scholarly journals A Compact Size 4–19.1 GHz Heart Shape UWB Antenna with Triangular Patches

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Gokmen Isik ◽  
Serkan Topaloglu
Keyword(s):  
Radiation Pattern ◽  
Input Impedance ◽  
Patch Antennas ◽  
Frequency Range ◽  
Uwb Antenna ◽  
Radiation Characteristics ◽  
Narrow Bandwidth ◽  
Compact Size ◽  
Uwb Applications

An ultrawideband antenna is designed, simulated, and realized. To overcome the narrow bandwidth characteristics of basic patch antennas, the structure of the radiation pattern is optimized by the aid of elliptical and rectangular patches. Also triangular patches are applied to the antenna edge in order to enhance the VSWR and gain properties. A typical VSWR of 1.5 (less than 2 in the whole frequency range) and a typical gain of 2 dBi (mainly above 1 dBi in the whole frequency range) are observed. The simulations present that the designed antenna has a bandwidth ratio of ~5 : 1 within the frequency range of 4–19.1 GHz with compact dimensions of 25 × 26 mm2. It is fabricated on a 0.5 mm thick, RO3035 substrate. The input impedance, gain, and radiation characteristics of the antenna are also presented. With these properties, it is verified that, with its novel shape, the proposed antenna can be used for various UWB applications.

Closed Loop Resonator Based Compact UWB Antenna with Single Notched Band Varying between WLAN and X-band for UWB Applications

Frequenz ◽  
2020 ◽  
Vol 74 (5-6) ◽  
pp. 201-209
Author(s):  
Mohammad Ahmad Salamin ◽  
Sudipta Das ◽  
Asmaa Zugari
Keyword(s):  
Closed Loop ◽  
Ground Plane ◽  
Frequency Range ◽  
Uwb Antenna ◽  
Notched Band ◽  
X Band ◽  
Compact Size ◽  
Simulation Results ◽  
Uwb Applications ◽  
Good Agreement

AbstractIn this paper, a novel compact UWB antenna with variable notched band characteristics for UWB applications is presented. The designed antenna primarily consists of an adjusted elliptical shaped metallic patch and a partial ground plane. The proposed antenna has a compact size of only 17 × 17 mm2. The suggested antenna covers the frequency range from 3.1 GHz to 12 GHz. A single notched band has been achieved at 7.4 GHz with the aid of integrating a novel closed loop resonator at the back plane of the antenna. This notched band can be utilized to alleviate the interference impact with the downlink X-band applications. Besides, a square slot was cut in the loop in order to obtain a variable notched band. With the absence and the existence of this slot, the notched band can be varied to mitigate interference of the upper WLAN band (5.72–5.82 GHz) and X-band (7.25–7.75 GHz) with UWB applications. A good agreement between measurement and simulation results was achieved, which affirms the appropriateness of this antenna for UWB applications.

scholarly journals A Compact CPW-Fed UWB Antenna with Dual Band-Notched Characteristics

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Aiting Wu ◽  
Boran Guan
Keyword(s):  
Simple Structure ◽  
Ground Plane ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Frequency Range ◽  
Uwb Antenna ◽  
Compact Size ◽  
Excellent Candidate ◽  
Uwb Applications ◽  
Good Agreement

A compact CPW-fed planar UWB antenna with dual band-notched property is presented. The dual band rejection is achieved by etching a C-shaped slot on the radiation patch and two L-shaped parasitic strips in the ground plane. The experimental and measured results show that the proposed antenna exhibits an impedance bandwidth over an ultrawideband frequency range from 2.4 to 12.5 GHz with VSWR less than 2, except for two stopbands at 3.3 to 3.75 GHz and 5.07 to 5.83 GHz for filtering the WiMAX and WLAN signals, respectively. It also demonstrates a nearly omnidirectional radiation pattern. The fabricated antenna has a tiny size, only 32 mm × 32 mm × 0.508 mm. The simulated results are compared with the measured performance and show good agreement. The simple structure, compact size, and good characteristics make the proposed antenna an excellent candidate for UWB applications.

scholarly journals A Circular Disc Microstrip Antenna with Dual Notch Band for GSM/Bluetooth and Extended UWB Applications

2018 ◽  
Vol 7 (2.16) ◽  
pp. 11
Author(s):  
Sanjeev Kumar ◽  
Ravi Kumar ◽  
Rajesh Kumar Vishwakarma
Keyword(s):  
Radiation Pattern ◽  
Microstrip Antenna ◽  
Ground Plane ◽  
Circular Disc ◽  
Ultra Wideband ◽  
Resonant Circuit ◽  
Frequency Range ◽  
Notch Band ◽  
Uwb Applications ◽  
Ku Band

A microstrip antenna with a circular disc design and modified ground is proposed in this paper. Circular shapes of different size have been slotted out from the radiating patch for achieving extended ultra wideband (UWB) with GSM/Bluetooth bands with maximum bandwidth of 17.7 GHz (0.88-18.6 GHz). Further, characteristic of dual notch band is achieved, when a combination of T and L-shaped slots are etched into the circular disc and ground plane respectively. Change in length of slots is controlling the notch band characteristics. The proposed antenna has rejection bandwidth of 1.3-2.2 GHz (LTE band), 3.2-3.9 GHz (WiMAX band) and 5.2-6.1 GHz (WLAN band) respectively. It covers the frequency range of 0.88-18.5 GHz with the VSWR of less than 2. Also, an equivalent parallel resonant circuit has been demonstrated for band notched frequencies of the designed antenna. The gain achieved by the proposed antenna is 6.27 dBi. This antenna has been designed, investigated and fabricated for GSM, Bluetooth, UWB, X and Ku band applications. The stable gain including H & E-plane radiation pattern with good directivity and omnidirectional behavior is achieved by the proposed antenna. Measured bandwidths are 0.5 GHz, 0.8 GHz, 1.1 GHz and 11.7 GHz respectively. 

scholarly journals A Compact UWB Antenna with a Quarter-Wavelength Strip in a Rectangular Slot for 5.5 GHz Band Notch

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Pichet Moeikham ◽  
Chatree Mahatthanajatuphat ◽  
Prayoot Akkaraekthalin
Keyword(s):  
Frequency Band ◽  
Communication Systems ◽  
Notch Filter ◽  
Radiation Patterns ◽  
Frequency Range ◽  
Uwb Antenna ◽  
Antenna Structure ◽  
Rectangular Slot ◽  
Quarter Wavelength ◽  
Uwb Applications

The limitation of the electromagnetic interferences (EMIs) caused by UWB radiating sources into WLAN/WiMAX communication systems operating in the frequency band located around 5.5 GHz requires the adoption of appropriate design features. To this purpose, a notch filter integrated into an UWB antenna, which is able to ensure a better electrical insulation between the two mentioned communication systems with respect to that already presented by the authors Moeikham et al. (2011), is proposed in this paper. The proposed filter, consisting in a rectangular slot including a quarter-wavelength strip integrated on the lower inner edge of the UWB radiating patch, is capable of reducing the energy emission in the frequency range between 5.1 and 5.75 GHz resulting in lower EMIs with sensible electronic equipments working in this frequency band. The antenna structure has no need to be tuned after inserting the rectangle slot with a quarter-wavelength strip. The proposed antenna has potential to minimize the EMIs at a frequency range from 5.1 to 5.75 GHz. The radiation patterns are given nearly omnidirectional in plane and likely bidirectional in plane at all frequencies by the proposed antenna. Therefore, this antenna is suitable to apply for various UWB applications.

scholarly journals A Compact UWB Antenna with Independently Controllable Notch Bands

Sensors ◽  
2019 ◽  
Vol 19 (6) ◽  
pp. 1411 ◽  
Author(s):  
Amjad Iqbal ◽  
Amor Smida ◽  
Nazih Mallat ◽  
Mohammad Islam ◽  
Sunghwan Kim
Keyword(s):  
Group Delay ◽  
Ultra Wideband ◽  
Frequency Range ◽  
Uwb Antenna ◽  
Wireless System ◽  
Radiation Characteristics ◽  
Notched Band ◽  
Radiating Element ◽  
Wide Range ◽  
Shaped Section

A minimally-sized, triple-notched band ultra-wideband (UWB) antenna, useful for many applications, is designed, analyzed, and experimentally validated in this paper. A modified maple leaf-shaped main radiating element with partial ground is used in the proposed design. An E-shaped resonator, meandered slot, and U-shaped slot are implemented in the proposed design to block the co-existing bands. The E-shaped resonator stops frequencies ranging from 1.8–2.3 GHz (Advanced Wireless System (AWS1–AWS2) band), while the meandered slot blocks frequencies from 3.2–3.8 GHz (WiMAX band). The co-existing band ranging from 5.6–6.1 GHz (IEEE 802.11/HIPERLANband) is blocked by utilizing the U-shaped section in the feeding network. The notched bands can be independently controlled over a wide range of frequencies using specific parameters. The proposed antenna is suitable for many applications because of its flat gain, good radiation characteristics at both principal planes, uniform group delay, and non-varying transfer function ( S 21 ) for the entire UWB frequency range.

scholarly journals A novel UWB reconfigurable filtering antenna design with triple band-notched characteristics by using u-shaped coppers

2019 ◽  
Vol 14 (1) ◽  
pp. 267
Author(s):  
I.D. Saiful Bahri ◽  
Z. Zakaria ◽  
N. A. Shairi ◽  
N. Edward
Keyword(s):  
Current Distribution ◽  
Antenna Design ◽  
Frequency Range ◽  
Uwb Antenna ◽  
Pin Diodes ◽  
Band Frequency ◽  
Design Changes ◽  
X Band ◽  
Uwb Applications ◽  
Triple Band

<span>This paper proposed an UWB antenna with triple reconfigurable notch filters. By presenting there U-shaped coppers in the design, the potential triple interference in UWB applications can be rejected. Six PIN diodes are putted on the coppers to represent the OFF and ON tunable status in order to add reconfigurable characteristics to the UWB antenna. By using this ON and OFF tunable method, the current distribution of the proposed design changes and enables the antenna to have eight operation modes. The results prove that the proposed design can operate over the entire UWB frequency range (3.1 GHz to 10.6 GHz) and can filter out the target signals from the WLAN upper band (5.725 to 5.825 GHz), WLAN lower band (5.15 to 5.35 GHz) and X band frequency system (7.9 to 8.4 GHz) in one of the tunable configurations.</span>

scholarly journals A CPW-fed Irregular Shaped Hexagonal Patch Antenna with Elliptical Substrate for UWB Applications

2019 ◽  
Vol 9 (2) ◽  
pp. 373-376
Keyword(s):  
Patch Antenna ◽  
Impedance Matching ◽  
Ultra Wideband ◽  
Total Efficiency ◽  
Uwb Antenna ◽  
Radiation Characteristics ◽  
Wide Range ◽  
Uwb Applications ◽  
Novel Design ◽  
Peak Gain

A novel design of Ultra-Wideband (UWB) antenna with irregularly shaped hexagonal patch built on the elliptical-shaped FR-4 laminate with εr = 4.3 and tanδ = 0.025 is presented. The feed mechanism utilized in the structure proposed is modified co-planar waveguide (CPW), the feeding microstrip is tapered near the connecting edge of the patch for better impedance matching. The proposed antenna is compared with the traditional rectangular substrate and found that the elliptical substrate enhances the radiation characteristics of the antenna and is capable of functioning effectively in the range of 3.1 GHz-11.7 GHz, accompanied by the total efficiency > 86% across the whole FCC allocated UWB operating band. The antenna can be used for wide range of UWB applications as it exhibits good omnidirectional characteristics with a realized peak gain of 4.178dB and an average realized gain of 3.063dB. The simulation work of the antenna is accomplished using CST Studio (v. 2014).

scholarly journals Rectangular Ring Antenna Excited by Circular Disc Monopole for WiMAX System

2014 ◽  
Vol 2014 ◽  
pp. 1-7
Author(s):  
Souphanna Vongsack ◽  
Chuwong Phongcharoenpanich ◽  
Sompol Kosulvit ◽  
Kazuhiko Hamamoto ◽  
Toshio Wakabayashi
Keyword(s):  
Radiation Pattern ◽  
Circular Disc ◽  
Impedance Bandwidth ◽  
Frequency Range ◽  
Compact Size ◽  
Ring Antenna ◽  
Parametric Studies ◽  
Simulation Results ◽  
Wimax System ◽  
Good Agreement

This research presents a rectangular ring antenna excited by a circular disc monopole (CDM) mounted in front of a square reflector. The proposed antenna is designed to cover a frequency range of 2.300–5.825 GHz and thereby is suitable for WiMAX applications. Multiple parametric studies were carried out using the CST Microwave Studio simulation program. A prototype antenna was fabricated and experimented. The measurements were taken and compared with the simulation results, which indicates good agreement between both results. The prototype antenna produces an impedance bandwidth (|S11|< −10 dB) that covers the WiMAX frequency range and a constant unidirectional radiation pattern (θ=0°and∅=90°). The minimum and maximum gains are 3.7 and 8.7 dBi, respectively. The proposed antenna is of compact size and has good unidirectional radiation performance. Thus, it is very suitable for a multitude of WiMAX applications.

Compact stepped slot antenna for ultra-wideband applications

2021 ◽  
pp. 1-7
Author(s):  
B. Hammache ◽  
A. Messai ◽  
I. Messaoudene ◽  
T. A. Denidni
Keyword(s):  
Radiation Pattern ◽  
Impedance Matching ◽  
Ultra Wideband ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Back Side ◽  
Compact Size ◽  
Measurement Results ◽  
Operating Bandwidth ◽  
Uwb Applications

Abstract In this paper, a compact stepped slot antenna for ultra-wideband (UWB) applications is proposed. A very small size and UWB bandwidth operation are achieved by integrating a stepped slot in the back side of the antenna. This stepped slot is excited by using a 50 Ω-feed line in the top side of the antenna. The antenna is characterized by an impedance bandwidth between 3.05 GHz and more than 12 GHz. The dimensions of the antenna are 17 mm × 8 mm × 1.27 mm, which leads to the most compact size compared with other works in the literature. The integrated stepped slot is divided into additional elementary slots, where each elementary slot has a matching point. Adding these elementary slots allows to increase further the operating bandwidth. The radiation pattern of the compact stepped slot antenna is omnidirectional in the H-plane and bidirectional in the E-plane. The measurement results agree well with the simulated ones in terms of impedance matching and radiation pattern.

Performance Evaluation of Fractal Array Antenna for Small Satellite Applications

2016 ◽  
Vol 3 (2) ◽  
pp. 356 ◽  
Author(s):  
Yemane Ghebremedhin Teklehaimanot ◽  
Sinshaw Bekelle ◽  
Mohammed Ismail
Keyword(s):  
Antenna Array ◽  
Solar Panel ◽  
Patch Antennas ◽  
Small Satellite ◽  
Radiation Characteristics ◽  
Small Satellites ◽  
Microstrip Patch Antennas ◽  
Compact Size ◽  
High Efficient ◽  
Satellite Applications

<p class="Default">The possible antenna which can be integrated with relatively large flat structure of solar panel of small satellites is patch antenna. The main problem of common Microstrip patch antennas is that they only operate at one or two frequencies, restricting the number of bands that equipment is capable of supporting. Another issue is that, due to the very strict space that a solar panel has, setting up more antenna array is very difficult. To reduce these problems, the use of fractal shaped antennas integrated on solar cells will be analyzed. The small satellite applications demand a high efficient multi-band antenna with a very compact size. A 2x2 Sierpinski Fractal antenna array is modeled and simulated using HFSS. The proposed work has resulted in multiband operation 10.2 GHz and 18.3GHz with increased bandwidth and radiation characteristics betterment, with added advantage of light weight and smaller dimension which is important where cost to payload is a constraint in satellites.</p>

Sign in / Sign up

Export Citation Format

Share Document