scholarly journals Experimental Study on Structural Performance of RC Exterior Beam-Column Joints Retrofitted by Steel Jacketing and Haunch Element under Cyclic Loading Simulating Earthquake Excitation

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Cong-Thuat Dang ◽  
Ngoc-Hieu Dinh
Keyword(s):  
Cyclic Loading ◽  
Failure Load ◽  
Structural Performance ◽  
Dissipated Energy ◽  
Control Specimen ◽  
Seismic Capacity ◽  
Earthquake Excitation ◽  
Damage And Failure ◽  
Panel Zone ◽  
Energy Dissipation Capacity

Several retrofitting methods for reinforced concrete (RC) beam-column joints in old buildings without seismic details were developed. Four half-scale RC exterior beam-column joints were fabricated and tested under cyclic loading simulating earthquake excitation. The control specimen was designed to fail in joint shear. Two practical retrofitting strategies were applied to the control specimen which consider the architectural characteristic in real buildings, including steel jacketing and haunch retrofit solution. The structural performance of the test specimens was investigated in terms of various factors including damage and failure, load-drift relationship, ductility, dissipated energy, and strain profiles of longitudinal reinforcement. Experimental results confirmed that the proposed retrofit methods were shown to enhance the seismic capacity of the joints in terms of the strength, deformation capacity, and energy dissipation capacity while the shear deformation in the panel zone significantly reduced in comparison with the control specimen.

scholarly journals Experimental Analysis of Seismic Performance of Masonry Shear Wall Reinforced with PP-Band Mesh and Plastering Mortar under In-Plane Cyclic Loading

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Qiang Zhou ◽  
Lingyu Yang ◽  
Wenyang Zhao
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Bearing Capacity ◽  
Low Cost ◽  
Low Frequency ◽  
Masonry Wall ◽  
Ultimate Bearing Capacity ◽  
Masonry Walls ◽  
Seismic Capacity ◽  
Energy Dissipation Capacity

Masonry structures are widely used in developing countries due to their low cost and simple construction, especially in remote areas, where there are a large number of houses without seismic measures. These buildings are prone to collapse and cause a lot of casualties, even under the action of small earthquakes. For the reinforcement of this structure, a cheap, effective, and easy-to-construct reinforcement method is urgently needed. Therefore, this article studies the reinforcement method of polypropylene bands (PP-bands). We have carried out low-frequency cyclic loading tests for two PP-band reinforced masonry walls and two compared masonry walls. We mainly studied the influence of PP-band and different compressive strengths of plastering mortar on the masonry wall’s seismic capacity. The seismic indicators mainly studied in this article include ultimate bearing capacity, energy dissipation capacity, stiffness degradation, and hysteresis characteristics. The experimental results show that the PP-band can greatly enhance the seismic capacity of the masonry wall. The ultimate bearing capacity, energy dissipation capacity, and displacement ductility of the PP-band reinforced wall are increased by 38%–48%, 22%–47%, and 138%–226%.

scholarly journals Experimental Study on Friction Sliding Performance of Rubber Bearings in Bridges

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Yue Li ◽  
Qiqi Wu
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Shear Deformation ◽  
Shear Failure ◽  
Good Condition ◽  
Dissipated Energy ◽  
Hysteresis Curves ◽  
Rubber Layer ◽  
Energy Dissipation Capacity ◽  
Rubber Bearings

To fully ascertain the ultimate shear failure state and the friction sliding performance of laminated rubber bearings in bridges, a series of cyclic loading tests were conducted. The energy dissipation characteristics of the laminated rubber bearings with two end plates, rubber bearings with unilateral friction sliding, and lead rubber bearing (LRB) under low-frequency cyclic loads were compared and analyzed. The results showed the following. (1) The ultimate shear deformation of the rubber bearings with two end plates could reach 300% to 400% of the rubber layer thickness. The energy dissipation capacity of the bearings was weak, and the hysteresis curves presented narrow zonal shapes. (2) The rubber bearings with unilateral friction sliding had similar energy dissipation capacities compared to the LRB. With the increase of the sliding distance, the dissipated energy continuously enlarged. The shear deformation of the bearing was no longer increased after reaching the maximum. After the test, the bearings remained in a good condition. The hysteresis curves of the load and displacement presented bilinear shapes. (3) Under the cyclic loading, the energy dissipation capacity of LRB was stable. The hysteresis curves of LRB were always fuller than the laminated rubber bearings.

Structural Performance of Disaster Relief Housing Units Subjected to Cyclic Loading

2013 ◽  
Vol 684 ◽  
pp. 111-115
Author(s):  
Tae Hyu Ha ◽  
Dae Jin Kim ◽  
Choong Hee Han
Keyword(s):  
Cyclic Loading ◽  
Disaster Relief ◽  
Housing Unit ◽  
Structural Performance ◽  
Test Results ◽  
Wall Panel ◽  
Nonstructural Components ◽  
Steel Angle ◽  
Lateral Strength ◽  
Energy Dissipation Capacity

In this paper, a new disaster relief housing unit is proposed, and its structural performance under cyclic loading conditions is investigated. This housing unit is composed of a series of identical unit wall panels, which are made up of steel angle frames, steel rods for diagonal bracing and sheeting elements. The lateral load resisting capacity of only a single wall panel is examined by performing a test on three specimens. The theoretical lateral strength of the wall panel is estimated and compared with the test results. The contribution of sheeting elements, generally treated as nonstructural components, is considered, and the energy dissipation capacity of the proposed unit is also evaluated. The results of the test show that the addition of sheeting elements is helpful to enhance the peak lateral strength of the panel frame and the steel diagonal bracing is very effective in enhancing the peak strength of the unit wall panel at initial stages, but not the overall ductility of the structure.

Stress Transferring Mechanism and the Bearing Capacity of Joints between Concrete-Filled Square Steel Tubular Special-Shaped Columns and Steel Beams

2011 ◽  
Vol 105-107 ◽  
pp. 926-930
Author(s):  
Xi Chen
Keyword(s):  
Shear Strength ◽  
Energy Dissipation ◽  
Structural Performance ◽  
Steel Beams ◽  
Steel Beam ◽  
Loading Capacity ◽  
Panel Zone ◽  
Strong Energy ◽  
New Type ◽  
Energy Dissipation Capacity

In recent years, a new type of frame consisting of steel beam and concrete-filled square steel tubular special-shaped column is increasingly widespread. Compared with the joint of ordinary reinforced concrete special shaped frame, the joint between concrete-filled square steel tubular special-shaped columns and steel beams has the advantage of better ductility, higher loading capacity, uncomplicated reinforcement disposing and convenience in construction. This paper indicates that the joint has strong energy dissipation capacity and high loading capacity, and the use of diaphragm is effective to enhance the structural performance of the joints. Stress transferring mechanism in the joints is discussed, and the calculating model of the shear strength of panel zone is established. This study is helpful for further study of the design and use of the joint between concrete-filled square steel tubular special-shaped columns and steel beams.

scholarly journals Experiment on Behavior of a New Connector Used in Bamboo (Timber) Frame Structure under Cyclic Loading

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Junwen Zhou ◽  
Dongsheng Huang ◽  
Chun Ni ◽  
Yurong Shen ◽  
Longlong Zhao
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Cyclic Load ◽  
Mechanical Performance ◽  
Frame Structure ◽  
Structural Performance ◽  
Timber Frame ◽  
Steel Column ◽  
Energy Dissipation Capacity ◽  
Energy Dissipation Coefficient

Connection is an important part of the bamboo and timber structure, and it directly influences the overall structural performance and safety. Based on a comprehensive analysis of the mechanical performance of several wood connections, a new connector for the bamboo (timber) frame joint was proposed in this paper. Three full-scale T-type joint specimens were designed to study the mechanical performance under cyclic loading. The thickness of the hollow steel column was different among three specimens. The specimens were loaded under displacement control with a rate of 10 mm per minute until the specimens reach failure. It was observed that the failures of three specimens were caused by the buckling of flanges in the compression and that the steel of connections does not yield. The load-displacement hysteretic curve for three specimens is relatively plump, and the stiffness of connection degenerates with the increasing of cyclic load. The maximum rotation is 0.049 rad, and the energy dissipation coefficient is 1.77. The thickness of the hollow steel column of the connector has significant impact on the energy dissipation capacity and the strength of the connection. A simplified moment-rotation hysteresis model for the joint was proposed.

scholarly journals Experimental/Numerical Evaluation of Steel Trapezoidal Corrugated Infill Panels with an Opening

2021 ◽  
Vol 11 (7) ◽  
pp. 3275
Author(s):  
Majid Yaseri Gilvaee ◽  
Massood Mofid
Keyword(s):  
Energy Dissipation ◽  
Ultimate Strength ◽  
Steel Plate ◽  
Shear Walls ◽  
Experimental Results ◽  
Structural Performance ◽  
Initial Stiffness ◽  
Infill Panels ◽  
Energy Dissipation Capacity ◽  
Ductility Ratio

This paper investigates the influence of an opening in the infill steel plate on the behavior of steel trapezoidal corrugated infill panels. Two specimens of steel trapezoidal corrugated shear walls were constructed and tested under cyclic loading. One specimen had a single rectangular opening, while the other one had two rectangular openings. In addition, the percentage of opening in both specimens was 18%. The initial stiffness, ultimate strength, ductility ratio and energy dissipation capacity of the two tested specimens are compared to a specimen without opening. The experimental results indicate that the existence of an opening has the greatest effect on the initial stiffness of the corrugated steel infill panels. In addition, the experimental results reveal that the structural performance of the specimen with two openings is improved in some areas compared to the specimen with one opening. To that end, the energy dissipation capacity of the specimen with two openings is obtained larger than the specimen with one opening. Furthermore, a number of numerical analyses were performed. The numerical results show that with increasing the thickness of the infill plate or using stiffeners around the opening, the ultimate strength of a corrugated steel infill panel with an opening can be equal to or even more than the ultimate strength of that panel without an opening.

Analysis the characteristic of energy and damage of coal-rock composite structure under cycle loading

2021 ◽  
Author(s):  
Tan Li ◽  
Guangbo Chen ◽  
Zhongcheng Qin ◽  
Qinghai Li
Keyword(s):  
Cyclic Loading ◽  
Elastic Energy ◽  
Composite Structure ◽  
Calculation Method ◽  
Composite Structures ◽  
Damage Variable ◽  
Dissipated Energy ◽  
Height Ratio ◽  
Coal Rock ◽  
The Stability

Abstract The stability of coal-rock composite structures is of great significance to coal mine safety production. To study the stability and deformation failure characteristics of the coal-rock composite structure, the uniaxial cyclic loading tests of the coal-rock composite structures with different coal-rock height ratios were carried out. Lithology and coal-rock height ratio play an important role in the energy dissipation of coal-rock composite structures. The higher the coal-rock height ratio, the greater the average elastic energy and dissipated energy produced per cycle of coal-rock composite structures, the smaller the total elastic energy and dissipated energy produced in the process of cyclic loading. Based on the difference of damage variables calculated by dissipative energy method and acoustic emission method, a more sensitive joint calculation method for calculating damage variable was proposed. The joint damage variable calculation method can more accurately and sensitively reflect the damage of coal-rock composite structure under cyclic loading. The macroscopic crack first appears in the coal specimen in the coal-rock composite structure, the degree of broken coal specimens in the composite structure is inversely proportional to the coal-rock height ratio. The strength and deformation characteristics of the coal-rock composite structure are mainly affected by coal sample in the composite structure.

Seismic capacity estimation of a reinforced concrete containment building considering bidirectional cyclic effect

2018 ◽  
Vol 22 (5) ◽  
pp. 1106-1120
Author(s):  
Zhi Zheng ◽  
Changhai Zhai ◽  
Xu Bao ◽  
Xiaolan Pan
Keyword(s):  
Reinforced Concrete ◽  
Dynamic Analysis ◽  
Geometric Mean ◽  
Pushover Analysis ◽  
Incremental Dynamic Analysis ◽  
Dissipated Energy ◽  
Seismic Capacity ◽  
Capacity Estimation ◽  
Earthquake Intensity ◽  
Static Pushover Analysis

This study serves to estimate the seismic capacity of the reinforced concrete containment building considering its bidirectional cyclic effect and variations of energy. The implementation of the capacity estimation has been performed by extending two well-known methods: nonlinear static pushover and incremental dynamic analysis. The displacement and dissipated energy demands are obtained from the static pushover analysis considering bidirectional cyclic effect. In total, 18 bidirectional earthquake intensity parameters are developed to perform the incremental dynamic analysis for the reinforced concrete containment building. Results show that the bidirectional static pushover analysis tends to decrease the capacity of the reinforced concrete containment building in comparison with unidirectional static pushover analysis. The 5% damped first-mode geometric mean spectral acceleration strongly correlates with the maximum top displacement of the containment building. The comparison of the incremental dynamic analysis and static pushover curves is employed to determine the seismic capacity of the reinforced concrete containment building. It is concluded that bidirectional static pushover and incremental dynamic analysis studies can be used in performance evaluation and capacity estimation of reinforced concrete containment buildings under bidirectional earthquake excitations.

Sign in / Sign up

Export Citation Format

Share Document