Biomechanics of Skateboarding: Kinetics of the Ollie

2006 ◽  
Vol 22 (1) ◽  
pp. 33-40 ◽  
Author(s):  
Edward C. Frederick ◽  
Jeremy J. Determan ◽  
Saunders N. Whittlesey ◽  
Joseph Hamill

Seven top amateur or professional skateboarders (BW = 713 N ± 83 N) performed Ollie maneuvers onto and off an elevated wooden platform (45.7 cm high). We recorded ground reaction force (GRF) data for three Ollie Up (OU) and Ollie Down (OD) trials per participant. The vertical GRF (VGRF) during the OU has a characteristic propulsive peak (M = 2.22 body weight [BW] ± 0.22) resulting from rapidly rotating the tail of the board into the ground to propel the skater and board up and forward. The anterior-posterior (A-P) GRF also shows a pronounced peak (M = 0.05 ± 0.01 BW) corresponding with this propulsive VGRF peak. The initial phase of landing in the OD shows an impact peak in VGRF rising during the first 30 to 80 ms to a mean of 4.74 ± 0.46 BW. These impact peaks are higher than expected given the relatively short drop of 45.7 cm and crouched body position. But we observed that our participants intentionally affected a firm landing to stabilize the landing position; and the Ollie off the platform raised the center of mass, also contributing to higher forces.

2000 ◽  
Vol 203 (23) ◽  
pp. 3585-3594 ◽  
Author(s):  
J. Liao ◽  
G.V. Lauder

Basal ray-finned fishes possess a heterocercal tail in which the dorsal lobe containing the extension of the vertebral column is longer than the ventral lobe. Clarifying the function of the heterocercal tail has proved elusive because of the difficulty of measuring the direction of force produced relative to body position in the aquatic medium. We measured the direction of force produced by the heterocercal tail of the white sturgeon (Acipenser transmontanus) by visualizing flow in the wake of the tail using digital particle image velocimetry (DPIV) while simultaneously recording body position and motion using high-speed video. To quantify tail function, we measured the vertical body velocity, the body angle and the path angle of the body from video recordings and the vortex ring axis angle and vortex jet angle from DPIV recordings of the wake downstream from the tail. These variables were measured for sturgeon exhibiting three swimming behaviors at 1.2 L s(−)(1), where L is total body length: rising through the water column, holding vertical position, and sinking through the water column. For vertical body velocity, body angle and path angle values, all behaviors were significantly different from one another. For vortex ring axis angle and vortex jet angle, rising and holding behavior were not significantly different from each other, but both were significantly different from sinking behavior. During steady horizontal swimming, the sturgeon tail generates a lift force relative to the path of motion but no rotational moment because the reaction force passes through the center of mass. For a rising sturgeon, the tail does not produce a lift force but causes the tail to rotate ventrally in relation to the head since the reaction force passes ventral to the center of mass. While sinking, the direction of the fluid jet produced by the tail relative to the path of motion causes a lift force to be created and causes the tail to rotate dorsally in relation to the head since the reaction force passes dorsal to the center of mass. These data provide evidence that sturgeon can actively control the direction of force produced by their tail while maneuvering through the water column because the relationship between vortex jet angle and body angle is not constant.


Author(s):  
Wei-Hsun Tai ◽  
Ray-Hsien Tang ◽  
Chen-Fu Huang ◽  
Shin-Liang Lo ◽  
Yu-Chi Sung ◽  
...  

The study aimed to investigate the acute effects of handheld loading on standing broad jump (SBJ) performance and biomechanics. Fifteen youth male athletes (mean age: 14.7 ± 0.9 years; body mass: 59.3 ± 8.0 kg; height: 1.73 ± 0.07 m) volunteered to participate in the study. Participants were assigned to perform SBJ with and without 4 kg dumbbells in a random order. Kinematic and kinetic data were collected using 10 infrared high-speed motion-capture cameras at a 250 Hz sampling rate and two force platforms at a 1000 Hz sampling rate. A paired t-test was applied to all variables to determine the significance between loading and unloading SBJs. Horizontal distance (p < 0.001), take-off distance (p = 0.001), landing distance (p < 0.001), horizontal velocity of center of mass (CoM; p < 0.001), push time (p < 0.001), vertical impulse (p = 0.003), and peak horizontal and vertical ground reaction force (GRF; p < 0.001, p = 0.017) were significantly greater in loading SBJ than in unloading SBJ. The take-off vertical velocity of CoM (p = 0.001), take-off angle (p < 0.001), peak knee and hip velocity (p < 0.001, p = 0.007), peak ankle and hip moment (p = 0.006, p = 0.011), and peak hip power (p = 0.014) were significantly greater in unloading SBJ than in loading SBJ. Conclusions: Acute enhancement in SBJ performance was observed with handheld loading. The present findings contribute to the understanding of biomechanical differences in SBJ performance with handheld loading and are highly applicable to strength and conditioning training for athletes.


Author(s):  
Katherine Boyer ◽  
Jonathan Rylander ◽  
Thomas Andriacchi ◽  
Gary Beaupre

Walking programs provide an attractive intervention to address the preservation of bone mass in the aging population. Research suggests one in three women and one in five men over 50 will experience fractures due to osteoporosis [1,2]. Bone is a mechanically modulated tissue and thus, training programs that prescribe physical activities that dynamically load the skeleton through either muscle contractions (strength training) or locomotion (walking/running) would be expected to have a positive influence on bone mineral density (BMD) preservation. However, attempts to implement activity programs in populations at risk for developing osteoporosis to accrue or simply preserve bone mass have had limited success [3] due to a variable response between subjects. It has been suggested that the failure of these programs to significantly influence bone mass or density may be due to individual differences in the loads generated by the prescribed exercise regimes and/or the knowledge of specific types, intensities and volumes needed for effective osteogenic exercise. Walking, a simple, common activity, presents an interesting opportunity to examine the potential for individual differences in the style of walking to explain the variability in individual results to training programs designed to preserve bone density.


2002 ◽  
Vol 205 (10) ◽  
pp. 1485-1494 ◽  
Author(s):  
Thomas J. Roberts ◽  
Jeffrey A. Scales

SUMMARYWe tested the hypothesis that the hindlimb muscles of wild turkeys(Meleagris gallopavo) can produce maximal power during running accelerations. The mechanical power developed during single running steps was calculated from force-plate and high-speed video measurements as turkeys accelerated over a trackway. Steady-speed running steps and accelerations were compared to determine how turkeys alter their running mechanics from a low-power to a high-power gait. During maximal accelerations, turkeys eliminated two features of running mechanics that are characteristic of steady-speed running: (i) they produced purely propulsive horizontal ground reaction forces, with no braking forces, and (ii) they produced purely positive work during stance, with no decrease in the mechanical energy of the body during the step. The braking and propulsive forces ordinarily developed during steady-speed running are important for balance because they align the ground reaction force vector with the center of mass. Increases in acceleration in turkeys correlated with decreases in the angle of limb protraction at toe-down and increases in the angle of limb retraction at toe-off. These kinematic changes allow turkeys to maintain the alignment of the center of mass and ground reaction force vector during accelerations when large propulsive forces result in a forward-directed ground reaction force. During the highest accelerations, turkeys produced exclusively positive mechanical power. The measured power output during acceleration divided by the total hindlimb muscle mass yielded estimates of peak instantaneous power output in excess of 400 W kg-1 hindlimb muscle mass. This value exceeds estimates of peak instantaneous power output of turkey muscle fibers. The mean power developed during the entire stance phase increased from approximately zero during steady-speed runs to more than 150 W kg-1muscle during the highest accelerations. The high power outputs observed during accelerations suggest that elastic energy storage and recovery may redistribute muscle power during acceleration. Elastic mechanisms may expand the functional range of muscle contractile elements in running animals by allowing muscles to vary their mechanical function from force-producing struts during steady-speed running to power-producing motors during acceleration.


2004 ◽  
Vol 13 (2) ◽  
pp. 135-150 ◽  
Author(s):  
Scott Ross ◽  
Kevin Guskiewicz ◽  
William Prentice ◽  
Robert Schneider ◽  
Bing Yu

Objective:T o determine differences between contralateral limbs’ strength, proprio-ception, and kinetic and knee-kinematic variables during single-limb landing.Setting:Laboratory.Subjects:30.Measurements:Hip, knee, and foot isokinetic peak torques; anterior/posterior (AP) and medial/lateral (ML) sway displacements during a balance task; and stabilization times, vertical ground-reaction force (VGRF), time to peak VGRF, and knee-flexion range of motion (ROM) from initial foot contact to peak VGRF during single-limb landing.Results:The kicking limb had significantly greater values for knee-extension (P= .008) and -flexion (P= .047) peak torques, AP sway displacement (P= .010), knee-flexion ROM from initial foot contact to peak VGRF (P< .001), and time to peak VGRF (P= .004). No other dependent measures were significantly different between limbs (P> .05).Conclusion:The kicking limb had superior thigh strength, better proprioception, and greater knee-flexion ROM than the stance limb.


2007 ◽  
Vol 293 (2) ◽  
pp. C797-C804 ◽  
Author(s):  
R. Gerometta ◽  
A. C. Zamudio ◽  
D. P. Escobar ◽  
O. A. Candia

During accommodation, mammalian lenses change shape from a rounder configuration (near focusing) to a flatter one (distance focusing). Thus the lens must have the capacity to change its volume, capsular surface area, or both. Because lens topology is similar to a torus, we developed an approach that allows volume determination from the lens cross-sectional area (CSA). The CSA was obtained from photographs taken perpendicularly to the lenticular anterior-posterior (A-P) axis and computed with software. We calculated the volume of isolated bovine lenses in conditions simulating accommodation by forcing shape changes with a custom-built stretching device in which the ciliary body-zonulae-lens complex (CB-Z-L) was placed. Two measurements were taken (CSA and center of mass) to calculate volume. Mechanically stretching the CB-Z-L increased the equatorial length and decreased the A-P length, CSA, and lens volume. The control parameters were restored when the lenses were stretched and relaxed in an aqueous physiological solution, but not when submerged in oil, a condition with which fluid leaves the lens and does not reenter. This suggests that changes in lens CSA previously observed in humans could have resulted from fluid movement out of the lens. Thus accommodation may involve changes not only in capsular surface but also in volume. Furthermore, we calculated theoretical volume changes during accommodation in models of human lenses using published structural parameters. In conclusion, we suggest that impediments to fluid flow between the aquaporin-rich lens fibers and the lens surface could contribute to the aging-related loss of accommodative power.


PLoS ONE ◽  
2020 ◽  
Vol 15 (12) ◽  
pp. e0242215
Author(s):  
A. M. van Leeuwen ◽  
J. H. van Dieën ◽  
A. Daffertshofer ◽  
S. M. Bruijn

Step-by-step foot placement control, relative to the center of mass (CoM) kinematic state, is generally considered a dominant mechanism for maintenance of gait stability. By adequate (mediolateral) positioning of the center of pressure with respect to the CoM, the ground reaction force generates a moment that prevents falling. In healthy individuals, foot placement is complemented mainly by ankle moment control ensuring stability. To evaluate possible compensatory relationships between step-by-step foot placement and complementary ankle moments, we investigated the degree of (active) foot placement control during steady-state walking, and under either foot placement-, or ankle moment constraints. Thirty healthy participants walked on a treadmill, while full-body kinematics, ground reaction forces and EMG activities were recorded. As a replication of earlier findings, we first showed step-by-step foot placement is associated with preceding CoM state and hip ab-/adductor activity during steady-state walking. Tight control of foot placement appears to be important at normal walking speed because there was a limited change in the degree of foot placement control despite the presence of a foot placement constraint. At slow speed, the degree of foot placement control decreased substantially, suggesting that tight control of foot placement is less essential when walking slowly. Step-by-step foot placement control was not tightened to compensate for constrained ankle moments. Instead compensation was achieved through increases in step width and stride frequency.


2021 ◽  
Author(s):  
Andrej Olenšek ◽  
Matjaž Zadravec ◽  
Helena Burger ◽  
Zlatko Matjačić

Abstract BackgroundDue to disrupted motor and proprioceptive function lower limb amputation imposes considerable challenges associated with balance and greatly increases risk of falling in case of perturbations during walking. The aim of this study was to investigate dynamic balancing responses in unilateral transtibial amputees when they were subjected to perturbing pushes to the pelvis in outward direction at the time of foot strike on non-amputated and amputated side during slow walking.MethodsFourteen subjects with unilateral transtibial amputation and nine control subjects participated in the study. They were subjected to perturbations that were delivered to the pelvis at the time of foot strike of either the left or right leg. We recorded trajectories of center of pressure and center of mass, durations of in-stance and stepping periods as well as ground reaction forces. Statistical analysis was performed to determine significant differences in dynamic balancing responses between control subjects and subjects with amputation when subjected to outward-directed perturbation upon entering stance phases with non-amputated or amputated side.ResultsWhen outward-directed perturbations were delivered at the time of foot strike of the non-amputated leg, subjects with amputation were able to modulate center of pressure and ground reaction force similarly as control subjects which indicates application of in-stance balancing strategies. On the other hand, there was a complete lack of in-stance response when perturbations were delivered when the amputated leg entered the stance phase. Subjects with amputations instead used the stepping strategy and adjusted placement of the non-amputated leg in the ensuing stance phase to make a cross-step. Such response resulted in significantly higher displacement of center of mass. ConclusionsResults of this study suggest that due to the absence of the COP modulation mechanism, which is normally supplied by ankle motor function, people with unilateral transtibial amputation are compelled to choose the stepping strategy over in-stance strategy when they are subjected to outward-directed perturbation on the amputated side. However, the stepping response is less efficient than in-stance response. To improve their balancing responses to unexpected balance perturbation people fitted with passive transtibial prostheses should undergo perturbation-based balance training during clinical rehabilitation.


2013 ◽  
Vol 29 (1) ◽  
pp. 55-60 ◽  
Author(s):  
Hiroaki Hobara ◽  
Koh Inoue ◽  
Kazuyuki Kanosue

Understanding the degree of leg stiffness during human movement would provide important information that may be used for injury prevention. In the current study, we investigated bilateral differences in leg stiffness during one-legged hopping. Ten male participants performed one-legged hopping in place, matching metronome beats at 1.5, 2.2, and 3.0 Hz. Based on a spring-mass model, we calculated leg stiffness, which is defined as the ratio of maximal ground reaction force to maximum center of mass displacement at the middle of the stance phase, measured from vertical ground reaction force. In all hopping frequency settings, there was no significant difference in leg stiffness between legs. Although not statistically significant, asymmetry was the greatest at 1.5 Hz, followed by 2.2 and 3.0 Hz for all dependent variables. Furthermore, the number of subjects with an asymmetry greater than the 10% criterion was larger at 1.5 Hz than those at 2.2 and 3.0 Hz. These results will assist in the formulation of treatment-specific training regimes and rehabilitation programs for lower extremity injuries.


Sign in / Sign up

Export Citation Format

Share Document