Integrity Assessment of Damaged Flexible Pipe Cross-Sections

2014 ◽  
Author(s):  
Guomin Ji ◽  
Bernt J. Leira ◽  
Svein Sævik ◽  
Frank Klæbo ◽  
Gunnar Axelsson ◽  
...  
Keyword(s):  
Cross Sections ◽  
Three Dimensional ◽  
Element Model ◽  
Computer Code ◽  
Flexible Pipe ◽  
Dynamic Stresses ◽  
Integrity Assessment ◽  
Residual Capacity ◽  
Nonlinear Finite Element Model

This paper presents results from a case study performed to evaluate the residual capacity of a 6″ flexible pipe when exposed to corrosion damages in the tensile armour. A three-dimensional nonlinear finite element model was developed using the computer code MARC to evaluate the increase in mean and dynamic stresses for a given number of damaged inner tensile armor wires. The study also includes the effect of these damages with respect to the associated stresses in the pressure spiral. Furthermore, the implications of a sequence of wire failures with respect to the accumulated time until cross-section failure in a probabilistic sense are addressed.

Numerical Analysis of a Flexible Pipe With Damaged Tensile Armor Wires

2009 ◽  
Author(s):  
Jose´ Renato M. de Sousa ◽  
Aline Nacif Pinho ◽  
Gilberto Bruno Ellwanger ◽  
Edison C. P. Lima
Keyword(s):  
Mechanical Response ◽  
High Stress ◽  
Three Dimensional ◽  
Element Model ◽  
Axial Rotation ◽  
Flexible Pipe ◽  
High Stress Concentration ◽  
Flexible Pipes ◽  
Localized Defects ◽  
Nonlinear Finite Element Model

This paper focus on the structural analysis of a 2.5″ flexible pipe with one up to five broken wires in its outer tensile armor. The pipe is supposed to be under pure tension and the effect of the number of ruptured wires on its response is discussed. A three-dimensional nonlinear finite element model devoted to analyze the local mechanical response of flexible pipes is proposed and employed in all performed analyses. This model is capable of representing each wire of the tensile armors and, therefore, localized defects, including total rupture, may be adequately represented. The obtained results pointed to high stress concentration in the wires near the damaged ones as well as a significant increase in the axial rotation of the pipe. Moreover, the stresses in the inner carcass and the pressure armor are also affected by the rupture of wires in the outer tensile armor.

scholarly journals Numerical aspects for efficient welding computational mechanics

2014 ◽  
Vol 18 (suppl.1) ◽  
pp. 139-148
Author(s):  
Tarek Aburuga ◽  
Aleksandar Sedmak ◽  
Zoran Radakovic
Keyword(s):  
Residual Stresses ◽  
Three Dimensional ◽  
Shell Element ◽  
Element Model ◽  
Mechanical Analysis ◽  
Tensile Test Specimen ◽  
Integrity Assessment ◽  
Mass Scaling ◽  
Three Dimensional Models ◽  
Thermal Mechanical Analysis

The effect of the residual stresses and strains is one of the most important parameter in the structure integrity assessment. A finite element model is constructed in order to simulate the multi passes mismatched submerged arc welding SAW which used in the welded tensile test specimen. Sequentially coupled thermal mechanical analysis is done by using ABAQUS software for calculating the residual stresses and distortion due to welding. In this work, three main issues were studied in order to reduce the time consuming during welding simulation which is the major problem in the computational welding mechanics (CWM). The first issue is dimensionality of the problem. Both two- and three-dimensional models are constructed for the same analysis type, shell element for two dimension simulation shows good performance comparing with brick element. The conventional method to calculate residual stress is by using implicit scheme that because of the welding and cooling time is relatively high. In this work, the author shows that it could use the explicit scheme with the mass scaling technique, and time consuming during the analysis will be reduced very efficiently. By using this new technique, it will be possible to simulate relatively large three dimensional structures.

Investigation on Mechanical Properties of Fibreglass Reinforced Flexible Pipes Under Torsion

2018 ◽  
Author(s):  
Pan Fang ◽  
Yuxin Xu ◽  
Shuai Yuan ◽  
Yong Bai ◽  
Peng Cheng
Keyword(s):  
Mechanical Behavior ◽  
Torsion Angle ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Load Condition ◽  
Element Model ◽  
Flexible Pipe ◽  
Torsional Load ◽  
Flexible Pipes ◽  
The Impact

Fibreglass reinforced flexible pipe (FRFP) is regarded as a great alternative to many bonded flexible pipes in the field of oil or gas transportation in shallow water. This paper describes an analysis of the mechanical behavior of FRFP under torsion. The mechanical behavior of FRFP subjected to pure torsion was investigated by experimental, analytical and numerical methods. Firstly, this paper presents experimental studies of three 10-layer FRFP subjected to torsional load. Torque-torsion angle relations were recorded during this test. Then, a theoretical model based on three-dimensional (3D) anisotropic elasticity theory was proposed to study the mechanical behavior of FRFP. In addition, a finite element model (FEM) including reinforced layers and PE layers was used to simulate the torsional load condition in ABAQUS. Torque-torsion angle relations obtained from these three methods agree well with each other, which illustrates the accuracy and reliability of the analytical model and FEM. The impact of fibreglass winding angle, thickness of reinforced layers and radius-thickness ratio were also studied. Conclusions obtained from this research may be of great practicality to manufacturing engineers.

scholarly journals Comparative Analysis of Static Loading Performance of Rigid and Flexible Road Wheel based on Finite Element Method

2020 ◽  
Vol 70 (1) ◽  
pp. 41-46
Author(s):  
Yaoji Deng ◽  
Youqun Zhao ◽  
Mingmin Zhu ◽  
Zhen Xiao ◽  
Qiuwei Wang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Static Loading ◽  
Maximum Stress ◽  
Three Dimensional ◽  
Element Model ◽  
Vertical Load ◽  
New Type ◽  
Stress And Deformation ◽  
Nonlinear Finite Element Model

To overcome the shortcomings of traditional rigid road wheel, such as poor damping effect and low load-bearing efficiency, a new type of flexible road wheel, having a unique suspension-bearing mode, was introduced. The three-dimensional nonlinear finite element model of rigid and flexible road wheel, considering the triple nonlinear characteristics of geometry, material and contact, is established for numerical investigation of static loading performance. The accuracy of the finite element model of the rigid and flexible road wheel is verified by static loading experiment. The static loading performance of the rigid and flexible road wheels is numerically analyzed. The influence of vertical load on maximum stress and deformation of the rigid and flexible wheels is also studied. The results show that the contact pressure uniformity of the flexible road wheel is better than that of the rigid road wheel under the static vertical load, but the maximum stress and deformation of the flexible road wheel are greater than that of the rigid road wheel. However, this problem can be solved by increasing the number of hinge sets and optimising the joints. The research results provide theoretical basis for replacing rigid road wheel with flexible road wheel, and also provide reference for structural optimisation of flexible road wheel.

scholarly journals Membrane analogy for multi-material bars under torsion

2019 ◽  
Vol 475 (2225) ◽  
pp. 20190124 ◽  
Author(s):  
Laura Galuppi ◽  
Gianni Royer-Carfagni
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Cross Sections ◽  
Three Dimensional ◽  
Element Model ◽  
Elastic Problem ◽  
Two Dimensional ◽  
Torsion Problem ◽  
Linear Elastic ◽  
Physical Apparatus

Prandtl's membrane analogy for the torsion problem of prismatic homogeneous bars is extended to multi-material cross sections. The linear elastic problem is governed by the same equations describing the deformation of an inflated membrane, differently tensioned in regions that correspond to the domains hosting different materials in the bar cross section, in a way proportional to the inverse of the material shear modulus. Multi-connected cross sections correspond to materials with vanishing stiffness inside the holes, implying infinite tension in the corresponding portions of the membrane. To define the interface constrains that allow to apply such a state of prestress to the membrane, a physical apparatus is proposed, which can be numerically modelled with a two-dimensional mesh implementable in commercial finite-element model codes. This approach presents noteworthy advantages with respect to the three-dimensional modelling of the twisted bar.

On the Structural Response of a Flexible Pipe With Damaged Tensile Armor Wires

2011 ◽  
Author(s):  
Jose´ Renato M. de Sousa ◽  
George C. Campello ◽  
Antoˆnio Fernando B. Bueno ◽  
Eduardo Vardaro ◽  
Gilberto B. Ellwanger ◽  
...  
Keyword(s):  
Mechanical Response ◽  
High Stress ◽  
Three Dimensional ◽  
Structural Response ◽  
Experimental Tests ◽  
Element Model ◽  
Axial Stiffness ◽  
Stress Concentrations ◽  
Flexible Pipe ◽  
Flexible Pipes

This paper studies the structural response of a 6.0″ flexible pipe under pure tension considering two different situations: the pipe is intact or has five wires broken in its outer tensile armor. A three-dimensional nonlinear finite element model devoted to analyze the local mechanical response of flexible pipes is employed in this study. This model is capable of representing each wire of the tensile armors and, therefore, localized defects, including total rupture, may be adequately represented. Results from experimental tests are also presented in order to validate the theoretical estimations. The theoretical and experimental results indicate that the imposed damage reduced the axial stiffness of the pipe. High stress concentrations in the wires near the damaged ones were also observed and, furthermore, the stresses in the inner carcass and the pressure armor are affected by the imposed damage, but, on the other hand, the normal stresses in the wires of the inner tensile armor are not.

Fracture Mechanics Analysis of a PWR Under PTS Using XFEM and Input From TRACE

2019 ◽  
Author(s):  
Diego F. Mora ◽  
Roman Mukin ◽  
Oriol Costa Garrido ◽  
Markus Niffenegger
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Fracture Mechanics ◽  
Intensity Factor ◽  
Boundary Conditions ◽  
Three Dimensional ◽  
Element Model ◽  
Integrity Assessment ◽  
Mechanics Analysis ◽  
Dynamic Cooling

Abstract In this paper, an integrity assessment of a reference Reactor Pressure Vessel (RPV) under Pressurized Thermal Shock (PTS) is performed. The assessment is based on a multi-step simulation scheme, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses. The proposed strategy uses a three dimensional (3D) finite element model (FEM) of the RPV with the Abaqus code to solve the thermo-mechanical problem for the scenario of a Large-Break Loss-of-Coolant Accident (LBLOCA). In order to obtain the boundary conditions for the thermal analysis, the thermo-hydraulic results from a 3D RPV model developed in the system code TRACE are used. The fracture mechanics analysis is carried out on submodels defined on the areas of interest. Submodels containing cracks or flaws are also located in regions of the RPV where there might be a concentration of stresses during the PTS. The calculation of stress intensity factor (SIF) makes use of the eXtended FEM (XFEM) approach. The computed SIF of the postulated cracks at the inner surface of the RPV wall are compared with the ASME fracture toughness curve of the embrittled RPV material. For different transient scenarios, the boundary conditions were previously calculated with a computational fluid dynamics (CFD) model. However, cross-verification of the results has shown consistency of both CFD and TRACE models. Moreover, the use of the later is very convenient for the integrity analyses as it is clearly less computationally expensive than CFD. Therefore, it can be used to calculate different PTS scenarios including different break sizes and break locations. The main findings from fracture mechanics analyses of the RPV subjected to LBLOCA are summarized and compared. The presented results also allow us to study the influence of the dynamic cooling plume on the stress intensity factor in more detail than with the conventional one-dimensional method. However, the plumes calculated with both approaches are different. How much this difference affects the integrity assessment of the RPV is discussed in the paper.

Finite Element Analysis of Flexible Pipes Under Axial Compression: Influence of the Sample Length

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Eduardo Ribeiro Malta ◽  
Clóvis de Arruda Martins
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Inner Core ◽  
High Sensitivity ◽  
Element Model ◽  
Sample Length ◽  
Flexible Pipe ◽  
Element Analysis ◽  
Flexible Pipes

In order to study the axial compressive behavior of flexible pipes, a nonlinear tridimensional finite element model was developed. This model recreates a five layer flexible pipe with two tensile armor layers, an external polymeric sheath, an orthotropic high strength tape, and a rigid inner core. Using this model, several studies were conducted to verify the influence of key parameters on the wire instability phenomenon. The pipe sample length can be considered as one of these parameters. This paper includes a detailed description of the finite element model itself and a case study where the length of the pipe is varied. The procedure of this analysis is here described and a case study is presented which shows that the sample length itself has no practical effect on the prebuckling response of the samples and a small effect on the limit force value. The postbuckling response, however, presented high sensitivity to the changes, but its erratic behavior has made impossible to establish a pattern.

Modelling of rotors with three-dimensional solid finite elements

2001 ◽  
Vol 36 (4) ◽  
pp. 359-371 ◽  
Author(s):  
A Nandi ◽  
S Neogy
Keyword(s):  
Finite Element ◽  
Finite Elements ◽  
Cross Sections ◽  
Three Dimensional ◽  
Element Model ◽  
Finite Element Formulation ◽  
Element Formulation ◽  
Two Dimensional ◽  
Inertia Effects ◽  
Solid Finite Elements

A shaft is modelled using three-dimensional solid finite elements. The shear-deformation and rotary inertia effects are automatically included through the three-dimensional elasticity formulation. The formulation allows warping of plane cross-sections and takes care of gyroscopic effect. Unlike a beam element model, the present model allows the actual rotor geometry to be modelled. Shafts with complicated geometry can be modelled provided that the shaft cross-section has two axes of symmetry with equal or unequal second moment of areas. The acceleration of a point on the shaft is determined in inertial and rotating frames. It is found that the finite element formulation becomes much simpler in a rotating frame of reference that rotates about the centre-line of the bearings with an angular velocity equal to the shafts spin speed. The finite element formulation in the above frame is ideally suited to non-circular shafts with solid or hollow, prismatic or tapered sections and continuous or abrupt change in cross-sections. The shaft and the disc can be modelled using the same types of element and this makes it possible to take into account the flexibility of the disc. The formulation also allows edge cracks to be modelled. A two-dimensional model of shaft disc systems executing synchronous whirl on isotropic bearings is presented. The application of the two-dimensional formulation is limited but it reduces the number of degrees of freedom. The three-dimensional solid and two-dimensional plane stress finite element models are extensively validated using standard available results.

Analysis of Mechanical Response for Subgrade of Tramcar with Monolithic Track-Bed

2013 ◽  
Vol 361-363 ◽  
pp. 1765-1771
Author(s):  
Chong Wei Huang ◽  
Shuo Wang ◽  
Xian Zhi Shao ◽  
Xian Zhao Du ◽  
Er Hao Su
Keyword(s):  
Decision Making ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Element Model ◽  
Nonlinear Finite Element ◽  
Track Structure ◽  
Concept Design ◽  
Theoretical Support ◽  
Design Basis ◽  
Nonlinear Finite Element Model

Based on the differences between the subgrade of tramcar with monolithic track-bed and the existing subgrade of railway, anew three-dimensional nonlinear finite element model is established in this paper. And then,the numerical analyses are conducted by considering weight load of track structure. The characteristics of mechanical response in the subgrade of tramcar with monolithic track-bed are found by finite analysis, which offers a reference for the future engineering, in terms of the design concept, design basis and theoretical support as well as the basis for decision making.

Sign in / Sign up

Export Citation Format

Share Document