scholarly journals Strength and Drying Shrinkage of Alkali-Activated Slag Paste and Mortar

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Mao-chieh Chi ◽  
Jiang-jhy Chang ◽  
Ran Huang
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Portland Cement ◽  
Liquid Slag ◽  
Drying Shrinkage ◽  
Curing Temperature ◽  
Alkali Activated Slag ◽  
Cement Mortars ◽  
Activated Slag ◽  
Alkali Activated

The aim of this study is to investigate the strengths and drying shrinkage of alkali-activated slag paste and mortar. Compressive strength, tensile strength, and drying shrinkage of alkali-activated slag paste and mortar were measured with various liquid/slag ratios, sand/slag ratios, curing ages, and curing temperatures. Experimental results show that the higher compressive strength and tensile strength have been observed in the higher curing temperature. At the age of 56 days, AAS mortars show higher compressive strength than Portland cement mortars and AAS mortars with liquid/slag ratio of 0.54 have the highest tensile strength in all AAS mortars. In addition, AAS pastes of the drying shrinkage are higher than AAS mortars. Meanwhile, higher drying shrinkage was observed in AAS mortars than that observed comparable Portland cement mortars.

A Review of Alkali-Activated Slag as Cement Replacement

2019 ◽  
Vol 803 ◽  
pp. 262-266
Author(s):  
Osama Ahmed Mohamed ◽  
Maadoum M. Mustafa
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Construction Industry ◽  
Ordinary Portland Cement ◽  
Environmental Footprint ◽  
Alkali Activated Slag ◽  
Cement Replacement ◽  
Activated Slag ◽  
Alkali Activated

Alkali activated slag (AAS) offers opportunities to the construction industry as an alternative to ordinary Portland cement (OPC). The production of OPC and its use contributes significantly to release of CO2 into the atmosphere while AAS is an industrial by-product that contributes much less to the environmental footprint that needs to be recycled if not landfilled. This paper outlines some of the key properties, merits and demerits of AAS when used as alternative to OPC. Competitive compressive strength of AAS concrete is amongst of the advantages of replacing cement with AAS while high shrinkage and carbonation levels are potential disadvantages.

Properties of Alkli-Activated Slag Cement Compounded with Soluble Glasses with a High Silicate Modulus

2013 ◽  
Vol 712-715 ◽  
pp. 905-908
Author(s):  
Qun Pan ◽  
Bin Zhu ◽  
Xiao Huang ◽  
Lin Liu
Keyword(s):  
Compressive Strength ◽  
Cement Mortar ◽  
Strength Characteristics ◽  
Slag Cement ◽  
Alkali Activated Slag ◽  
Cement Mortars ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated ◽  
High Silicate

Properties of alkali-activated slag cements compounded with soluble glasse with a high silicate modulus Ms=2.6 were detailedly studied in this paper, including compressive strength and flexure strength characterictics at the ages of 3,7,28 days and flow values of fresh cement mixtures on a jolting table. As a result, with the compressive strength at the age of 28 days of 95.6-107.8 MPa has been developed, and the flow values and strength characteristics of alkali-activated slag cement mortars increased with increase in a water to cement (alkaline activator solution to slag) ratio, and the flow value (determined on the cement mortar mixtures) would reach 145 mm. Moreover, the development speed of strength characteristics of mortar specimens would be affected negatively by increasing of water demand (requirement).

scholarly journals Effect of Rheology of Fresh Paste on the Pore Structure and Properties of Pervious Concrete Based on the High Fluidity Alkali-Activated Slag

Crystals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 593
Author(s):  
Haining Geng ◽  
Qing Xu ◽  
Saiful B. Duraman ◽  
Qiu Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Pore Structure ◽  
Water Permeability ◽  
Coarse Aggregate ◽  
Pervious Concrete ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Alkali Activated

Pervious concrete is made of cementitious materials, coarse aggregate, water and additives, with characteristic macro- and meso-connected pore structure, which enables the acceptable mechanical properties and high water permeability for pavement and road applications. In this study, the effect of rheology of fresh alkali-activated slag paste on the sedimentation of paste on the bottom of pervious concrete, meso-structure, connected porosity, mechanical properties and water permeability was investigated by a range of analytical techniques through varying the equivalent alkali content to control the rheology of fresh paste in the pervious concrete. The compressive strength of pervious concrete was related to the percentage area of paste and the average thickness of paste on the surface of coarse aggregate. The tensile strength and water permeability were correlated to the connected porosity of pervious concrete and the rheology of fresh paste. A relative lower fluidity, higher viscosity and shear stress of fresh alkali-activated slag paste favoured lower sedimentation of paste on the bottom of pervious concrete, higher connected porosity, tensile strength and water permeability. There was no correlation between compressive strength and tensile strength of pervious concrete.

scholarly journals Effects of Aging on the Tensile Properties of Polyethylene Fiber-Reinforced Alkali-Activated Slag-Based Composite

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Jeong-Il Choi ◽  
Se-Eon Park ◽  
Su-Tae Kang ◽  
Bang Yeon Lee
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Tensile Properties ◽  
Fiber Reinforced ◽  
Alkali Activated Slag ◽  
Polyethylene Fiber ◽  
Activated Slag ◽  
Effects Of Aging ◽  
Effect Of Age ◽  
Alkali Activated

Information on the effect of age on the tensile behavior of fiber-reinforced alkali-activated slag-based composite is fairly limited. Therefore, the purpose of this study is to experimentally investigate the effect of age on the compressive strength and tensile properties of the fiber-reinforced alkali-activated slag-based composite. A binder including slag and alkali activators, chemical admixtures, and a reinforcing fiber were selected, and the mixture proportion was determined to make a fiber-reinforced alkali-activated slag-based composite with high ductility. Compressive strength and tensile strength tests were performed, and values were measured at 3, 5, 7, 14, 28, and 90 days. Test results showed that the compressive strength increased as the age increased. Although the first-cracking strength increased like the compressive strength, the increases of tensile strength and tensile strain capacity were not significant compared with those of compressive strength and first-cracking strength.

scholarly journals Use of Industrial Waste Slag in Alkali-Activated Slag Ceramsite Concrete Hollow Blocks

2018 ◽  
Vol 8 (12) ◽  
pp. 2358 ◽  
Author(s):  
Zhenzhen Jiao ◽  
Ying Wang ◽  
Wenzhong Zheng ◽  
Wenxuan Huang ◽  
Xianyu Zhou
Keyword(s):  
Compressive Strength ◽  
Industrial Waste ◽  
Drying Shrinkage ◽  
Concrete Block ◽  
Na2o Content ◽  
Alkali Activated Slag ◽  
Viable Solution ◽  
Optimal Mix ◽  
Activated Slag ◽  
Alkali Activated

In this paper, a parametric experimental study developing the alkali-activated slag concrete hollow block (AASCHB) is discussed. Fourteen trial mixes of alkali-activated slag concrete containing pottery sand and ceramsite with different water-to-slag ratios, sand ratios, silicate moduli, and Na2O contents were evaluated to determine the optimal mix for high compressive strength and low drying shrinkage. All four factors evaluated were found to be significant for the desired properties. A series of 390 × 190 × 190 mm3 AASCHBs were prepared using the optimal mix with a water-to-slag ratio of 0.35, sand ratio of 0.64, silicate modulus of 1.2, and Na2O content of 8%. The compressive strength, flexural strength, water absorption, and moisture content tests of these blocks indicate that the resulting AASCHB can be classified under the strength grade of MU15 as a load-bearing hollow concrete block. The proposed AASCHBs appear to provide a viable solution to the environmental problems of industrial waste and cement production emissions, leading to more sustainable buildings without compromising structural performance.

scholarly journals Understanding the Role of Metakaolin towards Mitigating the Shrinkage Behavior of Alkali-Activated Slag

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6962
Author(s):  
Bo Fu ◽  
Zhenyun Cheng ◽  
Jingyun Han ◽  
Ning Li
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Activator Concentration ◽  
Reaction Products ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Alkali Activated ◽  
Shrinkage Behavior

This research investigates the mechanism of metakaolin for mitigating the autogenous and drying shrinkages of alkali-activated slag with regard to the activator parameters, including concentration and modulus. The results indicate that the incorporation of metakaolin can decrease the initial viscosity and setting time. Increasing activator concentration can promote the reaction process and shorten the setting time. An increase in the metakaolin content induces a decrease in compressive strength due to reduced formation of reaction products. However, increasing activator dosage and modulus can improve the compressive strength of alkali-activated slag containing 30% metakaolin. The inclusion of metakaolin can mitigate the autogenous and drying shrinkage of alkali-activated slag by coarsening the pore structure. On the other hand, increases in activator concentration and modulus result in an increase in magnitude of the autogenous and drying shrinkage of alkali-activated slag containing metakaolin. The influence of the activator modulus on the shrinkage behavior of alkali-activated slag-metakaolin binary system should be further investigated.

scholarly journals Strain-Hardening and High-Ductile Behavior of Alkali-Activated Slag-Based Composites with Added Zirconia Silica Fume

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3523 ◽  
Author(s):  
Jeong-Il Choi ◽  
Se-Eon Park ◽  
Huy Hoàng Nguyễn ◽  
Sang Lyul Cha ◽  
Bang Yeon Lee
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Silica Fume ◽  
Tensile Strain ◽  
Alkali Activated Slag ◽  
Strain Capacity ◽  
Activated Slag ◽  
Ductile Behavior ◽  
Tensile Strain Capacity ◽  
Alkali Activated

This paper presents an experimental study on the effects of zirconia silica fume on the composite properties and cracking patterns of fiber-reinforced alkali-activated slag-based composites. Four mixtures were prepared with added zirconia silica fume and varying water-to-binder ratio. Polyethylene fiber was used as a reinforcing fiber for all the mixtures at a volumetric ratio of 2.0% cubic specimens and uniaxial tensile specimens were prepared to evaluate their density, compressive strength, and tensile behavior. The test results demonstrated that the compressive strength, tensile strength, and tensile strain capacity of the composite can be simultaneously improved by incorporating zirconia silica fume. A mixture incorporating zirconia silica fume showed high-ductile behavior of 26.5% higher tensile strength, and 13.7% higher tensile strain capacity than the mixture without zirconia silica fume. The composite with added zirconia silica fume also showed excellent cracking patterns, i.e., narrow crack spacing and crack width.

scholarly journals Effect of Dosage of Alkaline Activator on the Properties of Alkali-Activated Slag Pastes

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Zhenzhen Jiao ◽  
Ying Wang ◽  
Wenzhong Zheng ◽  
Wenxuan Huang
Keyword(s):  
Compressive Strength ◽  
Room Temperature ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Engineering Properties ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Good Workability ◽  
Alkali Activated

This study focused on the engineering properties of alkali-activated slag (AAS) pastes prepared by mixing an activator consisting of sodium silicate and sodium hydroxide at room temperature. The water-to-slag ratio of AAS paste was kept constant at 0.35 by mass. AAS pastes were prepared using the activator with five different silicate moduli of 1, 1.2, 1.4, 1.6, and 1.8 and three different Na2O contents of 6%, 8%, and 10%. The results showed that both the silicate moduli and Na2O contents had significant effects on the engineering properties of AAS pastes. All the AAS pastes exhibited properties such as fast setting, good workability, and high early compressive strength. The final setting time varied from 9 to 36 min, and the fluidity was in the range of 147–226 mm. The 1 d compressive strength of all the AAS pastes, which could be easily achieved, had values above 55 MPa, whereas the highest strength obtained was 102 MPa with the silicate modulus of 1 and Na2O content of 8% at room temperature. The drying shrinkage increased as the silicate modulus increased. Furthermore, the hydration products and microstructures of AAS pastes were explained according to the microanalysis methods.

Shrinkage-Reducing Admixture Efficiency in Alkali-Activated Slag across the Different Doses of Activator

2018 ◽  
Vol 761 ◽  
pp. 19-22 ◽  
Author(s):  
Vlastimil Bílek Jr. ◽  
Lukáš Kalina ◽  
Ondřej Fojtík
Keyword(s):  
Compressive Strength ◽  
Drying Shrinkage ◽  
Strength Development ◽  
Alkali Activated Slag ◽  
Reducing Ability ◽  
Wide Range ◽  
Shrinkage Reducing Admixture ◽  
Negative Effect ◽  
Activated Slag ◽  
Alkali Activated

One of the largest obstacles for the wider use of alkali-activated slag (AAS) in a building industry is its severe drying shrinkage. According to some studies shrinkage-reducing admixtures (SRAs) could be a solution of this problem, but they were also reported to have a fatal impact on AAS hydration resulting in a serious strength development slowdown. The aim of this paper was to investigate this phenomenon in a wide range of the waterglass doses (4–12% Na2O of the slag mass). Mortars without and with 2% of SRA based on hexylene glycol were prepared and their shrinkage and compressive strength development was tested. By far the highest shrinkage reduction was observed for the lowest doses of waterglass, but these were also the cases of the highest compressive strength decrease. However, it is possible to suppress the negative effect of SRA on AAS strength development through the activator dose increase with certainly decreased shrinkage reducing ability of SRA.

Sign in / Sign up

Export Citation Format

Share Document