scholarly journals Design of 0.8–2.7 GHz High Power Class-F Harmonic-Tuned Power Amplifier with Parasitic Compensation Circuit

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Zhiqun Cheng ◽  
Xuefei Xuan ◽  
Huajie Ke ◽  
Guohua Liu ◽  
Zhihua Dong ◽  
...  
Keyword(s):  
Power Amplifier ◽  
High Power ◽  
High Efficiency ◽  
Impedance Matching ◽  
Harmonic Suppression ◽  
Compensation Circuit ◽  
Third Harmonic ◽  
The Third ◽  
Saturated Output Power ◽  
Class F

The design, implementation, and measurements of a high efficiency and high power wideband GaN HEMT power amplifier are presented. Package parasitic effect is reduced significantly by a novel compensation circuit design to improve the accuracy of impedance matching. An improved structure is proposed based on the traditional Class-F structure with all even harmonics and the third harmonic effectively controlled, respectively. Also the stepped-impedance matching method is applied to the third harmonic control network, which has a positive effect on the expansion bandwidth. CGH40025F power transistor is utilized to build the power amplifier working at 0.8 to 2.7 GHz, with the measured saturated output power 20–50 W, drain efficiency 52%–76%, and gain level above 10 dB. The second and the third harmonic suppression levels are maintained at −16 to −36 dBc and −16 to −33 dBc, respectively. The simulation and the measurement results of the proposed power amplifier show good consistency.

scholarly journals A 6 GHz Integrated High-Efficiency Class-F−1 Power Amplifier in 65 nm CMOS Achieving 47.8% Peak PAE

Electronics ◽  
2021 ◽  
Vol 10 (20) ◽  
pp. 2450
Author(s):  
Syed Muhammad Ammar Ali ◽  
S. M. Rezaul Hasan
Keyword(s):  
Power Amplifier ◽  
Peak Power ◽  
High Efficiency ◽  
Impedance Matching ◽  
Center Frequency ◽  
Dual Purpose ◽  
Power Added Efficiency ◽  
Harmonic Control ◽  
Saturated Output Power ◽  
Class F

This paper reports a “single-transistor” Class-F−1 power amplifier (PA) in 65 nm CMOS, which operates at the microwave center frequency of 6 GHz. The PA is loaded with a Class-F−1 harmonic control network, employing a new “parasitic-aware” topology deduced using a novel iterative algorithm. A dual-purpose output matching network is designed, which not only serves the purpose of output impedance matching, but also reinforces the harmonic control of the Class-F−1 harmonic network. This proposed PA yields a peak power-added efficiency (PAE) of 47.8%, which is one of the highest when compared to previously reported integrated microwave/millimeter-wave PAs in CMOS and SiGe technologies. The amplifier shows a saturated output power of 14.4 dBm along with an overall gain of 13.8 dB.

A 4.2-to-5.4 GHz stacked GaAs HBT power amplifier for C-band applications

Circuit World ◽  
2020 ◽  
Vol 46 (4) ◽  
pp. 243-248
Author(s):  
Min Liu ◽  
Panpan Xu ◽  
Jincan Zhang ◽  
Bo Liu ◽  
Liwen Zhang
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
High Power ◽  
High Efficiency ◽  
Common Source ◽  
Power Performance ◽  
Matching Network ◽  
Content Type ◽  
Power Added Efficiency ◽  
Saturated Output Power

Purpose Power amplifiers (PAs) play an important role in wireless communications because they dominate system performance. High-linearity broadband PAs are of great value for potential use in multi-band system implementation. The purpose of this paper is to present a cascode power amplifier architecture to achieve high power and high efficiency requirements for 4.2∼5.4 GHz applications. Design/methodology/approach A common emitter (CE) configuration with a stacked common base configuration of heterojunction bipolar transistor (HBT) is used to achieve high power. T-type matching network is used as input matching network. To increase the bandwidth, the output matching networks are implemented using the two L-networks. Findings By using the proposed method, the stacked PA demonstrates a maximum saturated output power of 26.2 dBm, a compact chip size of 1.17 × 0.59 mm2 and a maximum power-added efficiency of 46.3 per cent. The PA shows a wideband small signal gain with less than 3 dB variation over working frequency. The saturated output power of the proposed PA is higher than 25 dBm between 4.2 and 5.4 GHz. Originality/value The technology adopted for the design of the 4.2-to-5.4 GHz stacked PA is the 2-µm gallium arsenide HBT process. Based on the proposed method, a better power performance of 3 dB improvement can be achieved as compared with the conventional CE or common-source amplifier because of high output stacking impedance.

X-Band High-Efficiency High-Power GaN Power Amplifier Based on Edge-Triggered Gate Modulation

2020 ◽  
Vol 30 (9) ◽  
pp. 884-887
Author(s):  
Wen-Rao Fang ◽  
Wen-Hua Huang ◽  
Wen-Hui Huang ◽  
Jia-Wei Li ◽  
Chao Fu ◽  
...  
Keyword(s):  
Power Amplifier ◽  
High Power ◽  
High Efficiency ◽  
X Band

scholarly journals A 2.5-GHz 1-V High Efficiency CMOS Power Amplifier IC with a Dual-Switching Transistor and Third Harmonic Tuning Technique

Electronics ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 69 ◽  
Author(s):  
Taufiq Alif Kurniawan ◽  
Toshihiko Yoshimasu
Keyword(s):  
Power Amplifier ◽  
High Efficiency ◽  
Low Voltage ◽  
Supply Voltage ◽  
Drain Current ◽  
Cmos Technology ◽  
Back Gate ◽  
Third Harmonic ◽  
Power Added Efficiency ◽  
Switching Transistor

This paper presents a 2.5-GHz low-voltage, high-efficiency CMOS power amplifier (PA) IC in 0.18-µm CMOS technology. The combination of a dual-switching transistor (DST) and a third harmonic tuning technique is proposed. The DST effectively improves the gain at the saturation power region when the additional gain extension of the secondary switching transistor compensates for the gain compression of the primary one. To achieve high-efficiency performance, the third harmonic tuning circuit is connected in parallel to the output load. Therefore, the flattened drain current and voltage waveforms are generated, which in turn reduce the overlapping and the dc power consumption significantly. In addition, a 0.5-V back-gate voltage is applied to the primary switching transistor to realize the low-voltage operation. At 1 V of supply voltage, the proposed PA has achieved a power added efficiency (PAE) of 34.5% and a saturated output power of 10.1 dBm.

scholarly journals A Power Amplifier with Large High-Efficiency Range for 5G Communication

Sensors ◽  
2020 ◽  
Vol 20 (19) ◽  
pp. 5581
Author(s):  
Zhiwei Zhang ◽  
Zhiqun Cheng ◽  
Guohua Liu
Keyword(s):  
Output Power ◽  
Design Process ◽  
Power Amplifier ◽  
High Efficiency ◽  
New Method ◽  
Saturated Output Power ◽  
Doherty Power Amplifier ◽  
5G Communication

This paper presents a new method to design a Doherty power amplifier (DPA) with a large, high-efficiency range for 5G communication. This is through analyzing the drain-to-source capacitance (CDS) of DPAs, and adopting appropriate impedance of the peak device. A closed design process is proposed, to design the extended efficiency range DPA based on derived theories. For validation, a DPA with large efficiency range was designed and fabricated by using two equal devices. The measured results showed that the saturated output power was between 43.4 dBm and 43.7 dBm in the target band. Around 70% saturated drain efficiency is obtained with a gain of greater than 11 dB. Moreover, the obtained drain efficiency is larger than 50% at the 10 dB power back-off, when operating at 3.5 GHz. These superior performances illustrate that the implemented DPA can be applied well in 5G communication.

Sign in / Sign up

Export Citation Format

Share Document