Decarbonizing Power Generation Through the Use of Hydrogen As a Gas Turbine Fuel

2019 ◽  
Author(s):  
Michael Welch
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Carbon Content ◽  
Gas Turbine ◽  
Co2 Emissions ◽  
Gas Turbines ◽  
High Hydrogen ◽  
Wide Range ◽  
Zero Carbon ◽  
The Impact

Abstract The power generation industry has a major role to play in reducing global greenhouse gas emissions, and carbon dioxide (CO2) in particular. There are two ways to reduce CO2 emissions from power generation: improved conversion efficiency of fuel into electrical energy, and switching to lower carbon content fuels. Gas turbine generator sets, whether in open cycle, combined cycle or cogeneration configuration, offer some of the highest efficiencies possible across a wide range of power outputs. With natural gas, the fossil fuel with the lowest carbon content, as the primary fuel, they produce among the lowest CO2 emissions per kWh generated. It is possible though to decarbonize power generation further by using the fuel flexibility of the gas turbine to fully or partially displace natural gas used with hydrogen. As hydrogen is a zero carbon fuel, it offers the opportunity for gas turbines to produce zero carbon electricity. As an energy carrier, hydrogen is an ideal candidate for long-term or seasonal storage of renewable energy, while the gas turbine is an enabler for a zero carbon power generation economy. Hydrogen, while the most abundant element in the Universe, does not exist in its elemental state in nature, and producing hydrogen is an energy-intensive process. This paper looks at the different methods by which hydrogen can be produced, the impact on CO2 emissions from power generation by using pure hydrogen or hydrogen/natural gas blends, and how the economics of power generation using hydrogen compare with today’s state of the art technologies and carbon capture. This paper also addresses the issues surrounding the combustion of hydrogen in gas turbines, historical experience of gas turbines operating on high hydrogen fuels, and examines future developments to optimize combustion emissions.

Predicting Flameholding for Hydrogen and Natural Gas Flames at Gas Turbine Premixer Conditions

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Elliot Sullivan-Lewis ◽  
Vincent McDonell
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Experimental Studies ◽  
Temperature Variations ◽  
Auto Ignition ◽  
Chamber Temperature ◽  
Transient Events ◽  
Significant Effort

Lean-premixed gas turbines are now common devices for low emissions stationary power generation. By creating a homogeneous mixture of fuel and air upstream of the combustion chamber, temperature variations are reduced within the combustor, which reduces emissions of nitrogen oxides. However, by premixing fuel and air, a potentially flammable mixture is established in a part of the engine not designed to contain a flame. If the flame propagates upstream from the combustor (flashback), significant engine damage can result. While significant effort has been put into developing flashback resistant combustors, these combustors are only capable of preventing flashback during steady operation of the engine. Transient events (e.g., auto-ignition within the premixer and pressure spikes during ignition) can trigger flashback that cannot be prevented with even the best combustor design. In these cases, preventing engine damage requires designing premixers that will not allow a flame to be sustained. Experimental studies were conducted to determine under what conditions premixed flames of hydrogen and natural gas can be anchored in a simulated gas turbine premixer. Tests have been conducted at pressures up to 9 atm, temperatures up to 750 K, and freestream velocities between 20 and 100 m/s. Flames were anchored in the wakes of features typical of premixer passageways, including cylinders, steps, and airfoils. The results of this study have been used to develop an engineering tool that predicts under what conditions a flame will anchor, and can be used for development of flame anchoring resistant gas turbine premixers.

Impact of Ethane, Propane, and Diluent Content in Natural Gas on the Performance of a Commercial Microturbine Generator

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Richard L. Hack ◽  
Vincent G. McDonell
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Fuel Composition ◽  
Nox Emissions ◽  
Heating Value ◽  
Designed Experiment ◽  
Methane Number ◽  
The Impact ◽  
Lean Conditions

The impact of fuel composition on the performance of power generation devices is gaining interest as the desire to diversify fuel supplies increases. In the present study, measurements of combustion performance were conducted on a commercial natural gas-fired 60kW gas turbine as a function of fuel composition. A statistically designed experiment was carried out and exhaust emissions were obtained for significant amounts of ethane and propane. In addition, a limited study of the effect of inerts was conducted. The results show that emissions of NOx, CO, and NOx∕NO are not well correlated with common descriptions of the fuel, such as higher heating value or methane number. The results and trends indicate that the presence of higher hydrocarbons in the fuel leads to appreciably higher NOx emissions for both test devices operating under similar lean conditions, while having less impact on CO emissions.

Uncertainty Analysis of Inflow Conditions on an HPT Gas Turbine Nozzle: Effect on Particle Deposition

2020 ◽  
Author(s):  
R. Friso ◽  
N. Casari ◽  
M. Pinelli ◽  
A. Suman ◽  
F. Montomoli
Keyword(s):  
Gas Turbine ◽  
Energy Efficient ◽  
Gas Turbines ◽  
Particle Deposition ◽  
Operating Conditions ◽  
Wide Range ◽  
And Performance ◽  
Gas Turbine Nozzle ◽  
The Impact ◽  
Inflow Conditions

Abstract Gas turbines (GT) are often forced to operate in harsh environmental conditions. Therefore, the presence of particles in their flow-path is expected. With this regard, deposition is a problem that severely affects gas turbine operation. Components’ lifetime and performance can dramatically vary as a consequence of this phenomenon. Unfortunately, the operating conditions of the machine can vary in a wide range, and they cannot be treated as deterministic. Their stochastic variations greatly affect the forecasting of life and performance of the components. In this work, the main parameters considered affected by the uncertainty are the circumferential hot core location and the turbulence level at the inlet of the domain. A stochastic analysis is used to predict the degradation of a high-pressure-turbine (HPT) nozzle due to particulate ingestion. The GT’s component analyzed as a reference is the HPT nozzle of the Energy-Efficient Engine (E3). The uncertainty quantification technique used is the probabilistic collocation method (PCM). This work shows the impact of the operating conditions uncertainties on the performance and lifetime reduction due to deposition. Sobol indices are used to identify the most important parameter and its contribution to life. The present analysis enables to build confidence intervals on the deposit profile and on the residual creep-life of the vane.

Operation Experiences of Siemens IGCC Gas Turbines Using Gasification Products From Coal and Refinery Residues

2000 ◽  
Author(s):  
M. Huth ◽  
A. Heilos ◽  
G. Gaio ◽  
J. Karg
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Strong Impact ◽  
Coal Gas ◽  
Operation Conditions ◽  
Wide Range ◽  
Commercial Operation ◽  
Burner Design

The Integrated Gasification Combined Cycle concept is an emerging technology that enables an efficient and clean use of coal as well as residuals in power generation. After several years of development and demonstration operation, now the technology has reached the status for commercial operation. SIEMENS is engaged in 3 IGCC plants in Europe which are currently in operation. Each of these plants has specific characteristics leading to a wide range of experiences in development and operation of IGCC gas turbines fired with low to medium LHV syngases. The worlds first IGCC plant of commercial size at Buggenum/Netherlands (Demkolec) has already demonstrated that IGCC is a very efficient power generation technology for a great variety of coals and with a great potential for future commercial market penetration. The end of the demonstration period of the Buggenum IGCC plant and the start of its commercial operation has been dated on January 1, 1998. After optimisations during the demonstration period the gas turbine is running with good performance and high availability and has exceeded 18000 hours of operation on coal gas. The air-side fully integrated Buggenum plant, equipped with a Siemens V94.2 gas turbine, has been the first field test for the Siemens syngas combustion concept, which enables operation with very low NOx emission levels between 120–600 g/MWh NOx corresponding to 6–30 ppm(v) (15%O2) and less than 5 ppm(v) CO at baseload. During early commissioning the syngas nozzle has been recognised as the most important part with strong impact on combustion behaviour. Consequently the burner design has been adjusted to enable quick and easy changes of the important syngas nozzle. This design feature enables fast and efficient optimisations of the combustion performance and the possibility for easy adjustments to different syngases with a large variation in composition and LHV. During several test runs the gas turbine proved the required degree of flexibility and the capability to handle transient operation conditions during emergency cases. The fully air-side integrated IGCC plant at Puertollano/Spain (Elcogas), using the advanced Siemens V94.3 gas turbine (enhanced efficiency), is now running successfully on coal gas. The coal gas composition at this plant is similar to the Buggenum example. The emission performance is comparable to Buggenum with its very low emission levels. Currently the gas turbine is running for the requirements of final optimization runs of the gasifier unit. The third IGCC plant (ISAB) equipped with Siemens gas turbine technology is located at Priolo near Siracusa at Sicilly/Italy. Two Siemens V94.2K (modified compressor) gas turbines are part of this “air side non-integrated” IGCC plant. The feedstock of the gasification process is a refinery residue (asphalt). The LHV is almost twice compared to the Buggenum or Puertollano case. For operation with this gas, the coal gas burner design was adjusted and extensively tested. IGCC operation without air extraction has been made possible by modifying the compressor, giving enhanced surge margins. Commissioning on syngas for the first of the two gas turbines started in mid of August 1999 and was almost finished at the end of August 1999. The second machine followed at the end of October 1999. Since this both machines are released for operation on syngas up to baseload.

Performance Analysis of a Solar–Biogas Hybrid Micro Gas Turbine for Power Generation

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Saad Alshahrani ◽  
Abraham Engeda
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Co2 Emissions ◽  
Gas Turbines ◽  
Meteorological Condition ◽  
Fuel Gas ◽  
Micro Gas Turbine ◽  
Fuel Savings ◽  
Solar Power Tower ◽  
To Receive

Abstract A performance assessment was conducted for a solar–biogas hybrid micro gas turbine integrated with a solar power tower technology. The considered system is a solar central receiver integrated with a micro gas turbine hybrid with biogas fuel as a backup. The Brayton cycle is designed to receive a dual integrated heat source input that works alternatively to keep the heat input to the system continuous. The study considered several key performance parameters including meteorological condition effects, recuperator existence and effectiveness, solar share, and gas turbine components performance. This study shows a significant reduction in CO2 emissions due to the utilization and hybridization of the renewable energies, solar, and biogas. The study reveals that the solar–biogas hybrid micro gas turbine for 100-kW power production has a CO2 emission less than a conventional fossil fuel gas turbine. Finally, the study shows that the method of power generation hybridization for solar and biogas gas turbines is a promising technique that leads to fuel-savings and lower CO2 emissions.

Analysis of Indirectly Fired Gas Turbine Power Systems

2007 ◽  
Author(s):  
J. E. Donald Gauthier
Keyword(s):  
Power Generation ◽  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Turbine Engine ◽  
Engine Design ◽  
Wide Range ◽  
System Configurations

This paper describes the results of modelling the performance of several indirectly fired gas turbine (IFGT) power generation system configurations based on four gas turbine class sizes, namely 5 kW, 50 kW, 5 MW and 100 MW. These class sizes were selected to cover a wide range of installations in residential, commercial, industrial and large utility power generation installations. Because the IFGT configurations modelled consist of a gas turbine engine, one or two recuperators and a furnace; for comparison purpose this study also included simulations of simple cycle and recuperated gas turbine engines. Part-load, synchronous-speed simulations were carried out with generic compressor and turbine maps scaled for each engine design point conditions. The turbine inlet temperature (TIT) was varied from the design specification to a practical value for a metallic high-temperature heat exchanger in an IFGT system. As expected, the results showed that the reduced TIT can have dramatic impact on the power output and thermal efficiency when compared to that in conventional gas turbines. However, the simulations also indicated that several configurations can lead to higher performance, even with the reduced TIT. Although the focus of the study is on evaluation of thermodynamic performance, the implications of varying configurations on cost and durability are also discussed.

Sequential Combustion in Gas Turbines: The Key Technology for Burning High Hydrogen Contents With Low Emissions

2019 ◽  
Author(s):  
Mirko R. Bothien ◽  
Andrea Ciani ◽  
John P. Wood ◽  
Gerhard Fruechtel
Keyword(s):  
High Pressure ◽  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Tuning Parameter ◽  
High Hydrogen ◽  
Stable Combustion ◽  
Second Stage ◽  
In Series ◽  
Exit Temperature

Abstract Excess energy generation from renewables can be conveniently stored as hydrogen for later use as a gas turbine fuel. Also, the strategy to sequestrate CO2 from natural gas will require gas turbines to run with hydrogen-based fuels. In such scenarios, high temperature low emission combustion of hydrogen is a key requirement for the future gas turbine market. Ansaldo Energia’s gas turbines featuring sequential combustion have an intrinsic advantage when it comes to fuel flexibility and in particular hydrogen-based fuels. The sequential combustion system is composed of two complementary combustion stages in series: one premix stage followed by an auto-ignited second stage overcoming the limits of traditional premix combustion systems through a highly effective extra tuning parameter, i.e. the temperature between the first and the second stage. The standard Constant Pressure Sequential Combustion (CPSC) system as applied in the GT36 engine is tested, at high pressure, demonstrating that a modified operation concept allows stable combustion with no changes in combustor hardware for the whole range of natural gas and hydrogen blends. It is shown that in the range from 0% to 70% (vol.) hydrogen, stable combustion is achieved at full nominal exit temperature, i.e. without any derating and thus clearly outperforming other available conventional premixed combustors. Operation between 70% and 100% is possible as well and only requires a mild reduction of the combustor exit temperature. By proving the transferability of the single-can high pressure results to the engine, this paper demonstrates the practicality of operating the Ansaldo Energia GT36 H-Class gas turbine on fuels containing unprecedented concentrations of hydrogen while maintaining excellent performance and low emissions both in terms of NOx and CO2.

Risk-Based Assessment of Unplanned Outage Events and Costs for Combined-Cycle-Plants

2012 ◽  
Author(s):  
Dale Grace ◽  
Thomas Christiansen
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Cash Flow ◽  
Gas Turbines ◽  
Operational Reliability ◽  
Combined Cycle ◽  
Maintenance Costs ◽  
Wide Range ◽  
Turbine Equipment ◽  
The Impact

Unexpected outages and maintenance costs reduce plant availability and can consume significant resources to restore the unit to service. Although companies may have the means to estimate cash flow requirements for scheduled maintenance and on-going operations, estimates for unplanned maintenance and its impact on revenue are more difficult to quantify, and a large fleet is needed for accurate assessment of its variability. This paper describes a study that surveyed 388 combined-cycle plants based on 164 D/E-class and 224 F-class gas turbines, for the time period of 1995 to 2009. Strategic Power Systems, Inc. (SPS®), manager of the Operational Reliability Analysis Program (ORAP®), identified the causes and durations of forced outages and unscheduled maintenance and established overall reliability and availability profiles for each class of plant in 3 five-year time periods. This study of over 3,000 unit-years of data from 50 Hz and 60 Hz combined-cycle plants provides insight into the types of events having the largest impact on unplanned outage time and cost, as well as the risks of lost revenue and unplanned maintenance costs which affect plant profitability. Outage events were assigned to one of three subsystems: the gas turbine equipment, heat recovery steam generator (HRSG) equipment, or steam turbine equipment, according to the Electric Power Research Institute’s Equipment Breakdown Structure (EBS). Costs to restore the unit to service for each main outage cause were estimated, as were net revenues lost due to unplanned outages. A statistical approach to estimated costs and lost revenues provides a risk-based means to quantify the impact of unplanned events on plant cash flow as a function of class of gas turbine, plant subsystem, and historical timeframe. This statistical estimate of the costs of unplanned outage events provides the risk-based assessment needed to define the range of probable costs of unplanned events. Results presented in this paper demonstrate that non-fuel operation and maintenance costs are increased by roughly 8% in a typical combined-cycle power plant due to unplanned maintenance events, but that a wide range of costs can occur in any single year.

Experimental Investigation of the Performance of a Micro Gas Turbine Fueled With Mixtures of Natural Gas and Biogas

2013 ◽  
Author(s):  
Homam Nikpey ◽  
Mohsen Assadi ◽  
Peter Breuhaus
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Co2 Emissions ◽  
Fuel Mixture ◽  
Combined Heat And Power ◽  
Test Rig ◽  
Heating Value ◽  
Micro Gas Turbine ◽  
Fuel Mixtures ◽  
The Impact

Previously published studies have addressed modifications to the engines when operating with biogas, i.e. a low heating value (LHV) fuel. This study focuses on mapping out the possible biogas share in a fuel mixture of biogas and natural gas in micro combined heat and power (CHP) installations without any engine modifications. This contributes to a reduction in CO2 emissions from existing CHP installations and makes it possible to avoid a costly upgrade of biogas to the natural gas quality as well as engine modifications. Moreover, this approach allows the use of natural gas as a “fallback” solution in the case of eventual variations of the biogas composition and or shortage of biogas, providing improved availability. In this study, the performance of a commercial 100kW micro gas turbine (MGT) is experimentally evaluated when fed by varying mixtures of natural gas and biogas. The MGT is equipped with additional instrumentation, and a gas mixing station is used to supply the demanded fuel mixtures from zero biogas to maximum possible level by diluting natural gas with CO2. A typical biogas composition with 0.6 CH4 and 0.4 CO2 (in mole fraction) was used as reference, and corresponding biogas content in the supplied mixtures was computed. The performance changes due to increased biogas share were studied and compared with the purely natural gas fired engine. This paper presents the test rig setup used for the experimental activities and reports results, demonstrating the impact of burning a mixture of biogas and natural gas on the performance of the MGT. Comparing with when only natural gas was fired in the engine, the electrical efficiency was almost unchanged and no significant changes in operating parameters were observed. It was also shown that burning a mixture of natural gas and biogas contributes to a significant reduction in CO2 emissions from the plant.

scholarly journals Prediction of Auto-Ignition Temperatures and Delays for Gas Turbine Applications

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Roda Bounaceur ◽  
Pierre-Alexandre Glaude ◽  
Baptiste Sirjean ◽  
René Fournet ◽  
Pierre Montagne ◽  
...  
Keyword(s):  
High Temperature ◽  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Equivalence Ratio ◽  
Process Conditions ◽  
Piping System ◽  
Gaseous Fuels ◽  
Auto Ignition ◽  
Wide Range

Gas turbines burn a large variety of gaseous fuels under elevated pressure and temperature conditions. During transient operations, variable gas/air mixtures are involved in the gas piping system. In order to predict the risk of auto-ignition events and ensure a safe operation of gas turbines, it is of the essence to know the lowest temperature at which spontaneous ignition of fuels may happen. Experimental auto-ignition data of hydrocarbon–air mixtures at elevated pressures are scarce and often not applicable in specific industrial conditions. Auto-ignition temperature (AIT) data correspond to temperature ranges in which fuels display an incipient reactivity, with timescales amounting in seconds or even in minutes instead of milliseconds in flames. In these conditions, the critical reactions are most often different from the ones governing the reactivity in a flame or in high temperature ignition. Some of the critical paths for AIT are similar to those encountered in slow oxidation. Therefore, the main available kinetic models that have been developed for fast combustion are unfortunately unable to represent properly these low temperature processes. A numerical approach addressing the influence of process conditions on the minimum AIT of different fuel/air mixtures has been developed. Several chemical models available in the literature have been tested, in order to identify the most robust ones. Based on previous works of our group, a model has been developed, which offers a fair reconciliation between experimental and calculated AIT data through a wide range of fuel compositions. This model has been validated against experimental auto-ignition delay times corresponding to high temperature in order to ensure its relevance not only for AIT aspects but also for the reactivity of gaseous fuels over the wide range of gas turbine operation conditions. In addition, the AITs of methane, of pure light alkanes, and of various blends representative of several natural gas and process-derived fuels were extensively covered. In particular, among alternative gas turbine fuels, hydrogen-rich gases are called to play an increasing part in the future so that their ignition characteristics have been addressed with particular care. Natural gas enriched with hydrogen, and different syngas fuels have been studied. AIT values have been evaluated in function of the equivalence ratio and pressure. All the results obtained have been fitted by means of a practical mathematical expression. The overall study leads to a simple correlation of AIT versus equivalence ratio/pressure.

Sign in / Sign up

Export Citation Format

Share Document