Wideband Input Matching CMOS Low-Noise Amplifier with Noise and Distortion Cancellation

2019 ◽  
Vol 29 (04) ◽  
pp. 2050059
Author(s):  
Asieh Parhizkar Tarighat ◽  
Mostafa Yargholi
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Modified Technique ◽  
Input Matching ◽  
Noise Cancelling ◽  
Resistive Feedback ◽  
Noise Amplifier

In this paper, a wideband low-noise amplifier (LNA) is designed based on the resistive feedback topology with a TSMC 0.18[Formula: see text][Formula: see text]m standard RF CMOS process. Bandwidth expansion is provided by the second-order Chebyshev filter. The noise figure (NF) increases at high frequency because of the source parasitic capacitors of the cascode transistor; so, noise cancelling technique is applied to the cascode transistor of the proposed LNA. Bias conditions and sizes of the transistors are optimized to cancel the nonlinear transconductance ([Formula: see text]). With this modified technique, low noise figure, high linearity and improved input and output matching can be attained for 3.1–10.6[Formula: see text]GHz frequency band. Post-layout simulation result of the proposed LNA shows the maximum power gain of 17[Formula: see text]dB at 5.5[Formula: see text]GHz frequency, NF of lower than 4.5[Formula: see text]dB over the whole band of 3.1–10.6[Formula: see text]GHz, maximum IIP2 of [Formula: see text]28[Formula: see text]dBm and IIP3 of [Formula: see text]7.5[Formula: see text]dBm, while dissipating 9[Formula: see text]mW (with buffer) from a 1.8 V supply voltage. It occupies [Formula: see text]m silicon die area.

Optimized Design of Low Power Complementary Metal Oxide Semiconductor Low Noise Amplifier for Zigbee Application

2021 ◽  
Vol 18 (4) ◽  
pp. 1327-1330
Author(s):  
S. Manjula ◽  
R. Karthikeyan ◽  
S. Karthick ◽  
N. Logesh ◽  
M. Logeshkumar
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Oxide Semiconductor ◽  
Design System ◽  
Cmos Process ◽  
Design Specifications ◽  
Noise Amplifier

An optimized high gain low power low noise amplifier (LNA) is presented using 90 nm CMOS process at 2.4 GHz frequency for Zigbee applications. For achieving desired design specifications, the LNA is optimized by particle swarm optimization (PSO). The PSO is successfully implemented for optimizing noise figure (NF) when satisfying all the design specifications such as gain, power dissipation, linearity and stability. PSO algorithm is developed in MATLAB to optimize the LNA parameters. The LNA with optimized parameters is simulated using Advanced Design System (ADS) Simulator. The LNA with optimized parameters produces 21.470 dB of voltage gain, 1.031 dB of noise figure at 1.02 mW power consumption with 1.2 V supply voltage. The comparison of designed LNA with and without PSO proves that the optimization improves the LNA results while satisfying all the design constraints.

A FULLY INTEGRATED MULTIBAND CMOS 0.35 μM LNA FOR IEEE802.16 STANDARD

2013 ◽  
Vol 22 (02) ◽  
pp. 1250088 ◽  
Author(s):  
MERIAM BEN AMOR ◽  
MOURAD LOULOU ◽  
SEBASTIEN QUINTANEL ◽  
DANIEL PASQUET
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Wide Band ◽  
Low Noise ◽  
Cmos Process ◽  
Frequency Range ◽  
Fully Integrated ◽  
Input Matching ◽  
Noise Amplifier ◽  
Chebyshev Filter

In this paper we present the design of a fully integrated low noise amplifier for WiMAX standard with AMS 0.35 μm CMOS process. This LNA is designed to cover the frequency range for licensed and unlicensed bands of the WiMAX 2.3–5.9 GHz. The proposed amplifier achieves a wide band input and output matching with S11 and S22 lower than -10 dB, a flat gain of 12 dB and a noise figure around 3.5 dB for the entire band and from the upper to the higher frequencies. The presented wide band LNA employs a Chebyshev filter for input matching and an inductive shunt feedback for output matching with a bias current of 15 mA and a supply voltage of 2.5 V.

An ESD Protected Wideband CMOS Low Noise Amplifier Employing Active Feedback Technique

2011 ◽  
Vol 403-408 ◽  
pp. 2809-2813
Author(s):  
Kuan Bao ◽  
Xiang Ning Fan
Keyword(s):  
Noise Figure ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Fully Integrated ◽  
Input Matching ◽  
Active Feedback ◽  
Cmos Lna ◽  
Noise Amplifier ◽  
On Chip

This paper presents a wideband low noise amplifier (LNA) for multi-standard radio applications. The low noise characteristic and input matching are simultaneously achieved by active-feedback technique. Bond-wire inductors and electrostatic devices (ESDs) are co-designed to improve the chip performance. Implemented in 0.18-μm CMOS process, the core size of the fully integrated LNA circuits is 535 μm×425 μm without any passive on-chip inductor. The simulated gain and the minimal noise figure of the CMOS LNA are 17.5 dB and 2.0 dB, respectively. The LNA achieves a -3dB bandwidth of 3.1 GHz. And the simulated IIP3 is -4.4 dBm at 2.5 GHz. Operating at 1.8V, the LNA draws a current of 7.7 mA.

A MULTI-BAND LOW NOISE AMPLIFIER WITH GAIN FLATNESS AND BANDWIDTH ENHANCEMENT

2014 ◽  
Vol 23 (02) ◽  
pp. 1450017 ◽  
Author(s):  
SAN-FU WANG ◽  
JAN-OU WU ◽  
YANG-HSIN FAN ◽  
JHEN-JI WANG
Keyword(s):  
Performance Enhancement ◽  
Supply Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Bandwidth Enhancement ◽  
Input Matching ◽  
Noise Amplifier ◽  
Tunable Frequency ◽  
Multi Band

In this paper, a differential multi-band CMOS low noise amplifier (LNA) is proposed that is operated within a range of 1500–2700 MHz with input matching capacitor switching and gain flatness performance enhancement technique. Traditional multi-band LNAs have poor performances on gain flatness performance. Therefore, we propose a new multi-band LNA which obtain good gain flatness performance by integrating the characteristics of the transistor trans-conductance and LC resonant load. The new LNA can also achieve a tunable frequency at different matching capacitance conditions. The post-layout simulation results shows that the voltage gain is between 19.3 dB and 22.4 dB, the NF is less than 2.5 dB, and the 1-dB compression point is about -5.1 dBm. The LNA consumes 17.79 mW under 1.8 V supply voltage in TSMC 0.18-um RF CMOS process.

Design of a Capacitor Cross-Coupled Common Gate Wideband Low Noise Amplifier with Noise Canceling Technique

2014 ◽  
Vol 618 ◽  
pp. 548-552
Author(s):  
Dan Song ◽  
Xiang Ning Fan ◽  
Kuan Bao ◽  
Zai Jun Hua
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Drain Current ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Noise Characteristic ◽  
Cmos Process ◽  
Common Gate ◽  
Noise Amplifier ◽  
Noise Canceling

This paper presents a wideband low noise amplifier (LNA) for multi-standard radio application .The low noise amplifier achieves wideband matching with the structure of differential common gate .Meanwhile ,the low noise characteristic is achieved by noise canceling and capacitor cross-coupled. Fabricated in 0.18μm CMOS process, the LNA is designed to operate from 700MHz to 2.6GHz.As are shown in the results of simulation, when the LNA operates from 700MHz to 2.6GHz,the S11 is less than-10dB,the gain achieves 8.5 dB and the variation is within ±0.5dB.The noise figure is 2.2dB wih the supply voltage is 1.8v and the drain current is 8mA.

Design of 3.1-10.6GHz CMOS LNA Based on Input Matching Technique of Common-Gate Topology

2013 ◽  
Vol 479-480 ◽  
pp. 1014-1017
Author(s):  
Yi Cheng Chang ◽  
Meng Ting Hsu ◽  
Yu Chang Hsieh
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Average Power ◽  
Wide Band ◽  
Low Noise ◽  
Input Matching ◽  
Common Gate ◽  
Cmos Lna ◽  
Noise Amplifier ◽  
Is Design

In this study, three stage ultra-wide-band CMOS low-noise amplifier (LNA) is presented. The UWB LNA is design in 0.18μm TSMC CMOS technique. The LNA input and output return loss are both less than-10dB, and achieved 10dB of average power gain, the minimum noise figure is 6.55dB, IIP3 is about-9.5dBm. It consumes 11mW from a 1.0-V supply voltage.

Design of Low-Noise Two-Path Amplifier for 6–16 GHz Applications

2020 ◽  
pp. 2150136
Author(s):  
Asieh Parhizkar Tarighat ◽  
Mostafa Yargholi
Keyword(s):  
Noise Figure ◽  
Impedance Matching ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Input Matching ◽  
Inductive Peaking ◽  
Linearity Improvement ◽  
Noise Amplifier ◽  
Path Structure

A two-path low-noise amplifier (LNA) is designed with TSMC 0.18[Formula: see text][Formula: see text]m standard RF CMOS process for 6–16[Formula: see text]GHz frequency band applications. The principle of a conventional resistive shunt feedback LNA is analyzed to demonstrate the trade-off between the noise figure (NF) and the input matching. To alleviate the mentioned issue for wideband application, this structure with noise canceling technique and linearity improvement are applied to a two-path structure. Flat and high gain is supplied by the primary path; while the input and output impedance matching are provided by the secondary path. The [Formula: see text][Formula: see text]dB bandwidth can be increased to a higher frequency by inductive peaking, which is used at the first stage of the two paths. Besides, by biasing the transistors at the threshold voltage, low power dissipation is achieved. The [Formula: see text][Formula: see text]dB gain bandwidth of the proposed LNA is 10[Formula: see text]GHz, while the maximum power gain of 13.1[Formula: see text]dB is attained. With this structure, minimum NF of 4.6[Formula: see text]dB and noise flatness of 1[Formula: see text]dB in the whole bandwidth can be achieved. The input impedance is matched, and S[Formula: see text] is lower than [Formula: see text]10 dB. With the proposed linearized LNA, the average IIP[Formula: see text][Formula: see text]dBm is gained, while it occupies 1051.7[Formula: see text][Formula: see text]m die area.

STUDY OF PARASITIC CAPACITANCE EFFECT ON NOISE FIGURE OF IDCLNA IN DEEP SUBMICRON CMOS TECHNOLOGIES

2014 ◽  
Vol 23 (05) ◽  
pp. 1450058
Author(s):  
S. MANJULA ◽  
D. SELVATHI
Keyword(s):  
Noise Figure ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Current Gain ◽  
Cmos Process ◽  
Short Channel ◽  
Trade Offs ◽  
Noise Amplifier ◽  
The Impact

Low noise amplifier (LNA) is an important component in RF receiver front end. An inductively degenerated cascode low noise amplifier (IDCLNA) is mostly preferred for producing good trade-offs such as high gain, low noise figure (NF), high reverse isolation and low power consumption for narrowband applications. This IDCLNA structure is also used to reduce the gate induced noise on the noise performance by inserting the capacitance in parallel with the gate-to-source capacitance of main transistor. Usually, the parasitic overlap capacitances can impose serious constraints on achievable performance and is taken into account in IDCLNA. In this paper, IDCLNA is designed at a frequency of 2.4 GHz with analyzing the impact of parasitic overlap capacitances on IDCLNA in terms of unity current gain frequency (f T ) which will affect the NF of IDCLNA and simulated using 130 nm, 90 nm and 65 nm CMOS technologies. The NF of IDCLNA with and without parasitic overlap capacitances are analyzed and compared for different short channel CMOS processes. Simulation results show that the parasitic overlap capacitances have advantageous to reduce the gate induced noise in IDCLNA for 130-nm CMOS process for 2.4 GHz applications.

Low-power CMOS LNA based on dual resistive-feedback structure with peaking inductor for wideband application

2013 ◽  
Vol 5 (1) ◽  
pp. 65-70 ◽  
Author(s):  
Meng-Ting Hsu ◽  
Shih-Yu Hsu ◽  
Yu-Hwa Lin
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Low Noise ◽  
Cmos Process ◽  
Output Stage ◽  
Chip Area ◽  
Inductive Peaking ◽  
Resistive Feedback ◽  
Low Power Cmos ◽  
Noise Amplifier

This paper presents a low-power and low-noise amplifier (LNA) with resistive-feedback configuration. The design consists of two resistive-feedback amplifiers. In order to reduce the chip area, a resistive-feedback inverter is adopted for input matching. The output stage adopts basic topology of an RC feedback for output matching, and adds two inductors for inductive peaking at the high band. The implemented LNA has a peak gain of 10.5 dB, the input reflection coefficient S11 is lower than −8 dB and the output reflection S22 is lower than −10.8 dB, and noise figure of 4.2–5.2 dB is between 1 and 10 GHz while consuming 12.65 mW from a 1.5 V supply. The chip area is only 0.69 mm2 and the figure of merit is 6.64 including the area estimation. The circuit was fabricated in a TSMC 0.18 um CMOS process.

Sign in / Sign up

Export Citation Format

Share Document