scholarly journals Effect of the Reduction Temperature of PdAg Nanoparticles during the Polyol Process in the Ethanol Electrooxidation Reaction

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
R. Carrera-Cerritos ◽  
C. Salazar-Hernandez ◽  
I. R. Galindo-Esquivel ◽  
R. Fuentes-Ramirez
Keyword(s):  
Polyol Process ◽  
Reduction Temperature ◽  
Ethanol Electrooxidation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Current Density ◽  
Transmission Electron ◽  
Maximum Current ◽  
Catalytic Stability ◽  
Electrochemical Evaluation

This work reports the effect of reduction temperature during the synthesis of PdAg catalysts through the polyol process and their evaluation in the ethanol electrooxidation reaction (EOR). The characterization was performed using Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD). The electrochemical evaluation for the ethanol electrooxidation reaction was implemented in alkaline medium using chronoamperometry (CA) and cyclic voltammetry (CV). An important effect of the reduction temperature on electroactivity and catalytic stability was observed: both the maximum current density and the catalytic stability were higher in the catalyst synthesized at the highest temperature (135°C). This performance was associated with the extent of the interaction between Pd and Ag which was measured in terms of the structural expansion of Pd.

EXAFS Study on Nanosized PtRu Catalyst for Direct Methanol Fuel Cell

2005 ◽  
Vol 900 ◽  
Author(s):  
Hiroaki Nitani ◽  
Takahiro Ono ◽  
Yusuke Honda ◽  
Akiko Koizumi ◽  
Takashi Nakagawa ◽  
...  
Keyword(s):  
Precursor Solution ◽  
Polyol Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Direct Methanol ◽  
Ptru Catalyst ◽  
Exafs Study ◽  
Ptru Catalysts ◽  
X Ray Absorption

ABSTRACTNano-sized PtRu catalysts supported on carbon nanoparticles were synthesized by a polyol process. The PtRu catalyst prepared at pH=3 indicated higher catalysis for methanol oxidation than one prepared at pH=5.5. The samples were analyzed by techniques of the extended X-ray absorption fine structure (EXAFS), transmission electron microscope (TEM), X-ray diffraction (XRD) and X-ray fluorescence (XRF). Their results showed that the pH of the precursor solution during the polyol process affected the substructure of the PtRu nanoparticles. The correlation of the substructure with the catalytic activity was studied.

Synthesis of Fe-Co Nanobars Using Sodium Sulfite Assisted Polyol Process and their Structural and Magnetic Studies

2011 ◽  
Vol 15 ◽  
pp. 21-28 ◽  
Author(s):  
G. Suresh ◽  
P. Saravanan ◽  
D. Rajan Babu
Keyword(s):  
Cetyltrimethylammonium Bromide ◽  
Sodium Sulfite ◽  
Polyol Process ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
Magnetic Studies ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Co Nanoparticles

We report the synthesis of soft magnetic Fe-Co nanobars by an improved polyol process using cetyltrimethylammonium bromide (CTAB) as stabilizer. The synthesized samples were studied by using Transmission Electron Microscopy. The Fe-Co nanoparticles were characterized by X-ray diffraction, UV-Vis spectroscopy, Fourier transform infrared spectroscopy and Vibrating Sample Magnetometer. The Fe-Co nanobars showed prominent UV-VIS absorption at 371 nm. This report discusses the effect of sodium sulfite and CTAB on the synthesis of Fe-Co nanoparticles.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

A High Resolution Study of G.P. Zones in Aluminum - 4.2 at % Silver

1982 ◽  
Vol 40 ◽  
pp. 722-723 ◽  
Author(s):  
R. Gronsky
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Resolution ◽  
Computer Simulations ◽  
Structural Characteristics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Resolution Study

The phenomenon of clustering in Al-Ag alloys has been extensively studied since the early work of Guinierl, wherein the pre-precipitation state was characterized as an assembly of spherical, ordered, silver-rich G.P. zones. Subsequent x-ray and TEM investigations yielded results in general agreement with this model. However, serious discrepancies were later revealed by the detailed x-ray diffraction - based computer simulations of Gragg and Cohen, i.e., the silver-rich clusters were instead octahedral in shape and fully disordered, atleast below 170°C. The object of the present investigation is to examine directly the structural characteristics of G.P. zones in Al-Ag by high resolution transmission electron microscopy.

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

Transmission electron microscope studies in special ceramics

1978 ◽  
Vol 36 (1) ◽  
pp. 268-269
Author(s):  
A. Zangvil ◽  
L.J. Gauckler ◽  
G. Schneider ◽  
M. Rühle
Keyword(s):  
Phase Diagrams ◽  
Crystal Structures ◽  
Thin Foil ◽  
Limited Extent ◽  
Complex Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Microscopes ◽  
Lattice Resolution

The use of high temperature special ceramics which are usually complex materials based on oxides, nitrides, carbides and borides of silicon and aluminum, is critically dependent on their thermomechanical and other physical properties. The investigations of the phase diagrams, crystal structures and microstructural features are essential for better understanding of the macro-properties. Phase diagrams and crystal structures have been studied mainly by X-ray diffraction (XRD). Transmission electron microscopy (TEM) has contributed to this field to a very limited extent; it has been used more extensively in the study of microstructure, phase transformations and lattice defects. Often only TEM can give solutions to numerous problems in the above fields, since the various phases exist in extremely fine grains and subgrain structures; single crystals of appreciable size are often not available. Examples with some of our experimental results from two multicomponent systems are presented here. The standard ion thinning technique was used for the preparation of thin foil samples, which were then investigated with JEOL 200A and Siemens ELMISKOP 102 (for the lattice resolution work) electron microscopes.

A TEM investigation of a hyper-eutectic lead-tin alloy

1988 ◽  
Vol 46 ◽  
pp. 562-563
Author(s):  
John A. Sutliff
Keyword(s):  
Volume Diffusion ◽  
Eutectic Mixture ◽  
Precipitation Reaction ◽  
Directionally Solidified ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Diffusion Controlled ◽  
Discontinuous Precipitation Reaction ◽  
Controlled Precipitation

Near-eutectic Pb-Sn alloys are important solders used by the electronics industry. In these solders, the eutectic mixture, which solidifies last, is the important microstructural consituent. The orientation relation (OR) between the eutectic phases has previously been determined for directionally solidified (DS) eutectic alloys using x-ray diffraction or electron chanelling techniques. In the present investigation the microstructure of a conventionally cast, hyper-eutectic Pb-Sn alloy was examined by transmission electron microscopy (TEM) and the OR between the eutectic phases was determined by electron diffraction. Precipitates of Sn in Pb were also observed and the OR determined. The same OR was found in both the eutectic and precipitation reacted materials. While the precipitation of Sn in Pb was previously shown to occur by a discontinuous precipitation reaction,3 the present work confirms a recent finding that volume diffusion controlled precipitation can also occur.Samples that are representative of the solder's cast microstructure are difficult to prepare for TEM because the alloy is multiphase and the phases are soft.

The Effect of the Microstructure of Diffusion Barriers on the Palladium Activation for Electroless Copper Deposition

2002 ◽  
Vol 716 ◽  
Author(s):  
Seok Woo Hong ◽  
Yong Sun Lee ◽  
Ki-Chul Park ◽  
Jong-Wan Park
Keyword(s):  
Electron Microscopy ◽  
Diffusion Barriers ◽  
Copper Deposition ◽  
X Ray Diffraction ◽  
Plan View ◽  
X Ray ◽  
Transmission Electron ◽  
Electroless Copper ◽  
Sheet Resistance Measurement ◽  
Scanning Electron

AbstractThe effect of microstructure of dc magnetron sputtered TiN and TaN diffusion barriers on the palladium activation for autocatalytic electroless copper deposition has been investigated by using X-ray diffraction, sheet resistance measurement, field emission scanning electron microscopy (FE-SEM) and plan view transmission electron microscopy (TEM). The density of palladium nuclei on TaN diffusion barrier increases as the grain size of TaN films decreases, which was caused by increasing nitrogen content in TaN films. Plan view TEM results of TiN and TaN diffusiton barriers showed that palladium nuclei formed mainly on the grain boundaries of the diffusion barriers.

Palladium Nanowire Thin Films via Template Growth

2003 ◽  
Vol 775 ◽  
Author(s):  
Donghai Wang ◽  
David T. Johnson ◽  
Byron F. McCaughey ◽  
J. Eric Hampsey ◽  
Jibao He ◽  
...  
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Conductive Substrate ◽  
Palladium Nanowires ◽  
Efficient Route ◽  
Silica Thin Film

AbstractPalladium nanowires have been electrodeposited into mesoporous silica thin film templates. Palladium continually grows and fills silica mesopores starting from a bottom conductive substrate, providing a ready and efficient route to fabricate a macroscopic palladium nanowire thin films for potentially use in fuel cells, electrodes, sensors, and other applications. X-ray diffraction (XRD) and transmission electron microscopy (TEM) indicate it is possible to create different nanowire morphology such as bundles and swirling mesostructure based on the template pore structure.

Nano-Folded Gold Electrocatalysts Enhance the Selectivity of Carbon Dioxide Reduction

2019 ◽  
Author(s):  
Kam Sang Kwok ◽  
Yuxuan Wang ◽  
Michael Cao ◽  
Hao Shen ◽  
Weinan Xu ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Mass Transport ◽  
Gold Film ◽  
X Ray Diffraction ◽  
Thin Gold Film ◽  
Faradaic Efficiency ◽  
X Ray ◽  
Transmission Electron ◽  
Carbon Monoxide Formation ◽  
Catalytic Interfaces

<p>The local structure and geometry of catalytic interfaces can influence the selectivity of chemical reactions. Here, using a pre-strained polymer, we uniaxially compress a thin gold film to form a nano-folded catalyst. We observe two kinds of folds and can tune the ratio of loose to tight folds by varying the extent of pre-strain in the polymer. We characterize the nano-folded catalysts using x-ray diffraction, scanning, and transmission electron microscopy. We observe grain reorientation and coarsening in the nano-folded gold catalysts. Electroreduction of carbon dioxide with these nano-folded catalysts reveals an enhancement of Faradaic efficiency for carbon monoxide formation by a factor of about four. This result suggests that electrolyte mass transport limitations and an increase of the local pH in the tight folds of the catalyst outweigh the effects of alterations in grain characteristics. Together, our studies demonstrate that nano-folded geometries can significantly alter grain characteristics, mass transport, and catalytic selectivity. </p>

Sign in / Sign up

Export Citation Format

Share Document