The output vector formation in the system of multi-alternative automatic control of optical diffraction spectral devices

2020 ◽  
Author(s):  
Vasily I. Kazakov ◽  
Oleg D. Moskaletz ◽  
Arthur S. Paraskun ◽  
Kseniia Serdiuk
Keyword(s):  
Automatic Control ◽  
Optical Diffraction ◽  
Output Vector

scholarly journals SYNTHESIS OF THE OPTIMAL OBSERVER IN THE ABSENCE OF APRIORI INFORMATION ABOUT THE NOISE CHARACTERISTICS OF THE AUTOMATIC CONTROL AND MONITORING SYSTEM OF A TURBOFAN ENGINES

2020 ◽  
pp. 71-80
Author(s):  
Aleksandr Inozemtsev ◽  
◽  
Nadezhda Lamanova ◽  
Alexey Sazhenkov ◽  
Igor Gribkov ◽  
...  
Keyword(s):  
Kalman Filter ◽  
Comparative Analysis ◽  
Automatic Control ◽  
Monitoring System ◽  
Adaptive Filter ◽  
Turbofan Engine ◽  
Output Vector ◽  
Computational Costs ◽  
System Noise ◽  
Control And Monitoring System

The possibility of obtaining measuring in-formation about the parameters of the automatic control and monitoring system of a turbofan engine during its operation in flight conditions and almost no restrictions on computational costs enable using algo-rithmic methods to improve the engine fault tolerance. In the previous article, the optimal observer, the Kalman filter, was used as a reserve meter. Its functioning essentially depends on the probabilistic characteristics of the system noise, which is known approximately and changes in a complex man-ner over time. Inaccuracies in these characteristics can lead to filter divergence and loss of its stability. To solve this problem, it is proposed to use the Yazvinsky adaptive filter, which allows calculating the covariance matrix of the disturbance noise after the arrival of new measurements from the values of the updated process of the Kaman filter. In this case computational costs increase insignificantly. The use of the Yazvsky adaptive filter eliminates the need for preliminary correlation analysis of system noise and pro-tects the Kalman filter from loss of stability. The results of modeling the Yazvinsky filter, consistent with the mathematical model of the turbofan engine, based on the flight test data of the PS-90A type engine as part of the TU-214 aircraft, both in steady-state and transient modes of engine operation, are presented. The parameters are indicated as percentage of the maximum values. A comparative analysis of the actual errors in the estimation of the output vector of the turbofan engine ACS when Kal-man and Yazvinsky filters are operating is carried out. The results of the comparative analysis are presented in the form of tables and graphs. It is shown that the proposed algorithm ensures fulfillment of the requirements for the accuracy of estimating the output vector of the automatic control and monitoring system of a gas turbine engine and can be recommended for use in the ACS of the turbofan engine.

Light Optical Diffraction Studies of Macromolecular Ultrastructure

1970 ◽  
Vol 28 ◽  
pp. 258-259
Author(s):  
Glen B. Haydon
Keyword(s):  
High Resolution ◽  
Diffraction Analysis ◽  
Diffraction Pattern ◽  
Electron Micrographs ◽  
Optical Diffraction ◽  
Electron Micrograph ◽  
Its Analysis ◽  
Resolution Electron ◽  
Diffraction Patterns

Analysis of light optical diffraction patterns produced by electron micrographs can easily lead to much nonsense. Such diffraction patterns are referred to as optical transforms and are compared with transforms produced by a variety of mathematical manipulations. In the use of light optical diffraction patterns to study periodicities in macromolecular ultrastructures, a number of potential pitfalls have been rediscovered. The limitations apply to the formation of the electron micrograph as well as its analysis.(1) The high resolution electron micrograph is itself a complex diffraction pattern resulting from the specimen, its stain, and its supporting substrate. Cowley and Moodie (Proc. Phys. Soc. B, LXX 497, 1957) demonstrated changing image patterns with changes in focus. Similar defocus images have been subjected to further light optical diffraction analysis.

Recent Applications of High Resolution Electron Microscopy to Crystalline Arrays of Virus Particles

1978 ◽  
Vol 36 (3) ◽  
pp. 470-482 ◽  
Author(s):  
R.W. Horne
Keyword(s):  
Electron Microscopy ◽  
Image Processing ◽  
Analytical Techniques ◽  
Staining Technique ◽  
High Resolution Electron Microscopy ◽  
Optical Diffraction ◽  
Full Potential ◽  
Virus Particles ◽  
Resolution Electron ◽  
Wide Range

The technique of surrounding virus particles with a neutralised electron dense stain was described at the Fourth International Congress on Electron Microscopy, Berlin 1958 (see Home & Brenner, 1960, p. 625). For many years the negative staining technique in one form or another, has been applied to a wide range of biological materials. However, the full potential of the method has only recently been explored following the development and applications of optical diffraction and computer image analytical techniques to electron micrographs (cf. De Hosier & Klug, 1968; Markham 1968; Crowther et al., 1970; Home & Markham, 1973; Klug & Berger, 1974; Crowther & Klug, 1975). These image processing procedures have allowed a more precise and quantitative approach to be made concerning the interpretation, measurement and reconstruction of repeating features in certain biological systems.

Microdensitometer—computer correlation analysis of ultrastructural periodicity

1978 ◽  
Vol 36 (2) ◽  
pp. 32-33
Author(s):  
D.R. Ensor ◽  
C.G. Jensen ◽  
J.A. Fillery ◽  
R.J.K. Baker
Keyword(s):  
Correlation Analysis ◽  
Background Noise ◽  
Computer Control ◽  
Optical Diffraction ◽  
Screw Thread ◽  
Straight Line ◽  
Computer Storage ◽  
Correlation Process ◽  
Electron Microscope Image ◽  
Fixed Beam

Because periodicity is a major indicator of structural organisation numerous methods have been devised to demonstrate periodicity masked by background “noise” in the electron microscope image (e.g. photographic image reinforcement, Markham et al, 1964; optical diffraction techniques, Horne, 1977; McIntosh,1974). Computer correlation analysis of a densitometer tracing provides another means of minimising "noise". The correlation process uncovers periodic information by cancelling random elements. The technique is easily executed, the results are readily interpreted and the computer removes tedium, lends accuracy and assists in impartiality.A scanning densitometer was adapted to allow computer control of the scan and to give direct computer storage of the data. A photographic transparency of the image to be scanned is mounted on a stage coupled directly to an accurate screw thread driven by a stepping motor. The stage is moved so that the fixed beam of the densitometer (which is directed normal to the transparency) traces a straight line along the structure of interest in the image.

Structural analysis of the surface-layer protein of spirillum serpens by high-resolution electron microscopy

1983 ◽  
Vol 41 ◽  
pp. 738-739
Author(s):  
W. H. Wu ◽  
R. M. Glaeser
Keyword(s):  
Electron Microscopy ◽  
Surface Layer ◽  
Structural Analysis ◽  
High Resolution ◽  
Low Dose ◽  
High Resolution Electron Microscopy ◽  
Optical Diffraction ◽  
Surface Layer Protein ◽  
Morphological Unit ◽  
Resolution Electron

Spirillum serpens possesses a surface layer protein which exhibits a regular hexagonal packing of the morphological subunits. A morphological model of the structure of the protein has been proposed at a resolution of about 25 Å, in which the morphological unit might be described as having the appearance of a flared-out, hollow cylinder with six ÅspokesÅ at the flared end. In order to understand the detailed association of the macromolecules, it is necessary to do a high resolution structural analysis. Large, single layered arrays of the surface layer protein have been obtained for this purpose by means of extensive heating in high CaCl2, a procedure derived from that of Buckmire and Murray. Low dose, low temperature electron microscopy has been applied to the large arrays.As a first step, the samples were negatively stained with neutralized phosphotungstic acid, and the specimens were imaged at 40,000 magnification by use of a high resolution cold stage on a JE0L 100B. Low dose images were recorded with exposures of 7-9 electrons/Å2. The micrographs obtained (Fig. 1) were examined by use of optical diffraction (Fig. 2) to tell what areas were especially well ordered.

Crystalline order to a resolution of 4.7 A in the sheath of Methanospirilium hungatii: A cross-beta structure

1984 ◽  
Vol 42 ◽  
pp. 214-215
Author(s):  
Murray Stewart ◽  
T.J. Beveridge ◽  
D. Sprott
Keyword(s):  
Cell Wall ◽  
Single Layer ◽  
Uranyl Acetate ◽  
Optical Diffraction ◽  
Tube Axis ◽  
Basic Subunit ◽  
Beta Structure ◽  
Diffraction Patterns ◽  
Protein Treatment ◽  
General Appearance

The archaebacterium Methanospirillum hungatii has a sheath as part of its cell wall which is composed mainly of protein. Treatment with dithiothreitol or NaOH released the intact sheaths and electron micrographs of this material negatively stained with uranyl acetate showed flattened hollow tubes, about 0.5 μm diameter and several microns long, in which the patterns from the top and bottom were superimposed. Single layers, derived from broken tubes, were also seen and were more simply analysed. Figure 1 shows the general appearance of a single layer. There was a faint axial periodicity at 28.5 A, which was stronger at irregular multiples of 28.5 A (3 and 4 times were most common), and fine striations were also seen at about 3° to the tube axis. Low angle electron diffraction patterns (not shown) and optical diffraction patterns (Fig. 2) from these layers showed a complex meridian (as a result of the irregular nature of the repeat along the tube axis) which showed a clear maximum at 28.5 A, consistent with the basic subunit spacing.

Single molecule optical diffraction: A tool for understanding the structure of triple stranded left-hand helical cellulose

1989 ◽  
Vol 47 ◽  
pp. 1024-1025
Author(s):  
George C. Ruben ◽  
William Krakow
Keyword(s):  
Single Molecule ◽  
Helical Structure ◽  
Optical Diffraction ◽  
Maximum Diameter ◽  
Primary Cell Wall ◽  
Cellulose Synthesis ◽  
Left Hand ◽  
Left Handed ◽  
Freeze Dried ◽  
Diffraction Patterns

Tobacco primary cell wall and normal bacterial Acetobacter xylinum cellulose formation produced a 36.8±3Å triple-stranded left-hand helical microfibril in freeze-dried Pt-C replicas and in negatively stained preparations for TEM. As three submicrofibril strands exit the wall of Axylinum , they twist together to form a left-hand helical microfibril. This process is driven by the left-hand helical structure of the submicrofibril and by cellulose synthesis. That is, as the submicrofibril is elongating at the wall, it is also being left-hand twisted and twisted together with two other submicrofibrils. The submicrofibril appears to have the dimensions of a nine (l-4)-ß-D-glucan parallel chain crystalline unit whose long, 23Å, and short, 19Å, diagonals form major and minor left-handed axial surface ridges every 36Å.The computer generated optical diffraction of this model and its corresponding image have been compared. The submicrofibril model was used to construct a microfibril model. This model and corresponding microfibril images have also been optically diffracted and comparedIn this paper we compare two less complex microfibril models. The first model (Fig. 1a) is constructed with cylindrical submicrofibrils. The second model (Fig. 2a) is also constructed with three submicrofibrils but with a single 23 Å diagonal, projecting from a rounded cross section and left-hand helically twisted, with a 36Å repeat, similar to the original model (45°±10° crossover angle). The submicrofibrils cross the microfibril axis at roughly a 45°±10° angle, the same crossover angle observed in microflbril TEM images. These models were constructed so that the maximum diameter of the submicrofibrils was 23Å and the overall microfibril diameters were similar to Pt-C coated image diameters of ∼50Å and not the actual diameter of 36.5Å. The methods for computing optical diffraction patterns have been published before.

The Contribution of Intermediate-Voltage, High-Resolution Electron Microscopy In Materials Science: An Appraisal

1990 ◽  
Vol 48 (1) ◽  
pp. 478-479
Author(s):  
John L. Hutchison
Keyword(s):  
High Resolution ◽  
Materials Science ◽  
High Resolution Electron Microscopy ◽  
Optical Diffraction ◽  
The Past ◽  
Resolution Electron ◽  
Extreme Sensitivity ◽  
Electron Microscopes ◽  
New Generation ◽  
Small Metal Particles

Over the past five years or so the development of a new generation of high resolution electron microscopes operating routinely in the 300-400 kilovolt range has produced a dramatic increase in resolution, to around 1.6 Å for “structure resolution” and approaching 1.2 Å for information limits. With a large number of such instruments now in operation it is timely to assess their impact in the various areas of materials science where they are now being used. Are they falling short of the early expectations? Generally, the manufacturers’ claims regarding resolution are being met, but one unexpected factor which has emerged is the extreme sensitivity of these instruments to both floor-borne and acoustic vibrations. Successful measures to counteract these disturbances may require the use of special anti-vibration blocks, or even simple oil-filled dampers together with springs, with heavy curtaining around the microscope room to reduce noise levels. In assessing performance levels, optical diffraction analysis is becoming the accepted method, with rotational averaging useful for obtaining a good measure of information limits. It is worth noting here that microscope alignment becomes very critical for the highest resolution.In attempting an appraisal of the contributions of intermediate voltage HREMs to materials science we will outline a few of the areas where they are most widely used. These include semiconductors, oxides, and small metal particles, in addition to metals and minerals.

High-Resolution Cryo-Electron Microscopy of Biological Macromolecules

1990 ◽  
Vol 48 (1) ◽  
pp. 126-127
Author(s):  
Yoshinori Fujiyoshi
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Diffraction Pattern ◽  
Superfluid Helium ◽  
Copper Phthalocyanine ◽  
Optical Diffraction ◽  
Irradiation Damage ◽  
Biological Macromolecules ◽  
Cross Sectional ◽  
Instrumental Resolution

The resolution of direct images of biological macromolecules is normally restricted to far less than 0.3 nm. This is not due instrumental resolution, but irradiation damage. The damage to biological macromolecules may expect to be reduced when they are cooled to a very low temperature. We started to develop a new cryo-stage for a high resolution electron microscopy in 1983, and successfully constructed a superfluid helium stage for a 400 kV microscope by 1986, whereby chlorinated copper-phthalocyanine could be photographed to a resolution of 0.26 nm at a stage temperature of 1.5 K. We are continuing to develop the cryo-microscope and have developed a cryo-microscope equipped with a superfluid helium stage and new cryo-transfer device.The New cryo-microscope achieves not only improved resolution but also increased operational ease. The construction of the new super-fluid helium stage is shown in Fig. 1, where the cross sectional structure is shown parallel to an electron beam path. The capacities of LN2 tank, LHe tank and the pot are 1400 ml, 1200 ml and 3 ml, respectively. Their surfaces are placed with gold to minimize thermal radiation. Consumption rates of liquid nitrogen and liquid helium are 170 ml/hour and 140 ml/hour, respectively. The working time of this stage is more than 7 hours starting from full LN2 and LHe tanks. Instrumental resolution of our cryo-stage cooled to 4.2 K was confirmed to be 0.20 nm by an optical diffraction pattern from the image of a chlorinated copper-phthalocyanine crystal. The image and the optical diffraction pattern are shown in Fig. 2 a, b, respectively.

Reconstruction of Chitin-Protein Complexes Using Correlation Averaging Methods: Ovipositor of the Ichneumon Fly Megarhyssa

1980 ◽  
Vol 38 ◽  
pp. 38-39
Author(s):  
L. T. Germinario ◽  
J. Blackwell ◽  
J. Frank
Keyword(s):  
Protein Complexes ◽  
Hexagonal Lattice ◽  
Uranyl Acetate ◽  
Optical Diffraction ◽  
Insect Cuticle ◽  
High Dose ◽  
Wide Angle ◽  
X Ray ◽  
Averaging Methods ◽  
Digital Correlation

This report describes the use of digital correlation and averaging methods 1,2 for the reconstruction of high dose electron micrographs of the chitin-protein complex from Megarhyssa ovipositor. Electron microscopy of uranyl acetate stained insect cuticle has demonstrated a hexagonal array of unstained chitin monofibrils, 2.4−3.0 nm in diameter, in a stained protein matrix3,4. Optical diffraction Indicated a hexagonal lattice with a = 5.1-8.3 nm3 A particularly well ordered complex is found in the ovipositor of the ichneumon fly Megarhyssa: the small angle x-ray data gives a = 7.25 nm, and the wide angle pattern shows that the protein consists of subunits arranged in a 61 helix, with an axial repeat of 3.06 nm5.

Sign in / Sign up

Export Citation Format

Share Document