scholarly journals Experimental Research on Frost Heave Characteristics of Gravel Soil and Multifactor Regression Prediction

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Xiaoyong Long ◽  
Guoping Cen ◽  
Liangcai Cai ◽  
Yue Chen
Keyword(s):  
Moisture Content ◽  
Initial Moisture Content ◽  
Clay Content ◽  
Open Water ◽  
Frost Heave ◽  
Frost Heaving ◽  
Gravel Soil ◽  
Closed Water ◽  
Multifactor Regression ◽  
Insight Into

Gravel soil is usually considered to be insensitive to frost heave. However, many frost heave deformations of foundation in seasonal frozen region indicate that gravel soil may also produce frost heave under certain special conditions. In order to gain a deep insight into the frost heave characteristics of gravel soil, a series of laboratory experiments on one-dimensional frost heave were conducted under the open- and closed-water replenishing condition using an improved experiment apparatus. The influence of various factors including initial moisture content, clay content, compactness, overlying load, and water replenishing on frost-heaving ratio of gravel soil were analyzed. And the basic frost heave characteristics including frost heave amount, frost heave speed, frozen depth, freezing speed, and moisture content distribution after freezing in a gravel soil sample were analyzed. The corresponding mechanisms were also discussed. Results showed that in the open water replenishing condition, there exists a linear relationship between initial moisture content, overlying load, and frost-heaving ratio and a quadratic polynomial relationship between clay content, compactness, and frost-heaving ratio. Frost-heaving ratio in the open water replenishing condition can be found to increase over three times than that under the closed water replenishing condition. Multifactor regression empirical formula was obtained by multiple regression analysis to predict the frost-heaving ratio of gravel soil under certain collocation of factors and levels under the closed water replenishing condition. The significant effects on frost-heaving ratio were, in order, water replenishing > initial moisture content > clay content > compactness > overlying load.

scholarly journals Study on collapsibility of typical structural loess by multi-parameter comparative analysis

2021 ◽  
Vol 293 ◽  
pp. 01032
Author(s):  
Liu Hongcheng ◽  
Lu Changwei ◽  
Wang Yinxia ◽  
Song Yi ◽  
Guan Xiangfeng ◽  
...  
Keyword(s):  
Particle Size ◽  
Comparative Analysis ◽  
Moisture Content ◽  
Composite Structure ◽  
Structural Parameters ◽  
Initial Moisture Content ◽  
Clay Content ◽  
Dry Density ◽  
Particle Content ◽  
Multiple Groups

To study the collapsibility of typical loess and its influencing factors in different areas, the samples in Jingyang, Lanzhou and Yili were studied. The correlation between initial moisture content, dry density, composition of particle size, structural parameters and the coefficient of subsidence is analyzed. The results show that: the coefficient of collapsibility is negatively correlated with the initial moisture content and dry density. In the experiments of multiple groups, the collapsibility coefficient has a certain correlation with the clay content, but not a uniform correlation with the particle content. The collapse coefficient is approximately positively correlated with the composite structure potential.

Energetic relationships for crushing of soil clods

2006 ◽  
Vol 2 (1) ◽  
pp. 51-72
Author(s):  
István Patay ◽  
Virág Sándor
Keyword(s):  
Moisture Content ◽  
Specific Energy ◽  
Soil Moisture Content ◽  
Energy Requirement ◽  
Clay Content ◽  
Clay Soils ◽  
Rigid Support ◽  
Soil Plasticity ◽  
Specific Energy Requirement ◽  
The Relationship

Clod crushing is a principal problem with soils of high clay content. Therefore, there is a need for determining the conditions for clod breaking and clod crushing. The objective of the work was to develop a special purpose tool for single clod breaking both by rigid support of the clod and by a single clod supported by soil and to develop a machine for clod crushing. Furthermore, the purpose was to determine the relationship between the specific energy requirement for clod crushing in the function of soil plasticity and the soil moisture content by the means of the developed tool and machine. The main result of the experiments is summarized in a 3D diagram where the specific energy requirement for soil clod crushing is given in the function of the moisture content and the plasticity index for different clay soils.

Examination of Tobacco Hygroscopicity / Über die Hygroskopizität des Tabaks

1965 ◽  
Vol 3 (1) ◽  
Author(s):  
L. Hübschen
Keyword(s):  
Moisture Content ◽  
Sorption Isotherm ◽  
Initial Moisture Content

AbstractThe present paper shows the detectable factors on which a sorption isotherm depends. Even if it is well-known that a sorption isotherm is most essentially conditioned by influences of the respective tobacco variety, other factors, such as temperature, initial moisture content, or fibre dimension, play a part as well. In general, a sorption isotherm constitutes a ''summation'' of such factors and, in the end, a combination of desorption and adsorption if the tobacco is dried or moistened from the average commercial moisture content. The tobacco hysteresis is experimentally investigated and discussed

Pengeringan Biji Kakao dengan Pengering Surya Tipe Terowong Berpenggerak Sel Fotovoltaik di Manokwari

Agrotek ◽  
2018 ◽  
Vol 2 (6) ◽  
Author(s):  
Wilson Palelingan Aman
Keyword(s):  
Moisture Content ◽  
Performance Test ◽  
Initial Moisture Content ◽  
Maximum Temperature ◽  
Photovoltaic Module ◽  
Cocoa Beans ◽  
Drying Time ◽  
Tunnel Dryer ◽  
Heat Collector ◽  
New Construction

<em>A research about cocoa beans drying used solar tunnel dryer with photovoltaic module driven have conducted in Manokwari. Solar tunnel dryer used in this research adapted from type Hohenheim with photovoltaic module and integrated air heat collector has been installed at the Department of Agricultural Technology, Papua State University Manokwari to dried cocoa beans. The objectives of this research were to design solar tunnel dryer and evaluate it�s performance in dryed cocoa beans. The result obtained was a new construction of solar tunnel dryer for cocoa beans with dimensions 6 m of length and 0,9 m of wide. The dryer completed with photovoltaic module to drive the blowers of hot drying air. �Performance test of the dryer showed that drying of 10 kg of cocoa beans with initial moisture content about 70% wet basis needed 13 hours of drying time to achieved final moisture content about 7,17% wet basis. The drying time achieved was faster compared than traditional solar drying that needed 20 hours of drying time. The maximum temperature achieved in drying chamber was 60 <sup>o</sup>C.</em>

scholarly journals Wood Chip Drying through the Using of a Mobile Rotary Dryer

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1590 ◽  
Author(s):  
Angelo Del Giudice ◽  
Andrea Acampora ◽  
Enrico Santangelo ◽  
Luigi Pari ◽  
Simone Bergonzoli ◽  
...  
Keyword(s):  
Moisture Content ◽  
Power Plants ◽  
Black Locust ◽  
Thermal Power ◽  
Initial Moisture Content ◽  
Wood Chip ◽  
Wood Chips ◽  
Cocurrent Flow ◽  
Drying Process ◽  
Rotary Dryer

Drying is a critical point for the exploitation of biomass for energy production. High moisture content negatively affects the efficiency of power generation in combustion and gasification systems. Different types of dryers are available however; it is known that rotary dryers have low cost of maintenance and consume 15% and 30% less in terms of specific energy. The study analyzed the drying process of woody residues using a new prototype of mobile rotary dryer cocurrent flow. Woodchip of poplar (Populus spp.), black locust (Robinia pseudoacacia L.), and grapevine (Vitis vinifera L.) pruning were dried in a rotary drier. The drying cycle lasted 8 h for poplar, 6 h for black locust, and 6 h for pruning of grapevine. The initial biomass had a moisture content of around 50% for the poplar and around 30% for grapevine and black locust. The study showed that some characteristics of the biomass (e.g., initial moisture content, particle size distribution, bulk density) influence the technical parameters (i.e., airflow temperature, rate, and speed) of the drying process and, hence, the energy demand. At the end of the drying process, 17% of water was removed for poplar wood chips and 31% for grapevine and black locust wood chips. To achieve this, result the three-biomass required 1.61 (poplar), 0.86 (grapevine), and 1.12 MJ kgdry solids−1 (black locust), with an efficiency of thermal drying (η) respectively of 37%, 12%, and 27%. In the future, the results obtained suggest an increase in the efficiency of the thermal insulation of the mobile dryer, and the application of the mobile dryer in a small farm, for the recovery of exhaust gases from thermal power plants.

scholarly journals Effects of microwave irradiation on the moisture content of various wood chip fractions obtained from different tree species

2021 ◽  
Vol 67 (1) ◽  
Author(s):  
Monika Aniszewska ◽  
Krzysztof Słowiński ◽  
Ewa Tulska ◽  
Witold Zychowicz
Keyword(s):  
Moisture Content ◽  
Microwave Irradiation ◽  
Microwave Power ◽  
Irradiation Time ◽  
Initial Moisture Content ◽  
Radiant Energy ◽  
Wood Chip ◽  
Wood Chips ◽  
Chip Size ◽  
Drying Rates

AbstractThe paper proposes the use of microwave irradiation to lower the initial moisture content of wood chips. The study involved willow and fir chips fractionated by means of a sieve separator and unfractionated ash chips. The wood chips were exposed to a constant microwave power of 800 W for 30 s, 60 s, 120 s and 180 s. The chips were weighed before and after irradiation to measure loss of moisture. It was found that the decline in moisture content increased with wood chip size for a given irradiation time and microwave power. The initial moisture content of wood chips was not found to significantly affect loss of moisture as the drying rates of wood chips with higher and lower moisture content exposed to microwaves were not statistically different. The results showed that irradiation intensity increased with the time of exposure to microwaves and unit radiant energy per unit of evaporated moisture decreased with increasing wood chip size in the 3.15–31.50 mm range.

scholarly journals Cherry Tomato Drying: Sun versus Convective Oven

Horticulturae ◽  
2021 ◽  
Vol 7 (3) ◽  
pp. 40
Author(s):  
Vincenzo Alfeo ◽  
Diego Planeta ◽  
Salvatore Velotto ◽  
Rosa Palmeri ◽  
Aldo Todaro
Keyword(s):  
Moisture Content ◽  
Initial Moisture Content ◽  
Drying Process ◽  
Drying Time ◽  
Oven Drying ◽  
Sun Drying ◽  
Different Temperatures ◽  
Final Water Content ◽  
Drying Curves ◽  
Drying Conditions

Solar drying and convective oven drying of cherry tomatoes (Solanum lycopersicum) were compared. The changes in the chemical parameters of tomatoes and principal drying parameters were recorded during the drying process. Drying curves were fitted to several mathematical models, and the effects of air temperature during drying were evaluated by multiple regression analyses, comparing to previously reported models. Models for drying conditions indicated a final water content of 30% (semidry products) and 15% (dry products) was achieved, comparing sun-drying and convective oven drying at three different temperatures. After 26–28 h of sun drying, the tomato tissue had reached a moisture content of 15%. However, less drying time, about 10–11 h, was needed when starting with an initial moisture content of 92%. The tomato tissue had high ORAC and polyphenol content values after convective oven drying at 60 °C. The dried tomato samples had a satisfactory taste, color and antioxidant values.

Effect of initial moisture content and sample storage duration on compost stability using the ORG0020 dynamic respiration test

2021 ◽  
Vol 125 ◽  
pp. 215-219 ◽  
Author(s):  
Nisha N. Gurusamy ◽  
Natalie Puffer ◽  
Coen de Jongh ◽  
Cristina Rodriguez Gil ◽  
Thomas J. Aspray
Keyword(s):  
Moisture Content ◽  
Initial Moisture Content ◽  
Sample Storage ◽  
Storage Duration ◽  
Compost Stability

scholarly journals Comparison of Geotechnical Properties of Laterite, Kaolin and Peat

2015 ◽  
Vol 773-774 ◽  
pp. 1438-1442 ◽  
Author(s):  
Siti Aimi Nadia Mohd Yusoff ◽  
I. Bakar ◽  
Devapriya Chitral Wijeyesekera ◽  
Adnan Zainorabidin ◽  
Aziman Madun
Keyword(s):  
Specific Gravity ◽  
Moisture Content ◽  
Initial Moisture Content ◽  
General Information ◽  
Geotechnical Properties ◽  
Grain Size Analysis ◽  
Size Analysis ◽  
Proctor Test ◽  
Construction Operation ◽  
Soil Behaviour

This paper compares some geotechnical properties of Kaolin, Laterite and Peat. Laterite was collected from Bukit Banang while Peat sample was collected from Parit Nipah, both locations were in Batu Pahat, Johor. Meanwhile, kaolin that was used in this research was manufactured kaolin. These soil samples were subjected to routine laboratory analysis and resulting data were analyzed statistically using a correlation analysis. A laboratory testing program consists of “Basic properties test” to obtain general information on the materials (e.g Natural moisture content, Atterberg Limit, Specific gravity, grain size analysis, chemical composition and pH) and “Geotechnical properties tests” to measure specific properties that characterize soil behaviour for design and constructability assessments (e.g Standard Proctor Test, Unconfined Compressive Strength and CBR).The results showed that the Natural/initial moisture content for laterite, peat and kaolin is 22.54%, 480.61% and 0.22% respectively. Meanwhile Specific gravity for each soil was in the range 1.50-2.79.It was also found that the pH of all soil is acidic which lay in the range of 3.76-5.95.The UCS for the optimally compacted sample of laterite is 445.77 kPa, kaolin is 199.23 kPa and for peat is 58.70 kPa. This paper summarizes the result of analysis performed on all tests conducted. Based on the results, the geotechnical property of the soil is a highly dependent with the type of soil and therefore, determining the soil characterization and the soil strength should be considered during the planning phase of any earthwork construction operation.

Sign in / Sign up

Export Citation Format

Share Document