Gas Flow Characteristics in a Plasma Process Chamber and Proposal of New Pulse-Controlled Gas Injection Method Using Interference Matrix Operation for Rapid Stabilization of Gas Pressure

2011 ◽  
Vol 51 (1) ◽  
pp. 016001
Author(s):  
Sadaharu Morishita ◽  
Tetsuya Goto ◽  
Yasuyuki Shirai ◽  
Tadahiro Ohmi
Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-10 ◽  
Author(s):  
Chaolin Zhang ◽  
Jiang Xu ◽  
Enyuan Wang ◽  
Shoujian Peng

Coal seam gas is a critical substance because it can be a source of a large quantity of clean energy as well as a dangerous source of risk. A pressure relief gas drainage is an effective and widely used method for coal seam gas recovery and gas disaster control in coal mines. A series of pressure relief gas drainage experiments were conducted using large-scale coal samples under different unloading stress paths in this study to explore the unloading stress paths. From the experimental results, the dynamic evolutions of gas pressure, coal temperature, and gas production were analyzed. The trends of gas pressure and coal temperature during pressure relief gas drainage were similar: dropping rapidly first and then slowly with time. Correspondingly, gas production was fast in the early stage of pressure relief gas drainage and became stable thereafter. Meanwhile, gas flow characteristics were significantly affected by the unloading stress paths. Gas pressure and coal temperature had the maximum descent by unloading stress in three directions simultaneously, and the unloading stress of the Z direction had the minimal impact when only unloading in one direction of stress. However, the influence of unloading stress paths on gas production was complex and time dependent. The difference coefficient parameter was proposed to characterize the influence degree of unloading stress paths on the pressure relief gas drainage effect. Eventually, the selection of unloading stress path under different situations was discussed based on time, which is expected to provide the basis for pressure relief gas drainage.


2021 ◽  
Vol 88 ◽  
pp. 103826
Author(s):  
Yiyu Lu ◽  
Jiankun Zhou ◽  
Honglian Li ◽  
Jiren Tang ◽  
Lei Zhou ◽  
...  

2009 ◽  
Vol 618-619 ◽  
pp. 627-630
Author(s):  
Stephen J. Bonner ◽  
Graham B. Schaffer ◽  
Ji Yong Yao

An aluminium alloy was sintered using a conventional press and sinter process, at various gas pressures, to observe the effect of sintering gas pressure on the densification rate. Compacts of aluminium alloy 2712 (Al-3.8Cu-1Mg-0.7Si-0.1Sn) were prepared from elemental powders and sintered in a horizontal tube furnace under nitrogen or argon at 590°C for up to 60 minutes, and air cooled. The gas flow was adjusted to achieve specific gas pressures in the furnace. It has been found that increasing the nitrogen pressure at the start of the isothermal holding stage to 160kPa increased the densification rate compared to standard atmospheric pressure sintering. Increasing the nitrogen pressure further, up to 600kPa, had no additional benefit. The densification rate was increased significantly by increasing the gas pressure to 600kPa during both heating and isothermal holding. Under argon the elevated pressure did not increase the densification rate. Results seem to suggest that the beneficial effect of the elevated pressure on the rate of densification is related to nitride formation.


1999 ◽  
Vol 121 (2) ◽  
pp. 96-101 ◽  
Author(s):  
H. Baca ◽  
J. Smith ◽  
A. T. Bourgoyne ◽  
D. E. Nikitopoulos

Results from experiments conducted in downward liquid-gas flows in inclined, eccentric annular pipes, with water and air as the working fluids, are presented. The gas was injected in the middle of the test section length. The operating window, in terms of liquid and gas superficial velocities, within which countercurrent gas flow occurs at two low-dip angles, has been determined experimentally. The countercurrent flow observed was in the slug regime, while the co-current one was stratified. Countercurrent flow fraction and void fraction measurements were carried out at various liquid superficial velocities and gas injection rates and correlated to visual observations through a full-scale transparent test section. Our results indicate that countercurrent flow can be easily generated at small downward dip angles, within the practical range of liquid superficial velocity for drilling operations. Such flow is also favored by low gas injection rates.


2010 ◽  
Vol 146-147 ◽  
pp. 1049-1055
Author(s):  
Xue Liu Fan ◽  
Xiang Chen ◽  
Yan Xiang Li

The acoustic properties of aluminum foams by gas injection method were studied experimentally. The micro and macro structure of aluminum foam with closed cells were observed by optical microscope (OM) and scanning electron microscope (SEM). The special structure of the closed-pores of the aluminum foams have leaded to good performance of the sound absorption based on three mechanisms: Helmholtz resonance, cell wall vibration and viscous and thermal effects. The effect of cell sizes, thickness of aluminum foams has been investigated and the cavity set at the back of the foam samples on the sound absorption efficiency of the foams has been measured. Analytical models of membrane vibrations were used to explain the sound absorption capacity of the foams.


Sign in / Sign up

Export Citation Format

Share Document