scholarly journals Anodic Fabrication of Ti-Nb-Zr-O Nanotube Arrays

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Qiang Liu ◽  
Dongyan Ding ◽  
Congqin Ning
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Anodic Oxidation ◽  
Xrd Analysis ◽  
Lattice Parameter ◽  
Nanotube Arrays ◽  
X Ray ◽  
Diffraction Peaks ◽  
Scanning Electron ◽  
Zr Alloy

Highly ordered Ti-Nb-Zr-O nanotube arrays were fabricated through pulse anodic oxidation of Ti-Nb-Zr alloy in 1 M NaH2PO4containing 0.5 wt% HF electrolytes. The effect of anodization parameters and Zr content on the microstructure and composition of Ti-Nb-Zr-O nanotubes was investigated using a scanning electron microscope equipped with energy dispersive X-ray analysis. It was found that length of the Ti-Nb-Zr-O nanotubes increased with increase of Zr contents. The diameter and the length of Ti-Nb-Zr-O nanotubes could be controlled by pulse voltage. XRD analysis of Ti-Nb-Zr-O samples annealed at 500°C in air indicated that the (101) diffraction peaks shifted from 25.78° to 25.05° for annealed Ti-Nb-Zr-O samples with different Zr contents because of larger lattice parameter of Ti-Nb-Zr-O compared to that of undoped TiO2.

scholarly journals Supplementary X-ray studies of the Ni-Sn-Bi system

2007 ◽  
Vol 43 (2) ◽  
pp. 141-150 ◽  
Author(s):  
G.P. Vassilev ◽  
K.I. Lilova ◽  
J.C. Gachon
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Phase Equilibria ◽  
Ternary Compound ◽  
Approximate Formula ◽  
Ternary Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Diffraction Peaks ◽  
Scanning Electron

Phase equilibria were studied in the system Ni-Sn-Bi. Special attention has been paid to the identification of the recently found ternary phase. For this purpose samples were synthesized using intimately mixed powders. After annealing and quenching, all alloys were analyzed by scanning electron microscope and by X-ray diffraction. The results give evidences about the existence of a ternary compound with approximate formula Ni6Sn2Bi to Ni7Sn2Bi. Overlapping of some neighboring diffraction peaks of this phase with NiBi and Ni3Sn_LT is the reason for the difficulties related to the X-ray diffraction identification of the ternary phase.

The Effect of CaCO3 Addition on Physical Properties of ZnO-Based Crystal Glaze

2012 ◽  
Vol 620 ◽  
pp. 12-16 ◽  
Author(s):  
Abdul Rashid Jamaludin ◽  
Shah Rizal Kasim ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Calcium Carbonate ◽  
Scanning Electron Microscope ◽  
Physical Properties ◽  
Crystallization Temperature ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

The effects of calcium carbonate (CaCO3) addition on the physical properties of ZnO-based crystal glaze batches were investigated. Samples were fired at different gloss firing temperatures ranging from 1180-1220°C with 3 hours soaking at 1060°C crystallization temperature. X-ray diffraction (XRD) analysis identifiedthe crystal phase occurred as willemite (Zn2SiO4) and the scanning electron microscope (SEM) analysis indicated that willemite crystals are in the acicular needle like shape that formed spherulite. The intensities of willemite peaks decreased with CaCO3 addition and completely vanished at 5.0 wt% CaCO3. Varied formation of spherulites developed of the surface of crystal glaze as the flows of the glaze stretched further as the amount of CaCO3 increased.

Characterisation of Phases and Lattice Parameter in Eutectic and Hypoeutectic Al-Si-Mg-Ce Cast Alloy

2012 ◽  
Vol 620 ◽  
pp. 50-54
Author(s):  
A.S. Anasyida ◽  
Zuhailawati Hussain ◽  
Abdul Razak Daud ◽  
M.J. Ghazali
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Cast Alloy ◽  
Optical Microscope ◽  
Lattice Parameter ◽  
X Ray ◽  
Casting Technique ◽  
Conventional Casting ◽  
Ce Content ◽  
Scanning Electron

The purpose of this work is to understand the phases formation and lattice parameter changes with addition 0.6 to 2.7 wt.% in Al-Si-Mg-Ce cast alloy. Al-Si-Mg-Ce eutectic and hypoeutectic cast alloy were prepared by conventional casting technique. The alloys were investigated by using optical microscope, Scanning electron microscope (SEM) and X-Ray diffractometry (XRD). The addition of Ce resulted in precipitation of Al4Ce in eutectic cast alloy and CeMg2Si2 in hypoeutectic cast alloy. The lattice parameter of Al increases with increase in Ce content wheareas lattice parameter of Si phase decreases as the Ce content increases.

CuO Microspheres Synthesized via the Easy Hydrothermal Method

2012 ◽  
Vol 159 ◽  
pp. 84-87
Author(s):  
Xiao Ming Fu
Keyword(s):  
Electron Microscope ◽  
Reaction Time ◽  
Scanning Electron Microscope ◽  
Hydrothermal Method ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cuo Microspheres ◽  
Scanning Electron

CuO microspheres are successfully synthesized with CuCl2 as copper source and Na2CO3 as auxiliary salt at 240 °C for 24 h via the easy hydrothermal method. The phase and the morphologies of the samples have been characterized and analyzed by XRD (X-ray diffraction) and SEM (Scanning electron microscope), respectively. XRD analysis shows that the phase of as obtained samples is CuO. SEM analysis confirms that the increase of the reaction time, the reaction temperature and the auxiliary salt is propitious to synthesize CuO microspheres.

Synthesis of CuO Flower-Nanostructure via the Hydrothermal Method

2013 ◽  
Vol 873 ◽  
pp. 131-134
Author(s):  
Xiao Ming Fu ◽  
Jie Ren
Keyword(s):  
Electron Microscope ◽  
Reaction Time ◽  
Scanning Electron Microscope ◽  
Hydrothermal Method ◽  
Reaction Temperature ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

CuO flower-nanostructures are successfully synthesized with CuCl2 as copper source and Na2CO3 as auxiliary salt at 180 °C for 24 h via the simple hydrothermal method. The phase and the morphologies of the samples have been characterized and analyzed by XRD (X-ray diffraction) and SEM (Scanning electron microscope), respectively. XRD analysis shows that the phase of as obtained samples is CuO. SEM analysis confirms that the increase of the reaction temperature is propitious to synthesize CuO flower-nanostructures while the increase of the reaction time is not in favor of their synthesis. The influence of the increase of the auxiliary salt on the morphology of CuO flower-nanostructures is not remarkable. The mechanism of the formation of CuO flower-nanostructure is discussed.

The Influence of the Hydrothermal Temperature on the Morphologies of β-Ni(OH)2 Nanospheres and Nanoflakes

2012 ◽  
Vol 159 ◽  
pp. 376-379 ◽  
Author(s):  
Xiao Ming Fu
Keyword(s):  
Electron Microscope ◽  
High Temperature ◽  
Scanning Electron Microscope ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Hydrothermal Temperature ◽  
X Ray ◽  
Low Reaction Temperature ◽  
Scanning Electron

β-Ni(OH)2 nanospheres and nanoflakes have been successfully synthesized with nickel nitrate as nickel source and stronger ammonia water as precipitant via the hydrothermal method. The phase and the morphologies of the samples have been characterized and analyzed by XRD (X-ray diffraction) and SEM (Scanning electron microscope), respectively. XRD analysis shows that the phase of the samples is β-Ni(OH)2. SEM analysis confirms that the low reaction temperature is propitious to the synthesis of β-Ni(OH)2 nanospheres. However, The high temperature is in favor of the synthesis of β-Ni(OH)2 nanosflakes.

X-ray micro tomography in the scanning electron microscope

1978 ◽  
Vol 36 (1) ◽  
pp. 106-107 ◽  
Author(s):  
W. Brünger
Keyword(s):  
Electron Beam ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Target Surface ◽  
The Body ◽  
X Rays ◽  
Cross Sectional ◽  
X Ray ◽  
Micro Tomography ◽  
Scanning Electron

Reconstructive tomography is a new technique in diagnostic radiology for imaging cross-sectional planes of the human body /1/. A collimated beam of X-rays is scanned through a thin slice of the body and the transmitted intensity is recorded by a detector giving a linear shadow graph or projection (see fig. 1). Many of these projections at different angles are used to reconstruct the body-layer, usually with the aid of a computer. The picture element size of present tomographic scanners is approximately 1.1 mm2.Micro tomography can be realized using the very fine X-ray source generated by the focused electron beam of a scanning electron microscope (see fig. 2). The translation of the X-ray source is done by a line scan of the electron beam on a polished target surface /2/. Projections at different angles are produced by rotating the object.During the registration of a single scan the electron beam is deflected in one direction only, while both deflections are operating in the display tube.

PHAX-SCAN: Functional integration of a Scanning Electron Microscope and an energy-dispersive x-ray analyser

1989 ◽  
Vol 47 ◽  
pp. 56-57
Author(s):  
Marc H. Peeters ◽  
Max T. Otten
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
High Speed ◽  
High Performance ◽  
Functional Integration ◽  
Energy Dispersive ◽  
X Rays ◽  
X Ray ◽  
High Speed Analysis ◽  
Scanning Electron

Over the past decades, the combination of energy-dispersive analysis of X-rays and scanning electron microscopy has proved to be a powerful tool for fast and reliable elemental characterization of a large variety of specimens. The technique has evolved rapidly from a purely qualitative characterization method to a reliable quantitative way of analysis. In the last 5 years, an increasing need for automation is observed, whereby energy-dispersive analysers control the beam and stage movement of the scanning electron microscope in order to collect digital X-ray images and perform unattended point analysis over multiple locations.The Philips High-speed Analysis of X-rays system (PHAX-Scan) makes use of the high performance dual-processor structure of the EDAX PV9900 analyser and the databus structure of the Philips series 500 scanning electron microscope to provide a highly automated, user-friendly and extremely fast microanalysis system. The software that runs on the hardware described above was specifically designed to provide the ultimate attainable speed on the system.

PENGGUNAAN TiO2 PARTIKEL NANO HASIL SINTESIS BERBASIS AIR MENGGUNAKAN METODA SOL-GEL PADA BAHAN KAPAS SEBAGAI APLIKASI UNTUK TEKSTIL ANTI UV

Arena Tekstil ◽  
2013 ◽  
Vol 28 (1) ◽  
Author(s):  
Maya Komalasari ◽  
Bambang Sunendar
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sol Gel ◽  
Crosslinking Agent ◽  
X Ray Diffraction ◽  
Nano Tio2 ◽  
X Ray ◽  
Infra Red ◽  
Scanning Electron

Partikel nano TiO2 berbasis air dengan pH basa telah berhasil disintesis dengan menggunakan metode sol-gel dan diimobilisasi pada kain kapas dengan menggunakan kitosan sebagai zat pengikat silang. Sintesis dilakukan  dengan prekursor TiCl4 pada konsentrasi 0,3 M, 0,5 M dan 1 M, dan menggunakan templat kanji dengan proses kalsinasi pada suhu 500˚C selama 2 jam. Partikel nano TiO2 diaplikasikan ke kain kapas dengan metoda pad-dry-cure dan menggunakan kitosan sebagai crosslinking agent. Berdasarkan hasil Scanning Electron Microscope (SEM),diketahui bahwa morfologi partikel TiO2 berbentuk spherical dengan ukuran nano (kurang dari 100 nm). Karakterisasi X-Ray Diffraction (XRD) menunjukkan adanya tiga tipe struktur kristal utama, yaitu (100), (101) dan (102) dengan fasa kristal yang terbentuk adalah anatase dan rutile. Pada karakterisasi menggunakan SEM terhadap serbuk dari TiO2 yang telah diaplikasikan ke permukaan kain kapas, terlihat adanya imobilisasi partikel nano TiO2 melalui ikatan hidrogen silang dengan kitosan pada kain kapas. Hasil analisa tersebut kemudian dikonfirmasi dengan FTIR (Fourier Transform Infra Red) yang hasilnya memperlihatkan puncak serapan pada bilangan gelombang 3495 cm-1, 2546 cm-1, dan 511 cm-1,  yang masing-masing diasumsikan sebagai adanya vibrasi gugus fungsi O-H, N-H dan Ti-O-Ti. Hasil SEM menunjukkan pula bahwa kristal nano yang terbentuk diantaranya adalah fasa rutile , yang berdasarkan literatur terbukti dapatberfungsi sebagai anti UV.

Sign in / Sign up

Export Citation Format

Share Document