Geometry and Speed Effects on the Performance of the Herringbone Grooved Gas Lubricated Journal Bearing

2005 ◽  
Author(s):  
D. J. Foster
Keyword(s):  
Reynolds Equation ◽  
Journal Bearing ◽  
Groove Depth ◽  
Bearing Surface ◽  
Static Stiffness ◽  
Groove Pattern ◽  
Land Width

The plain gas lubricated journal bearing is dynamically unstable. The addition of grooving on the bearing surface has been found to overcome this instability. In particular, the herringbone groove pattern has been found to provide damping with increase of static stiffness. The effect of the available geometry characteristics on performance is computed from solution of the compressible Reynolds equation. The geometry features examined are groove angle, and the ratios:- groove depth to clearance, groove-to-land width, axial groove length to bearing length and bearing eccentricity. The performance is determined over a range of compressibility numbers.

Performance Analysis of Grooved Hydrodynamic Journal Bearing with Multi-Depth Textured Surface

2018 ◽  
Vol 10 (2) ◽  
Author(s):  
K.M Faez ◽  
S Hamdavi ◽  
T.V.V.L.N. Rao ◽  
H.H Ya ◽  
Norani M. Mohamed
Keyword(s):  
Reynolds Equation ◽  
Journal Bearing ◽  
Load Capacity ◽  
Textured Surface ◽  
Plain Bearing ◽  
Bearing Surface ◽  
Grooved Surface ◽  
Hydrodynamic Journal Bearing ◽  
Efficiency And Reliability ◽  
Capacity Performance

In recent research, theoretical studies and investigations for the textured surface of a hydrodynamic journal bearing has been widely used. This is due to the journal bearing’s performance in terms of load capacity which affects the system performance, efficiency and reliability. It has been proven that a textured surface and grooved surface have managed to improve the performance of journal bearings to some extent. In this work, the performance of a grooved hydrodynamic journal bearing has been analysed with a multi-depth textured surface. The study has been conducted using the modified Reynolds equation to numerically solve the load capacity and pressure distribution, respectively. From the results obtained, it was found that the surface complexity features on the journal bearing lowered the load capacity performance when compared to the plain bearing. The pressure, meanwhile, was distributed throughout the textured sections on the bearing surface, even though it was lower as compared to the plain bearing.

Micro Thermal Elastohydrodynamic Lubrication Analysis of Power Law Water-Based Ferrofluid Journal Bearing

2013 ◽  
Vol 694-697 ◽  
pp. 543-546 ◽  
Author(s):  
Xiu Jiang Shi ◽  
You Qiang Wang
Keyword(s):  
Film Thickness ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Elastohydrodynamic Lubrication ◽  
Peak Height ◽  
Bearing Surface ◽  
Roughness Model ◽  
Water Based ◽  
Fluctuation Range ◽  
The Magnetic Field

Based on the Reynolds equation considering the temperature, the effection of non-newtonian and the magnetic field, the elastohydrodynamic lubrication(EHL) analysis of water-based ferrofluid journal bearing were carried out. The influence of roughness peak height and wavelength on the journal bearing surface with cosine roughness model were analysed. The results reveal that the pressure and film thickness of water-based ferrofluid wave apparently with roughness fluctuation; The fluctuation range of pressure and film thickness increase with the increase of roughness peak height, the minimal film thickness decreases; The pressure and film thickness fluctuation range become more and more sparse with the increase of roughness wavelength, the minimal film thickness increases.

scholarly journals Theoretical investigation of porous hydrostatic journal bearing under micropolar fluid lubrication

2020 ◽  
Vol 234 (1-2) ◽  
pp. 11-18
Author(s):  
Biplab Bhattacharjee ◽  
Prasun Chakraborti ◽  
Kishan Choudhuri
Keyword(s):  
Carrying Capacity ◽  
Micropolar Fluid ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Low Flow ◽  
Load Carrying Capacity ◽  
Static Stiffness ◽  
Design Charts ◽  
Hydrostatic Bearings ◽  
Load Carrying

The features of micropolar fluid (a non-Newtonian fluid)–lubricated short single-layered porous hydrostatic journal bearing are analyzed theoretically by an iterative method. To investigate hydrostatic journal bearing characteristics, a modified Reynolds equation in the case of micropolar fluid is derived and solved numerically. The obtained results in this work are validated by comparing the same with previously published results with Newtonian and non-Newtonian lubricants in the form of design charts. The static stiffness and load-carrying capacity of the investigated bearing are 80% and 75% higher than conventional hydrostatic bearings. The porous hydrostatic journal bearing exhibits more economical performance as it requires 40% low flow rate and low pump power, and it generates 50% less heat in contrast with other hydrostatic bearings.

Influence of dimple location and depth on the performance characteristics of the hydrodynamic journal bearing system

2020 ◽  
Vol 234 (9) ◽  
pp. 1500-1513
Author(s):  
Niranjan Singh ◽  
RK Awasthi
Keyword(s):  
Reynolds Equation ◽  
Journal Bearing ◽  
Dynamic Performance ◽  
Performance Characteristics ◽  
Eccentricity Ratio ◽  
Bearing Surface ◽  
Surface Textures ◽  
Hydrodynamic Journal Bearing ◽  
Theoretical Results ◽  
Bearing System

This paper concerns with theoretical investigation to predict the influence of cylindrical textures on the static and dynamic performance characteristics of hydrodynamic journal bearing system and the performance is compared with smooth surface bearing. The Reynolds equation governing the fluid–film between the journal and the bearing surface is solved numerically with the assistance of finite element method and the performance characteristics are evaluated as a function of eccentricity ratio, dimple depth and its location. In this study, four journal bearing configurations viz: smooth (non-textured), full-textured, partially textured-I, and partially textured-II are considered for the evaluation of theoretical results. The simulated results indicate that the influence of surface textures is more significant when the textures were created in upstream zone of 126°–286° and dimple aspect ratio nearly 1.0.

LOAD CAPACITY COEFFICIENT EVALUATION OF THREE-LAYERED JOURNAL BEARING WITH SLIP

2016 ◽  
Vol 78 (6-10) ◽  
Author(s):  
T. V. V. L. N. Rao ◽  
A. M. A. Rani ◽  
M. Awang ◽  
F. M. Hashim
Keyword(s):  
Reynolds Equation ◽  
Journal Bearing ◽  
Load Capacity ◽  
High Viscosity ◽  
Bearing Surface ◽  
Surface Layers ◽  
Navier Slip ◽  
Slip Boundary ◽  
Capacity Coefficient ◽  
Navier Slip Boundary Conditions

Analysis of three-layered journal bearing with slip on bearing surface is presented. A modified classical Reynolds equation is derived for slip on bearing surface taking into consideration of bearing surface, core and journal surface layers. The modified Reynolds equation is derived taking into consideration of lubricant layer’s film thickness, viscosities and slip on the bearing surface. Navier slip boundary conditions are used to analyze slip. Results of load capacity coefficient are presented for three-layered and two-layered journal bearing with slip. The load capacity coefficient decreases with bearing surface with slip. For a three-layered journal bearing with slip, high viscosity bearing surface layer results in higher load capacity coefficient.

A General Solution of Reynolds’ Equation for a Full Finite Journal Bearing

1967 ◽  
Vol 89 (2) ◽  
pp. 203-210 ◽  
Author(s):  
R. R. Donaldson
Keyword(s):  
Fourier Series ◽  
Series Solution ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Load Capacity ◽  
Separation Of Variables ◽  
Hill Equation ◽  
Eigenvalues And Eigenvectors ◽  
General Series ◽  
Bearing Load

Reynolds’ equation for a full finite journal bearing lubricated by an incompressible fluid is solved by separation of variables to yield a general series solution. A resulting Hill equation is solved by Fourier series methods, and accurate eigenvalues and eigenvectors are calculated with a digital computer. The finite Sommerfeld problem is solved as an example, and precise values for the bearing load capacity are presented. Comparisons are made with the methods and numerical results of other authors.

Characteristics of Herringbone-Grooved, Gas-Lubricated Journal Bearings

1965 ◽  
Vol 87 (3) ◽  
pp. 568-576 ◽  
Author(s):  
J. H. Vohr ◽  
C. Y. Chow
Keyword(s):  
Differential Equation ◽  
Journal Bearing ◽  
Groove Depth ◽  
Radial Force ◽  
Journal Bearings ◽  
Speed Ratio ◽  
Plain Bearing ◽  
Relative Speed ◽  
Whirl Speed ◽  
Limiting Case

A differential equation is obtained for the smoothed “overall” pressure distribution around a herringbone-grooved, gas-lubricated journal bearing operating with a variable film thickness. The equation is based on the limiting case of an idealized bearing for which the number of grooves approaches an infinite number. A numerical solution to the differential equation is obtained valid for small eccentricities. This solution includes the case where the journal is undergoing steady circular whirl. In addition to the usual plain bearing parameters L/D, Λ, and whirl speed ratio ω3/(ω1 + ω2), the behavior of a grooved bearing also depends on four additional parameters: The groove angle β, the relative groove width α, the relative groove depth H0, and a compressibility number, Λs, which is based on the relative speed between the grooved and smooth members of the bearing. Results are presented showing bearing radial force and attitude angle as functions of β, α, H0, Λs, Λ, and whirl speed ratio.

Theoretical Condition for the Cxy=Cyx Relation in Fluid Film Journal Bearings

1989 ◽  
Vol 111 (3) ◽  
pp. 426-429 ◽  
Author(s):  
T. Kato ◽  
Y. Hori
Keyword(s):  
Reynolds Equation ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Fluid Film ◽  
Finite Width ◽  
Damping Coefficients ◽  
Dynamic Coefficients ◽  
Cross Terms ◽  
Linear Damping ◽  
Theoretical Condition

A computer program for calculating dynamic coefficients of journal bearings is necessary in designing fluid film journal bearings and an accuracy of the program is sometimes checked by the relation that the cross terms of linear damping coefficients of journal bearings are equal to each other, namely “Cxy = Cyx”. However, the condition for this relation has not been clear. This paper shows that the relation “Cxy = Cyx” holds in any type of finite width journal bearing when these are calculated under the following condition: (I) The governing Reynolds equation is linear in pressure or regarded as linear in numerical calculations; (II) Film thickness is given by h = c (1 + κcosθ); and (III) Boundary condition is homogeneous such as p=0 or dp/dn=0, where n denotes a normal to the boundary.

The Effect of Lubricant Inertia in Journal-Bearing Lubrication

1957 ◽  
Vol 24 (4) ◽  
pp. 494-496
Author(s):  
J. F. Osterle ◽  
Y. T. Chou ◽  
E. A. Saibel
Keyword(s):  
Reynolds Number ◽  
Steady State ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Hydrodynamic Theory ◽  
Simple Relationship ◽  
Inertia Effect ◽  
Laminar Regime ◽  
Steady State Operation

Abstract The Reynolds equation of hydrodynamic theory, modified to take lubricant inertia into approximate account, is applied to the steady-state operation of journal bearings to determine the effect of lubricant inertia on the pressure developed in the lubricant. A simple relationship results, relating this “inertial” pressure to the Reynolds number of the flow. It is found that the inertia effect can be significant in the laminar regime.

Numerical and Experimental Investigations on Preload Effects in Air Foil Journal Bearings

2017 ◽  
Author(s):  
Marcel Mahner ◽  
Pu Li ◽  
Andreas Lehn ◽  
Bernhard Schweizer
Keyword(s):  
Reynolds Equation ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Compressible Fluids ◽  
Experimental Investigations ◽  
Hysteresis Curves ◽  
Numerical Predictions ◽  
Bearing Stiffness ◽  
Gasdynamic Model ◽  
Good Agreement

A detailed elasto-gasdynamic model of a preloaded three-pad air foil journal bearing is presented. Bump and top foil deflections are herein calculated with a nonlinear beamshell theory according to Reissner. The 2D pressure distribution in each bearing pad is described by the Reynolds equation for compressible fluids. With this model, the influence of the assembly preload on the static bearing hysteresis as well as on the aerodynamic bearing performance is investigated. For the purpose of model validation, the predicted hysteresis curves are compared with measured curves. The numerically predicted and the measured hysteresis curves show a good agreement. The numerical predictions exhibit that the assembly preload increases the bearing stiffness (in particular for moderate shaft displacements) and the bearing damping.

Sign in / Sign up

Export Citation Format

Share Document