HEMODYNAMICS IN STENOSED ARTERIES — EFFECTS OF STENOSIS SHAPES

2010 ◽  
Vol 07 (03) ◽  
pp. 397-419 ◽  
Author(s):  
MOLOY K. BANERJEE ◽  
DEBABRATA NAG ◽  
RANJAN GANGULY ◽  
AMITAVA DATTA
Keyword(s):  
Pressure Loss ◽  
Reynolds Numbers ◽  
Loss Coefficient ◽  
Centerline Velocity ◽  
Hemodynamic Parameters ◽  
Gaussian Shape ◽  
Pressure Loss Coefficient ◽  
Flow Through ◽  
Recirculation Length ◽  
Hemodynamic Flow

A numerical analysis has been carried out to investigate the hemodynamic flow through stenosed arteries having mild (S = 25%) to severe (S = 65%) occlusions and under different regimes of flow Reynolds numbers ( Re ) ranging from 50 to 400. Influence of different stenosis shapes (rectangular, trapezoidal, cosine, and Gaussian) on key hemodynamic parameters e.g., recirculation length, wall shear stress (WSS), pressure drop, and irreversible pressure loss coefficient (C I ) are studied. It has been observed that for S = 25%, no flow separation takes place with cosine and Gaussian shaped stenoses for all the Re values considered, while for rectangular or trapezoidal shapes the flow begins to separate at Re = 400. At higher degrees of stenosis, post-stenotic recirculation is noticed for all the shapes considered — the largest recirculation length being observed with the rectangular shape. The peak centerline velocity in the stenosed region is more sensitive to a change in the degree of occlusion for rectangular stenosis than the other shapes. From the study, it is also revealed that the irreversible pressure loss coefficient (C I ) is the maximum for rectangular shaped stenosis, while it is the least for Gaussian shape. It is observed that at high Re regime, C I becomes insensitive to Re values and can be approximated to be a function of the degree of stenosis (S) and the stenosis shape only.

Pressure-Loss Coefficient of 90 deg Sharp-Angled Miter Elbows

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Wameedh T. M. Al-Tameemi ◽  
Pierre Ricco
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Pressure Loss ◽  
Dynamic Pressure ◽  
Reynolds Numbers ◽  
Loss Coefficient ◽  
Straight Pipe ◽  
Pressure Loss Coefficient ◽  
Circular Pipes ◽  
Piping Systems

The pressure drop across 90deg sharp-angled miter elbows connecting straight circular pipes is studied in a bespoke experimental facility by using water and air as working fluids flowing in the range of bulk Reynolds number 500<Re<60,000. To the best of our knowledge, the dependence on the Reynolds number of the pressure drop across the miter elbow scaled by the dynamic pressure, i.e., the pressure-loss coefficient K, is reported herein for the first time. The coefficient is shown to decrease sharply with the Reynolds number up to about Re=20,000 and, at higher Reynolds numbers, to approach mildly a constant K=0.9, which is about 20% lower than the currently reported value in the literature. We quantify this relation and the dependence between K and the straight-pipe friction factor at the same Reynolds number through two new empirical correlations, which will be useful for the design of piping systems fitted with these sharp elbows. The pressure drop is also expressed in terms of the scaled equivalent length, i.e., the length of a straight pipe that would produce the same pressure drop as the elbow at the same Reynolds number.

Vibration suppression investigation and parametric design of tri-axle straight heavy truck with pitch-resistant hydraulically interconnected suspension

2021 ◽  
pp. 107754632110396
Author(s):  
Fei Ding ◽  
Jie Liu ◽  
Chao Jiang ◽  
Haiping Du ◽  
Jiaxi Zhou ◽  
...  
Keyword(s):  
Surface Area ◽  
Dynamic Load ◽  
Pressure Loss ◽  
Vibration Suppression ◽  
Parametric Design ◽  
Suspension System ◽  
Loss Coefficient ◽  
The Body ◽  
Impedance Matrix ◽  
Pressure Loss Coefficient

The vibration suppression of the proposed pitch-resistant hydraulically interconnected suspension system for the tri-axle straight truck is investigated, and the vibration isolation performances are parametrically designed to achieve smaller body vibration and tire dynamic load using increased pitch stiffness and optimized pressure loss coefficient. For the hydraulic subsystem, the transfer impedance matrix method is applied to derive the impedance matrix. These hydraulic forces are incorporated into the motion equations of mechanical subsystem as external forces according to relationships between boundary flow and mechanical state vectors. In terms of the additional mode stiffness/damping and suspension performance requirements, the cylinder surface area, accumulator pressure, and damper valve’s pressure loss coefficient are comprehensively tuned with parametric design technique and modal analysis method. It is found the isolation capacity is heavily dependent on installation scheme and fluid physical parameters. Especially, the surface area can be designed for the oppositional installation to separately raise pitch stiffness without increasing bounce stiffness. The pressure loss coefficients are tuned with design of experiment approach and evaluated using all conflict indexes with normalized dimensionless evaluation factors. The obtained numerical results indicate that the proposed pitch-resistant hydraulically interconnected suspension system can significantly inhibit both the body and tire vibrations with decreased suspension deformation, and the tire dynamic load distribution among wheel stations is also improved.

The Characteristics Study of Helium-Xenon Mixture in Closed Brayton Cycle for Space Nuclear Reactor Power

2018 ◽  
Author(s):  
Xie Yang ◽  
Lei Shi
Keyword(s):  
Physical Properties ◽  
Pressure Loss ◽  
Nuclear Reactor ◽  
Reactor Power ◽  
Loss Coefficient ◽  
Working Fluid ◽  
System Efficiency ◽  
Pressure Loss Coefficient ◽  
Molar Weight ◽  
Xenon Mixture

Differing from the adoption of helium as working fluid of closed Brayton cycle (CBC) for terrestrial high temperature gas cooled reactor (HTGR) power plants, helium-xenon mixture with a proper molar weight was recommended as working fluid for space nuclear reactor power with CBC conversion. It is essential to figure out how the component of helium-xenon mixture affects the net system efficiency, in order to provide reference for the selection of appropriate cycle working fluid. After a discussion of the physical properties of different helium-xenon mixtures, the related physical properties are studied to analyze their affection on the key parameters of CBC, including adiabatic coefficient, recuperator effectiveness and normalized pressure loss coefficient. Then the comprehensive thermodynamics of CBC net system efficiency is studied in detail considering different helium-xenon mixtures. The physical properties study reveals that at 0.7 MPa and 400 K, the adiabatic coefficient of helium-xenon mixture increases with increased molar weight, from 0.400 (pure helium) to 0.414 (pure xenon), while recuperator effectiveness firstly increases and then decreases with the increase of molar weight, and the normalized pressure loss coefficient increases monotonically with molar weight increases. The thermodynamic analysis results show that the adiabatic coefficient has less effect on the net system efficiency, while the net system efficiency increases with increased recuperator effectiveness, and the net system efficiency decreases with normalized pressure loss coefficient increases. Finally, the mixture of helium-8.6% xenon was adopted as working fluid, instead of pure helium, for ensuring less turbine mechanicals (turbine and compressor) stages, and resulting maximum recuperator effectiveness. At the given cold / hot side temperature of 400 / 1300 K, the net system efficiency can reach 29.18% theoretically.

Rotating Annulus Component Performance Characterisation Based on CFD Analyses

2018 ◽  
Author(s):  
Youming Yuan ◽  
David Hunt
Keyword(s):  
Test Data ◽  
Pressure Loss ◽  
Model Performance ◽  
Internal Flow ◽  
Loss Coefficient ◽  
Performance Data ◽  
Pressure Loss Coefficient ◽  
1D Model ◽  
Torque Coefficient ◽  
Secondary Air

FloMASTER is a 1-D thermo-fluids system simulation tool and its component models depend on the characterisation data of the component performance. Such performance data is mainly based on data banks established from extensive tests exemplified by the books like “Internal Flow” by Miller [1] and “Handbook of Hydraulic Resistance” by Idelchik [2]. One of the key components of the gas turbine secondary air system is the rotating annulus. However, reliable data and correlations for performance characteristics like pressure loss coefficient, torque coefficient, windage and heat transfer for this component are rare and non-existent in the open literature for the case of both walls rotating simultaneously, which is becoming more common in today’s multi-spool military aero engines. To overcome this challenge of lack of reliable performance data and correlations, in this paper the Mentor Graphics 3D CFD tool “FloEFD” is used to model both inner wall rotating and outer wall rotating annulus flow, and to verify the 3D CFD results of performance data in terms of pressure loss coefficient and torque coefficient versus some published test data in the open literature. It is shown that the CFD gives results on pressure loss and torque coefficients that are in good agreement with test data based correlations used in FloMASTER. This demonstrates that 3D CFD can be used as a powerful tool for verifying the existing 1D model, extending the 1D model performance data range and generating new performance data for developing new components where such data is not available from open literature. A future project is to extend this approach to provide performance data for rotating annuli with both walls rotating. Such data will form the basis for developing a new component model for a rotating annulus with both walls rotating.

Optimization of an Axial Turbine Stage for Aerodynamic Inlet Blockage

2011 ◽  
Author(s):  
Mohammad Arabnia ◽  
Vadivel K. Sivashanmugam ◽  
Wahid Ghaly
Keyword(s):  
Pressure Loss ◽  
Suction Side ◽  
Loss Coefficient ◽  
Von Mises Stress ◽  
Optimization Approach ◽  
Design Point ◽  
Pressure Loss Coefficient ◽  
Design Variables ◽  
Blade Shape ◽  
Von Mises

This paper presents a practical and effective optimization approach to minimize 3D-related flow losses associated with high aerodynamic inlet blockage by re-stacking the turbine rotor blades. This approach is applied to redesign the rotor of a low speed subsonic single-stage turbine that was designed and tested in DLR, Germany. The optimization is performed at the design point and the objective is to minimize the rotor pressure loss coefficient as well as the maximum von Mises stress while keeping the same design point mass flow rate, and keeping or increasing the rotor blade first natural frequency. A Multi-Objective Genetic Algorithm (MOGA) is coupled with a Response Surface Approximation (RSA) of the Artificial Neural Network (ANN) type. A relatively small set of high fidelity 3D flow simulations and structure analysis are obtained using ANSYS Workbench Mechanical. That set is used to train and to test the ANN models. The stacking line is parametrically represented using a quadratic rational Bezier curve (QRBC). The QRBC parameters are directly related to the design variables, namely the rotor lean and sweep angles and the bowing parameters. Moreover, it results in eliminating infeasible shapes and in reducing the number of design variables to a minimum while providing a wide design space for the blade shape. The aero-structural optimization of the E/TU-3 turbine proved successful, the rotor pressure loss coefficient was reduced by 9.8% and the maximum von Mises stress was reduced by 36.7%. This improvement was accomplished with as low as four design variables, and is attributed to the reduction of 3D-related aerodynamic losses and the redistribution of stresses from the hub trailing edge region to the suction side maximum thickness area. The proposed parametrization is a promising one for 3D blade shape optimization involving several disciplines with a relatively small number of design variables.

The Influence of Different Rim Seal Geometries on Hot-Gas Ingestion and Total Pressure Loss in a Low-Pressure Turbine

2010 ◽  
Author(s):  
P. Schuler ◽  
W. Kurz ◽  
K. Dullenkopf ◽  
H.-J. Bauer
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Gas Flow ◽  
Low Pressure ◽  
Total Pressure Loss ◽  
Pressure Loss Coefficient ◽  
Low Pressure Turbine ◽  
Hot Gas ◽  
Flow Through ◽  
Total Pressure Loss Coefficient

In order to prevent hot-gas ingestion into the rotating turbo machine’s inside, rim seals are used in the cavities located between stator- and rotor-disc. The sealing flow ejected through the rim seal interacts with the boundary layer of the main gas flow, thus playing a significant role in the formation of secondary flows which are a major contributor to aerodynamic losses in turbine passages. Investigations performed in the EU project MAGPI concentrate on the interaction between the sealing flow and the main gas flow and in particular on the influence of different rim seal geometries regarding the loss-mechanism in a low-pressure turbine passage. Within the CFD work reported in this paper static simulations of one typical low-pressure turbine passage were conducted containing two different rim seal geometries, respectively. The sealing flow through the rim seal had an azimuthal velocity component and its rate has been varied between 0–1% of the main gas flow. The modular design of the computational domain provided the easy exchange of the rim seal geometry without remeshing the main gas flow. This allowed assessing the appearing effects only to the change of rim seal geometry. The results of this work agree with well-known secondary flow phenomena inside a turbine passage and reveal the impact of the different rim seal geometries on hot-gas ingestion and aerodynamic losses quantified by a total pressure loss coefficient along the turbine blade. While the simple axial gap geometry suffers considerable hot-gas ingestion upstream the blade leading edge, the compound geometry implying an axial overlapping presents a more promising prevention against hot-gas ingestion. Furthermore, the effect of rim seals on the turbine passage flow field has been identified applying adequate flow visualisation techniques. As a result of the favourable conduction of sealing flow through the compound geometry, the boundary layer is less lifted by the ejected sealing flow, thus resulting in a comparatively reduced total pressure loss coefficient over the turbine blade.

Effects of Bio-Inspired Micro-Scale Surface Patterns on the Profile Losses in a Linear Cascade

2019 ◽  
Vol 141 (12) ◽  
Author(s):  
Qiang Liu ◽  
Shan Zhong ◽  
Lin Li
Keyword(s):  
Pressure Loss ◽  
Reynolds Numbers ◽  
Loss Reduction ◽  
Turning Angle ◽  
Low Reynolds Numbers ◽  
Linear Cascade ◽  
Micro Scale ◽  
Pressure Loss Coefficient ◽  
Surface Patterns ◽  
Scale Surface

Abstract In this paper, we investigated the effects of herringbone riblets, a type of bio-inspired micro-scale surface patterns, on pressure losses and flow turning angles in a linear cascade over a range of low Reynolds numbers from 0.50 × 105 to 1.50 × 105 and at three different incidence angles. Our experiments showed that despite their micro-scale size, herringbone riblets produced a significant reduction in pressure loss and a substantial increase in flow turning angle except at the low end of the Reynolds numbers tested. In comparison to the baseline case without riblets, the highest reduction in the zone-averaged pressure loss coefficient behind one flow passage was 36.4% which was accompanied by a 4.1 deg increase in the averaged turning angle. The loss reduction was caused by a decrease in γmax at α = −1 deg, a narrower wake zone at α = 9 deg and a mixture of both at α = 4 deg due to the suppression of flow separation on the blade suction surface. It was also noted that such a significant improvement was always accompanied by the appearance of a serrated wake structure in the contours of pressure loss coefficient in which the region with a higher loss reduction occurring directly behind the divergent region of herringbone riblets. The observed improvement in cascade performance was attributed to the secondary flow motion produced by herringbone riblets which energizes the boundary layer. Overall, this work has produced convincing experimental evidence that herringbone riblets could be potentially used as passive flow control devices for reducing flow separation in compressors at low Reynolds numbers.

Sign in / Sign up

Export Citation Format

Share Document