkarni ◽  
Joseph J. Johnston ◽  
Yongtao Zhu ◽  
Zachary T. Hying ◽  
Mark J. McBride
Keyword(s):  
Amino Acids ◽  
Amino Acid ◽  
Cell Surface ◽  
Type A ◽  
Secretion System ◽  
Gliding Motility ◽  
Foreign Protein ◽  
Type B ◽  
Content Type ◽  
Type Ix Secretion System

ABSTRACTFlavobacterium johnsoniaeSprB moves rapidly along the cell surface, resulting in gliding motility. SprB secretion requires the type IX secretion system (T9SS). Proteins secreted by the T9SS typically have conserved C-terminal domains (CTDs) belonging to the type A CTD or type B CTD family. Attachment of 70- to 100-amino-acid type A CTDs to a foreign protein allows its secretion. Type B CTDs are common but have received little attention. Secretion of the foreign protein superfolder green fluorescent protein (sfGFP) fused to regions spanning the SprB type B CTD (sfGFP-CTDSprB) was analyzed. CTDs of 218 amino acids or longer resulted in secretion of sfGFP, whereas a 149-amino-acid region did not. Some sfGFP was secreted in soluble form, whereas the rest was attached on the cell surface. Surface-attached sfGFP was rapidly propelled along the cell, suggesting productive interaction with the motility machinery. This did not result in rapid cell movement, which apparently requires additional regions of SprB. Secretion of sfGFP-CTDSprBrequired coexpression withsprF, which lies downstream ofsprB. SprF is similar in sequence toPorphyromonas gingivalisPorP. MostF. johnsoniaegenes encoding proteins with type B CTDs lie immediately upstream ofporP/sprF-like genes. sfGFP was fused to the type B CTD from one such protein (Fjoh_3952). This resulted in secretion of sfGFP only when it was coexpressed with its cognate PorP/SprF-like protein. These results highlight the need for extended regions of type B CTDs and for coexpression with the appropriate PorP/SprF-like protein for efficient secretion and cell surface localization of cargo proteins.IMPORTANCETheF. johnsoniaegliding motility adhesin SprB is delivered to the cell surface by the type IX secretion system (T9SS) and is rapidly propelled along the cell by the motility machinery. How this 6,497-amino-acid protein interacts with the secretion and motility machines is not known. Fusion of the C-terminal 218 amino acids of SprB to a foreign cargo protein resulted in its secretion, attachment to the cell surface, and rapid movement by the motility machinery. Efficient secretion of SprB required coexpression with the outer membrane protein SprF. Secreted proteins that have sequence similarity to SprB in their C-terminal regions are common in the phylumBacteroidetesand may have roles in adhesion, motility, and virulence.

Study on nitrified liquor recycling process operations using polyurethane foam sponge cubes as a biomass support medium

1994 ◽  
Vol 30 (6) ◽  
pp. 143-149 ◽  
Author(s):  
H. Deguchi ◽  
M. Kashiwaya
Keyword(s):  
Experimental Study ◽  
Polyurethane Foam ◽  
Type A ◽  
Denitrification Rate ◽  
Rate Coefficients ◽  
Type B ◽  
Recycling Process ◽  
Support Medium ◽  
Suspended Growth ◽  
Nitrification And Denitrification

An experimental study was carried out to find a way of using sponge cubes as a biomass support medium to reaction tanks for nitrified liquor recycling process. Type-A, in which biomass fixed cubes are contacted with both anoxic and oxic stages and Type-B, where biomass fixed cubes are contacted with either anoxic or oxic stages, were selected as experimental cases. The results showed that the amount of CO2-C generated which was related to sludge production for Type-B exceeded the amount for Type-A by between 12 to 21%. The nitrification and denitrification rate coefficients at 20°C in Type-A were 1.5 and 1.6 times respectively higher than the coefficients for suspended growth. The rate coefficients in Type-B were 1.5 and 2.0 times respectively higher than the coefficients for Type-A.

Sign in / Sign up

Export Citation Format

Share Document