Environment Influence on the Properties of Functional Parts Made of HIPS Material

2021 ◽  
Vol 105 (1) ◽  
pp. 431-440
Author(s):  
Pavel Šafl ◽  
Jana Zimáková ◽  
Tomáš Binar
Keyword(s):  
Electron Microscope ◽  
3D Printing ◽  
Tensile Test ◽  
Uv Light ◽  
Starting Material ◽  
Climatic Chamber ◽  
3D Printed ◽  
Formation Of Cracks ◽  
Printed Materials ◽  
Degree Of Degradation

The aim of this work is to study the climatic influences on 3D printed materials. This study focuses on the HIPS material, which was chosen as the starting material for further studies. The material in the field of 3D printing is known for its rapid photooxidation, which results in the formation of cracks in the final product. A climatic chamber was used for degradation, in which UV light, heat and increased humidity were applied to the material. The degree of degradation was then checked by tensile test and electron microscope.

APPLICATION OF 3D PRINTING TECHNOLOGY FOR RAPID TOOLING IN SHEET METAL FORMING

2020 ◽  
Vol 3 ◽  
pp. 20-30
Author(s):  
M.A. SEREZHKIN ◽  
D.O. KLIMYUK ◽  
A.I. PLOKHIKH
Keyword(s):  
3D Printing ◽  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Rapid Tooling ◽  
Printing Technology ◽  
3D Printing Technology ◽  
3D Printed ◽  
Printed Materials ◽  
Printing Parameters

The article presents the study of the application of 3D printing technology for rapid tooling in sheet metal forming for custom or small–lot manufacturing. The main issue of the usage of 3D printing technology for die tooling was discovered. It is proposed to use the method of mathematical modelling to investigate how the printing parameters affect the compressive strength of FDM 3D–printed parts. Using expert research methods, the printing parameters most strongly affecting the strength of products were identified for further experiments. A method for testing the strength of 3D–printed materials has been developed and tested.

scholarly journals Cost-Effectively 3D-Printed Rigid and Versatile Interpenetrating Polymer Networks

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4544
Author(s):  
Osman Konuray ◽  
Arnau Sola ◽  
Jordi Bonada ◽  
Agnieszka Tercjak ◽  
Albert Fabregat-Sanjuan ◽  
...  
Keyword(s):  
3D Printing ◽  
Polymer Networks ◽  
Complex Form ◽  
Interpenetrating Polymer Networks ◽  
Dual Processing ◽  
Digital Light Processing ◽  
Superior Mechanical Properties ◽  
3D Printed ◽  
Acrylate Resin ◽  
Printed Materials

Versatile acrylate–epoxy hybrid formulations are becoming widespread in photo/thermal dual-processing scenarios, especially in 3D printing applications. Usually, parts are printed in a stereolithography or digital light processing (DLP) 3D printer, after which a thermal treatment would bestow the final material with superior mechanical properties. We report the successful formulation of such a hybrid system, consisting of a commercial 3D printing acrylate resin modified by an epoxy–anhydride mixture. In the final polymeric network, we observed segregation of an epoxy-rich phase as nano-domains, similar to what was observed in a previous work. However, in the current work, we show the effectiveness of a coupling agent added to the formulation to mitigate this segregation for when such phase separation is undesired. The hybrid materials showed significant improvement of Young’s modulus over the neat acrylate. Once the flexible, partially-cured material was printed with a minimal number of layers, it could be molded into a complex form and thermally cured. Temporary shapes were readily programmable on this final material, with easy shape recovery under mild temperatures. Inspired by repairable 3D printed materials described recently, we manufactured a large object by printing its two halves, and then joined them covalently at the thermal cure stage with an apparently seamless union.

Thermal Conductivity Testing Apparatus for 3D Printed Materials

2017 ◽  
Author(s):  
Tiffaney Flaata ◽  
Gregory J. Michna ◽  
Todd Letcher
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Polymer Composite ◽  
Heat Exchangers ◽  
Fused Deposition ◽  
3D Printed ◽  
Printed Materials ◽  
Metal Polymer

Additive manufacturing, the layer-by-layer creation of parts, was initially used for rapid prototyping of new designs. Recently, due to the decrease in the cost and increase in the resolution and strength of additively manufactured parts, additive manufacturing is increasingly being used for production of parts for end-use applications. Fused Deposition Modeling (FDM), a type of 3d printing, is a process of additive manufacturing in which a molten thermoplastic material is extruded to create the desired geometry. Many potential heat transfer applications of 3d printed parts, including the development of additively manufactured heat exchangers, exist. In addition, the availability of metal/polymer composite filaments, first used for applications such as tooling for injection molding applications and to improve wear resistance, could lead to increased performance 3d printed heat exchangers because of the higher thermal conductivity of the material. However, the exploitation of 3d printing for heat transfer applications is hindered by a lack of reliable thermal conductivity data for as-printed materials, which typically include significant void fractions. In this experimental study, an apparatus to measure the effective thermal conductivity of 3d printed composite materials was designed and fabricated. Its ability to accurately measure the thermal conductivity of polymers was validated using a sample of acrylic, whose conductivity is well understood. Finally, the thermal conductivities of various 3d printed polymer, metal/polymer composite, and carbon/polymer composite filaments were measured and are reported in this paper. The materials used are acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), stainless steel/PLA, Brass/PLA, and Bronze/PLA.

Utility and cost–effectiveness of 3D-printed materials for clinical use

2019 ◽  
Vol 3 (4) ◽  
pp. 209-218 ◽  
Author(s):  
Julian Vitali ◽  
Matthew Cheng ◽  
Michael Wagels
Keyword(s):  
Cost Effectiveness ◽  
3D Printing ◽  
Relevant Literature ◽  
Clinical Use ◽  
Surgical Guides ◽  
Rigorous Testing ◽  
Clinical Benefits ◽  
3D Printed ◽  
Surgical Adjunct ◽  
Printed Materials

This review summarizes the utility of 3D-printing as a surgical adjunct, reviewing the cost–effectiveness. The relevant literature was analyzed outlining the utility and/or cost–effectiveness of 3D-printing for clinical use. Compared with existing methods, the evidence suggests an advantage of using 3D-printing as a technology in the treatment of complex clinical cases. However, in high frequency cases, the additional preoperative expenses are not justified. Considerable evidence of its clinical benefits exists for the application of 3D-printed anatomical models and teaching tools. However, the evidence supporting 3D-printing’s use as surgical guides or implantable devices is less clear. Furthermore, caution must exist when using these devices in the clinical setting due to a paucity of rigorous testing, global regulation and long-term data.

scholarly journals Investigation and Attempt to 3D Print Piezoelectric 0-3 Composites Made of Photopolymer Resins and PZT

2020 ◽  
Author(s):  
Rytis Mitkus ◽  
Andreas Pierou ◽  
Julia Feder ◽  
Michael Sinapius
Keyword(s):  
3D Printing ◽  
Lead Zirconate Titanate ◽  
Uv Light ◽  
Tape Casting ◽  
Particle Dispersion ◽  
Particle Sedimentation ◽  
Piezoelectric Composites ◽  
3D Print ◽  
Starting Point ◽  
3D Printed

Abstract The present study demonstrates the manufacturing and characterization of 0-3 piezoelectric composites made of up to 10 vol% of Lead Zirconate Titanate (PZT) particles and photopolymer resins. The tape-casting method was used to investigate the curing behavior, PZT loading limitations and the overall feasibility of the suspensions for 3D printing. Piezoelectric composites were 3D printed with a commercial DLP type 3D printer. As a starting point, the maximum possible vol% loading of PZT ceramic for each photopolymer resin was investigated. Five different commercially available photopolymer resins from Formlabs (Somerville, MA, US) were used. It was found that the addition of PZT particles to the photopolymer increases the time required for the photopolymer to solidify because PZT particles scatter the UV light. The approximate solidification time of each composition was measured, followed by viscosity measurements. SEM imaging of the composites showed good particle dispersion with minimum agglomeration, low particle sedimentation, but the weak bond between PZT particles and the photopolymers. Best performed material composition with 10 vol% of PZT was used for 3D printing. An attempt to shorten exposure time during printing was done by adding photoinitiator TPO. Suspensions with and without TPO were 3D printed and compared.

scholarly journals Stabilization of Electrospun Nanofiber Mats Used for Filters by 3D Printing

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1618 ◽  
Author(s):  
Kozior ◽  
Trabelsi ◽  
Mamun ◽  
Sabantina ◽  
Ehrmann
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Water Pressure ◽  
Volume Ratio ◽  
Fused Deposition ◽  
Rigid Objects ◽  
Deposition Modeling ◽  
3D Printed ◽  
Printed Materials ◽  
Nanofiber Mats

Electrospinning is a well-known technology used to create nanofiber mats from diverse polymers and other materials. Due to their large surface-to-volume ratio, such nanofiber mats are often applied as air or water filters. Especially the latter, however, have to be mechanically highly stable, which is challenging for common nanofiber mats. One of the approaches to overcome this problem is gluing them on top of more rigid objects, integrating them in composites, or reinforcing them using other technologies to avoid damage due to the water pressure. Here, we suggest another solution. While direct 3D printing with the fused deposition modeling (FDM) technique on macroscopic textile fabrics has been under examination by several research groups for years, here we report on direct FDM printing on nanofiber mats for the first time. We show that by choosing the proper height of the printing nozzle above the nanofiber mat, printing is possible for raw polyacrylonitrile (PAN) nanofiber mats, as well as for stabilized and even more brittle carbonized material. Under these conditions, the adhesion between both parts of the composite is high enough to prevent the nanofiber mat from being peeled off the 3D printed polymer. Abrasion tests emphasize the significantly increased mechanical properties, while contact angle examinations reveal a hydrophilicity between the original values of the electrospun and the 3D printed materials.

3D-printed polypropylene transtibial sockets: Mechanical behavior

2020 ◽  
pp. 095440622094392
Author(s):  
MacArthur L Stewart
Keyword(s):  
3D Printing ◽  
Yield Strength ◽  
Tensile Test ◽  
Tensile Properties ◽  
Material Properties ◽  
Standard Test ◽  
Test Method ◽  
Material Behavior ◽  
Cross Sectional ◽  
3D Printed

This paper defines the tensile properties of a successfully worn 3D-printed transtibial socket. The socket was printed from a proprietary polypropylene filament and FDM 3D-printing process. Fused disposition modeling involves producing successive cross-sectional layers on top of one another and welding them together. Because of this, a notch is formed between the printed layers. As part of this investigation, tensile test specimens were die-cut perpendicular to the material direction and tested according to ASTM D638—Standard Test Method for Tensile Properties of Plastics. From the measured load–elongation data, stress–strain curves and the corresponding material properties were determined, including modulus of elasticity E, Poisson’s ratio ν, yield strength Sy, and ultimate strength Su. The average values for each of these material properties were 955 MPa, 0.35, 11.4 MPa, and 16.3 MPa, respectively. In addition to defining tensile properties, this work demonstrated a viable methodology for characterizing the as-built material behavior of 3D-printed sockets.

scholarly journals Surface Modification of 3D Printed PLA Objects by Fused Deposition Modeling: A Review

2019 ◽  
Vol 3 (2) ◽  
pp. 43 ◽  
Author(s):  
Eda Baran ◽  
H. Erbil
Keyword(s):  
Surface Modification ◽  
3D Printing ◽  
Plasma Treatment ◽  
Fused Deposition Modeling ◽  
Uv Light ◽  
Surface Modifications ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed ◽  
Appearance Properties

Polylactic acid (PLA) filaments are very popular as a thermoplastic source used in the 3D printing field by the “Fused Deposition Modeling” method in the last decade. The PLA market is expected to reach 5.2 billion US dollars in 2020 for all of its industrial uses. On the other hand, 3D printing is an expanding technology that has a large economic potential in many industries where PLA is one of the main choices as the source polymer due to its ease of printing, environmentally friendly nature, glossiness and multicolor appearance properties. In this review, we first reported the chemical structure, production methods, general properties, and present market of the PLA. Then, the chemical modification possibilities of PLA and its use in 3D printers, present drawbacks, and the surface modification methods of PLA polymers in many different fields were discussed. Specifically, the 3D printing method where the PLA filaments are used in the extrusion-based 3D printing technologies is reviewed in this article. Many methods have been proposed for the permanent surface modifications of the PLA where covalent attachments were formed such as alkaline surface hydrolysis, atom transfer polymerization, photografting by UV light, plasma treatment, and chemical reactions after plasma treatment. Some of these methods can be applied for surface modifications of PLA objects obtained by 3D printing for better performance in biomedical uses and other fields. Some recent publications reporting the surface modification of 3D printed PLA objects were also discussed.

Cross-linkable multi-stimuli responsive hydrogel inks for direct-write 3D printing

2017 ◽  
Vol 8 (29) ◽  
pp. 4199-4206 ◽  
Author(s):  
Dylan G. Karis ◽  
Robert J. Ono ◽  
Musan Zhang ◽  
Ankit Vora ◽  
Duane Storti ◽  
...  
Keyword(s):  
3D Printing ◽  
Uv Light ◽  
Direct Write ◽  
Stimuli Responsive ◽  
3D Printed

Triple-stimuli responsive hydrogel can be 3D printed and cross-linked in the presence of a photoradical generator and 365 nm UV light.

scholarly journals Optimization of Abs 3D-Printing Method and Parameters

1970 ◽  
Vol 3 (1) ◽  
pp. 44-51
Author(s):  
Paweł Żur ◽  
Alicja Kołodziej ◽  
Andrzej Baier ◽  
Grzegorz Kokot
Keyword(s):  
3D Printing ◽  
Tensile Test ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Electric Car ◽  
University Of Technology ◽  
Static Tensile ◽  
3D Printed ◽  
Printing Method

The paper presents research on the method of 3D-printing ABS (Acrylonitrile butadiene styrene). Series of specimens were 3D-printed in FDM (Fused Deposition Modelling) technology with variable parameters. The influence of the following parameters has been checked: temperature of printing and infill density. Moreover, the material properties of raw, unprocessed ABS have been inspected. The tensile strength of specimens and Young’s modulus have been determined in a static tensile test. Tests were carried out in compliance with the ASTM D638-14 standard. Obtained results were then compared with the material datasheet. Optimum printing method has been defined. The carried out research resulted in optimizing the printing method for ABS vehicle parts applied in Silesian Greenpower electric car. The car has been developed by students of The Silesian University of Technology in Gliwice, Poland as an interfaculty students’ project. Results of the tensile test research have been analysed and discussed and conclusions have been presented in the following article.

Sign in / Sign up

Export Citation Format

Share Document