Low-power CMOS LNA based on dual resistive-feedback structure with peaking inductor for wideband application

2013 ◽  
Vol 5 (1) ◽  
pp. 65-70 ◽  
Author(s):  
Meng-Ting Hsu ◽  
Shih-Yu Hsu ◽  
Yu-Hwa Lin
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Low Noise ◽  
Cmos Process ◽  
Output Stage ◽  
Chip Area ◽  
Inductive Peaking ◽  
Resistive Feedback ◽  
Low Power Cmos ◽  
Noise Amplifier

This paper presents a low-power and low-noise amplifier (LNA) with resistive-feedback configuration. The design consists of two resistive-feedback amplifiers. In order to reduce the chip area, a resistive-feedback inverter is adopted for input matching. The output stage adopts basic topology of an RC feedback for output matching, and adds two inductors for inductive peaking at the high band. The implemented LNA has a peak gain of 10.5 dB, the input reflection coefficient S11 is lower than −8 dB and the output reflection S22 is lower than −10.8 dB, and noise figure of 4.2–5.2 dB is between 1 and 10 GHz while consuming 12.65 mW from a 1.5 V supply. The chip area is only 0.69 mm2 and the figure of merit is 6.64 including the area estimation. The circuit was fabricated in a TSMC 0.18 um CMOS process.

scholarly journals Design of Low Power UWB CMOS Low Noise Amplifier using Active Inductor for WLAN Receiver

2018 ◽  
Vol 7 (2.24) ◽  
pp. 448
Author(s):  
S Manjula ◽  
M Malleshwari ◽  
M Suganthy
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Wide Band ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Design System ◽  
Active Inductor ◽  
Chip Area ◽  
Noise Amplifier

This paper presents a low power Low Noise Amplifier (LNA) using 0.18µm CMOS technology for ultra wide band (UWB) applications. gm boosting common gate (CG) LNA is designed to improve the noise performance.  For the reduction of on chip area, active inductor is employed at the input side of the designed LNA for input impedance matching. The proposed UWB LNA is designed using Advanced Design System (ADS) at UWB frequency of 3.1-10.6 GHz. Simulation results show that the gain of 10.74+ 0.01 dB, noise figure is 4.855 dB, input return loss <-13 dB and 12.5 mW power consumption.  

Design of Low-Noise Two-Path Amplifier for 6–16 GHz Applications

2020 ◽  
pp. 2150136
Author(s):  
Asieh Parhizkar Tarighat ◽  
Mostafa Yargholi
Keyword(s):  
Noise Figure ◽  
Impedance Matching ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Input Matching ◽  
Inductive Peaking ◽  
Linearity Improvement ◽  
Noise Amplifier ◽  
Path Structure

A two-path low-noise amplifier (LNA) is designed with TSMC 0.18[Formula: see text][Formula: see text]m standard RF CMOS process for 6–16[Formula: see text]GHz frequency band applications. The principle of a conventional resistive shunt feedback LNA is analyzed to demonstrate the trade-off between the noise figure (NF) and the input matching. To alleviate the mentioned issue for wideband application, this structure with noise canceling technique and linearity improvement are applied to a two-path structure. Flat and high gain is supplied by the primary path; while the input and output impedance matching are provided by the secondary path. The [Formula: see text][Formula: see text]dB bandwidth can be increased to a higher frequency by inductive peaking, which is used at the first stage of the two paths. Besides, by biasing the transistors at the threshold voltage, low power dissipation is achieved. The [Formula: see text][Formula: see text]dB gain bandwidth of the proposed LNA is 10[Formula: see text]GHz, while the maximum power gain of 13.1[Formula: see text]dB is attained. With this structure, minimum NF of 4.6[Formula: see text]dB and noise flatness of 1[Formula: see text]dB in the whole bandwidth can be achieved. The input impedance is matched, and S[Formula: see text] is lower than [Formula: see text]10 dB. With the proposed linearized LNA, the average IIP[Formula: see text][Formula: see text]dBm is gained, while it occupies 1051.7[Formula: see text][Formula: see text]m die area.

Optimized Design of Low Power Complementary Metal Oxide Semiconductor Low Noise Amplifier for Zigbee Application

2021 ◽  
Vol 18 (4) ◽  
pp. 1327-1330
Author(s):  
S. Manjula ◽  
R. Karthikeyan ◽  
S. Karthick ◽  
N. Logesh ◽  
M. Logeshkumar
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Oxide Semiconductor ◽  
Design System ◽  
Cmos Process ◽  
Design Specifications ◽  
Noise Amplifier

An optimized high gain low power low noise amplifier (LNA) is presented using 90 nm CMOS process at 2.4 GHz frequency for Zigbee applications. For achieving desired design specifications, the LNA is optimized by particle swarm optimization (PSO). The PSO is successfully implemented for optimizing noise figure (NF) when satisfying all the design specifications such as gain, power dissipation, linearity and stability. PSO algorithm is developed in MATLAB to optimize the LNA parameters. The LNA with optimized parameters is simulated using Advanced Design System (ADS) Simulator. The LNA with optimized parameters produces 21.470 dB of voltage gain, 1.031 dB of noise figure at 1.02 mW power consumption with 1.2 V supply voltage. The comparison of designed LNA with and without PSO proves that the optimization improves the LNA results while satisfying all the design constraints.

scholarly journals Research and Design of X-band Low Noise Amplifier Based on CMOS Process

2021 ◽  
Vol 2108 (1) ◽  
pp. 012102
Author(s):  
Chao Ma ◽  
Hongjiang Wu ◽  
Xudong Lu ◽  
Haitao Sun
Keyword(s):  
Noise Figure ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Center Frequency ◽  
Cmos Process ◽  
Actual Measurement ◽  
Chip Area ◽  
Chip Size ◽  
Noise Amplifier ◽  
Stage Matching

Abstract Based on CMOS process, a low noise amplifier(LNA) operating at 7.4GHz~11.4GHz was designed. The two-stage differential cascode structure is adopted. Transformer was used to achieve inter-stage matching. Balun was used to achieve input and output matching, which reduces the number of inductors used, effectively reduces the chip size while ensuring good gain and noise figure. The actual measurement results show that the power gain at the center frequency of 9.4GHz is 27dB, the maximum noise figure is less than 3.82dB, the output power 1dB compression point is greater than 8dBm, the chip area is only 0.41mm×0.83mm(excluding PAD).

A Low Power SiGe-BiCMOS LNA for COMPASS Applications

2014 ◽  
Vol 513-517 ◽  
pp. 4580-4584
Author(s):  
Bing Liang Yu ◽  
Jin Li ◽  
Wen Yuan Li
Keyword(s):  
Low Power ◽  
Power Supply ◽  
Noise Figure ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Power Gain ◽  
Bicmos Technology ◽  
Sige Bicmos ◽  
Resistive Feedback ◽  
Noise Amplifier

A novel low-noise amplifier (LNA) suitable for COMPASS receiver applications is designed in SiGe-BiCMOS technology. Inductively degenerated technique and resistive feedback technique are employed to reduce the noise figure. With 1.8V power supply, the measured results achieve 17.23dB power gain and 2.58dB noise figure at 1.561GHz.

scholarly journals A Low-Noise Amplifier Utilizing Current-Reuse Technique and Active Shunt Feedback for MedRadio Band Applications

2020 ◽  
pp. 306-316
Author(s):  
Mutanizam Abdul Mubin ◽  
◽  
Arjuna Marzuki
Keyword(s):  
Low Power ◽  
Return Loss ◽  
Noise Figure ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Common Source ◽  
Cmos Process ◽  
Current Reuse ◽  
Noise Amplifier

In this work, a low-power 0.18-μm CMOS low-noise amplifier (LNA) for MedRadio applications has been designed and verified. Cadence IC5 software with Silterra’s C18G CMOS Process Design Kit were used for all design and simulation work. This LNA utilizes complementary common-source current-reuse topology and subthreshold biasing to achieve low-power operation with simultaneous high gain and low noise figure. An active shunt feedback circuit is used as input matching network to provide a suitable input return loss. For test and measurement purpose, an output buffer was designed and integrated with this LNA. Inductorless design approach of this LNA, together with the use of MOSCAPs as capacitors, help to minimize the die size. On post-layout simulations with LNA die area of 0.06 mm2 and simulated total DC power consumption of 0.5 mW, all targeted specifications are met. The simulated gain, input return loss and noise figure of this LNA are 16.3 dB, 10.1 dB and 4.9 dB respectively throughout the MedRadio frequency range. For linearity, the simulated input-referred P1dB of this LNA is -26.7 dBm while its simulated IIP3 is -18.6 dBm. Overall, the post-layout simulated performance of this proposed LNA is fairly comparable to some current state-of-the-art LNAs for MedRadio applications. The small die area of this proposed LNA is a significant improvement in comparison to those of the previously reported MedRadio LNAs.

Wideband Input Matching CMOS Low-Noise Amplifier with Noise and Distortion Cancellation

2019 ◽  
Vol 29 (04) ◽  
pp. 2050059
Author(s):  
Asieh Parhizkar Tarighat ◽  
Mostafa Yargholi
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Modified Technique ◽  
Input Matching ◽  
Noise Cancelling ◽  
Resistive Feedback ◽  
Noise Amplifier

In this paper, a wideband low-noise amplifier (LNA) is designed based on the resistive feedback topology with a TSMC 0.18[Formula: see text][Formula: see text]m standard RF CMOS process. Bandwidth expansion is provided by the second-order Chebyshev filter. The noise figure (NF) increases at high frequency because of the source parasitic capacitors of the cascode transistor; so, noise cancelling technique is applied to the cascode transistor of the proposed LNA. Bias conditions and sizes of the transistors are optimized to cancel the nonlinear transconductance ([Formula: see text]). With this modified technique, low noise figure, high linearity and improved input and output matching can be attained for 3.1–10.6[Formula: see text]GHz frequency band. Post-layout simulation result of the proposed LNA shows the maximum power gain of 17[Formula: see text]dB at 5.5[Formula: see text]GHz frequency, NF of lower than 4.5[Formula: see text]dB over the whole band of 3.1–10.6[Formula: see text]GHz, maximum IIP2 of [Formula: see text]28[Formula: see text]dBm and IIP3 of [Formula: see text]7.5[Formula: see text]dBm, while dissipating 9[Formula: see text]mW (with buffer) from a 1.8 V supply voltage. It occupies [Formula: see text]m silicon die area.

scholarly journals Ultra compact multi-standard low-noise amplifiers in 28 nm CMOS with inductive peaking

2017 ◽  
Vol 10 (1) ◽  
pp. 47-57
Author(s):  
Elena Sobotta ◽  
Guido Belfiore ◽  
Frank Ellinger
Keyword(s):  
Noise Figure ◽  
Low Noise ◽  
Low Noise Amplifiers ◽  
Cmos Process ◽  
Bandwidth Enhancement ◽  
Dc Power ◽  
Active Inductors ◽  
Inductive Peaking ◽  
Noise Amplifier ◽  
28 Nm

This work presents the design of two compact multi-standard low-noise amplifier (LNA) in a 28 nm low-power bulk CMOS process. The transistor parameters were optimized by the gm/ID method taking into account the parasitics and the behavior of highly scaled transistors. To cover the industrial science medical (ISM)-bands around 2.4 and 5.8 GHz, the WLAN band as well as the Ku band a bandwidth enhancement is required. Two versions of LNAs, one with vertical inductors and one with active inductors, are implemented and verified by measurements. The noise figure (NF) exhibits 4.2 dB for the LNA with active inductors and 3.5 dB for the LNA with vertical inductors. The voltage gain reaches 12.8 and 13.4 dB, respectively, with a 3 dB-bandwidth of 20 GHz. Both input referred 1-dB-compression points are higher than −12 dBm making the chips attractive for communication standards with high linearity requirements. The chips consume 53 mW DC power and the LNA with active inductors occupies a core area of only 0.0018 mm2, whereas the version with vertical inductors requires 0.021 mm2.

scholarly journals Active Balun with Center-Tapped Inductor and Double-Balanced Gilbert Mixer for GNSS Applications

Electronics ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 1351
Author(s):  
Daniel Pietron ◽  
Tomasz Borejko ◽  
Witold Adam Pleskacz
Keyword(s):  
Phase Shift ◽  
Noise Figure ◽  
Low Noise ◽  
Global Navigation Satellite Systems ◽  
Cmos Process ◽  
Differential Signal ◽  
Satellite Systems ◽  
Active Balun ◽  
Noise Amplifier ◽  
Global Navigation Satellite

A new 1.575 GHz active balun with a classic double-balanced Gilbert mixer for global navigation satellite systems is proposed herein. A simple, low-noise amplifier architecture is used with a center-tapped inductor to generate a differential signal equal in amplitude and shifted in phase by 180°. The main advantage of the proposed circuit is that the phase shift between the outputs is always equal to 180°, with an accuracy of ±5°, and the gain difference between the balun outputs does not change by more than 1.5 dB. This phase shift and gain difference between the outputs are also preserved for all process corners, as well as temperature and voltage supply variations. In the balun design, a band calibration system based on a switchable capacitor bank is proposed. The balun and mixer were designed with a 110 nm CMOS process, consuming only a 2.24 mA current from a 1.5 V supply. The measured noise figure and conversion gain of the balun and mixer were, respectively, NF = 7.7 dB and GC = 25.8 dB in the band of interest.

Sign in / Sign up

Export Citation Format

Share Document