scholarly journals Study on Application Effect of Sand Consolidating Agent for the Slope of Highway Subgrade in Season Frozen Zone

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
Dongliang Zhang ◽  
Guangqing Yang ◽  
Xiaodi Niu ◽  
Lu Zhang ◽  
Zhijie Wang
Keyword(s):  
Compressive Strength ◽  
Friction Angle ◽  
Freeze Thaw ◽  
Direct Shear Tests ◽  
Thaw Cycle ◽  
Sand Body ◽  
Before And After ◽  
Freeze Thaw Cycle ◽  
Sandy Slope ◽  
Sand Particles

In deep season frozen areas, the solidified layer is easy to be destroyed due to the influence of freeze-thaw cycles after the surface layer of the sandy slope is solidified by chemical methods. In order to study the application effect of the new sand consolidating agent after solidifying sand body, the mechanism of strength formation was analyzed by scanning electron microscopy (SEM). The freeze-thaw cycle tests were carried out on sand consolidating samples. The direct shear tests and unconfined compressive strength tests were carried out before and after freeze-thaw cycles to analyze the freeze-thaw resistance of sand consolidating samples. The sand consolidation agent was tested on-site, and its strength was tested to observe its effect. The results showed that the adhesive membranes on the surface of sand particles were formed by the sand consolidating agent, which increased the cohesion and strength of sand particles. After freeze-thaw cycle tests, the cohesion, internal friction angle, and compressive strength of the solidified sand gradually decreased with increasing freeze-thaw cycles. The decreasing rate reduced from fast to slow and then tends to be stable. The failure mode of samples changed from brittle failure to plastic failure. The sand consolidating layer can effectively prevent collapse of the sandy slope. Combining with the external-soil spray seeding, the sand consolidation layer is beneficial to the growth of plants.

scholarly journals Study on Strength Characteristics of Solidified Contaminated Soil under Freeze-Thaw Cycle Conditions

2018 ◽  
Vol 2018 ◽  
pp. 1-5 ◽  
Author(s):  
Qiang Wang ◽  
Jinyang Cui
Keyword(s):  
Electron Microscopy ◽  
Compressive Strength ◽  
Contaminated Soils ◽  
Unconfined Compressive Strength ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Strength Tests ◽  
Freeze Thaw Cycle ◽  
Microcosmic Mechanism ◽  
Scanning Electron

Cement solidification/stabilization is a commonly used method for the remediation of contaminated soils. The stability characteristics of solidified/stabilized contaminated soils under freeze-thaw cycle are very important. A series of tests, which include unconfined compressive strength tests, freeze-thaw cycle tests, and scanning electron microscopy (SEM) tests, are performed to study the variation law of strength characteristics and microstructure. It aims at revealing the microcosmic mechanism of solidified/stabilized Pb2+ contaminated soils with cement under freeze-thaw cycle. The results show that the unconfined compressive strength of the contaminated soils significantly improved with the increase of the cement content. The unconfined compressive strength of stabilized contaminated soils first increases with the increase of times of freeze-thaw cycle, and after reaching the peak, it decreases with the increase of times of freeze-thaw cycle. The results of the scanning electron microscopy tests are consistent with those of the unconfined compressive strength tests. This paper also reveals the microcosmic mechanism of the changes in engineering of the stabilized contaminated soils under freeze-thaw cycle.

scholarly journals Reliability Analysis of a Direct Shear Test of Modified Iron Tailings Based on the Monte Carlo Algorithm

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Ping Jiang ◽  
Jian Qian ◽  
Na Li
Keyword(s):  
Monte Carlo ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Direct Shear ◽  
Shear Tests ◽  
Type Curve ◽  
Direct Shear Tests ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

The resource utilization of iron tailings is of great significance for all countries in the world. Considering the particle composition and physicochemical characteristics of iron tailings, fiber and lime were used to modify iron tailings. The fiber content was 0%, 0.25%, 0.5%, 0.75%, and 1%, and the lime content was 0%, 2%, 4%, 8%, and 10%, respectively. Through a direct shear test, the shear stress displacement (τ-δ) curves and shear strength of modified iron tailings, under the action of a 0 freeze-thaw cycle and 1 freeze-thaw cycle, were tested. As statistics have shown that there are uncertainty factors associated with direct shear tests, the shear strength index cohesion c and internal friction angle φ of the modified iron tailings were analyzed using the Monte Carlo method. The results show that the τ-δ curve of the fiber-modified iron tailings is a hardening-type curve and that of the lime-modified iron tailings is a softening-type curve. In the direct shear tests, the main uncertain factors are the specimen diameter, vertical force, and horizontal force. The diameter of the sample obeys a normal distribution, and the vertical and horizontal forces obey a uniform distribution. The results of the Monte Carlo simulation show that both c and φ obey a normal distribution. Under a 95% confidence condition, the effect of fiber on the cohesion on iron tailings is obvious, but the effect on the internal friction angle is not obvious. However, the values of c and φ of the iron tailings are clearly improved by lime. Additionally, the iron tailings modified by a fiber content of 1% and those modified by a lime content of 8% have the best frost resistance.

THE INFLUENCE OF FREEZE–THAW CYCLES ON UNCONFINED COMPRESSIVE STRENGTH OF CLAY SOILS TREATED WITH LIME

2015 ◽  
Vol 76 (1) ◽  
Author(s):  
Ali Akbar Firoozi ◽  
Mohd Raihan Taha ◽  
Ali Asghar Firoozi ◽  
Tanveer Ahmed Khan
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Conventional Technique ◽  
Silica Sand ◽  
Clay Soils ◽  
Unit Weight ◽  
Freeze Thaw ◽  
Long Term Stability ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

There are several questions that are not well understood with respect to the long-term stability characteristics of lime-treated clay soils in spite of being used as a conventional technique to improve the properties of clay soils. This paper investigates the influence of freeze-thaw cycles on the unconfined compressive strength of kaolinite and illite mixed with silica sand. The results of this study show that an increase in the number of freeze-thaw cycles decreases the unconfined compressive strength. The role of lime increasing the soil strength is more significant in the case of samples exposed to freeze-thaw cycles compared to those not exposed to freeze-thaw cycles. The effect of freeze-thaw cycles on the dry unit weight and moisture content is insignificant compared to unexposed samples. The maximum volumetric changes occurred in the first freeze-thaw cycle, and afterward, the rate of volume change decreased with an increase in freeze—thaw cycles.

scholarly journals Mechanical Properties and Micro Structure of Cement Concrete in Freeze-Thaw Environment

2021 ◽  
Vol 233 ◽  
pp. 01011
Author(s):  
Xin jian Lv ◽  
Lei Yu ◽  
Ming ming Chai
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Pore Structure ◽  
Fresh Water ◽  
Pore Diameter ◽  
Dynamic Elastic Modulus ◽  
Freeze Thaw ◽  
Salty Water ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

In order to find the declay law of mechanical property and the performance difference after salty water and fresh water freeze-thaw cycle, freeze-thaw cycle environments under the salty water and fresh water are simulated. The compressive strength, dynamic elastic modulus and the mass lost are tested. The pore structure parameters are also tested by MIP. Plot the pore diameter distribution curve. The result shows that the compressive strength and dynamic elastic modulus are all decreased. The degree of these two properties decreasing under salty water freeze and thaw recycle is more than the one under fresh water. The parameters of porosity and critical pore diameter become larger. The amount of pores whose diameter is between 100nm and 1000nm increase. The amount of pores whose diameter is under 100nm decrease. The deteriorate degree of pore structure is deeper in salty water than in fresh water.

scholarly journals Dynamic Mechanical Response and Dissipated Energy Analysis of Sandstone under Freeze-Thaw Cycles

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Ke Man ◽  
Zongxu Liu ◽  
Zhifei Song ◽  
Xiaoli Liu
Keyword(s):  
Compressive Strength ◽  
Strain Rate ◽  
Open Pit ◽  
Dissipated Energy ◽  
Freeze Thaw ◽  
Dynamic Mechanical ◽  
Thaw Cycle ◽  
Pore Evolution ◽  
Freeze Thaw Cycle ◽  
Dynamic Compressive Strength

Based on the sandstone from the slope of Baorixile open-pit mining area in Hulunbuir City, Inner Mongolia, the dynamic uniaxial compression test of sandstone with different freeze-thaw cycles has been carried out by Split Hopkinson Pressure Bar test (SHPB). The test results show that the crushing degree of sandstone becomes serious with the freeze-thaw cycle times and strain rate increases. The dynamic compressive strength increases with the raise of strain rate under the same freeze-thaw cycles, while it reduces with the increases of freeze-thaw cycles at the same strain rate. It is found that the 10 freeze-thaw cycles are an obvious inflection point. When it is less than 10 cycles, the dynamic compressive strength of sandstone specimens decreases rapidly, it is more than 10 cycles, and the strength decreases gradually. This is due to that the evolution progress of pores in sandstone is more uniform after a certain number of freeze-thaw cycles. Meantime, the effect of freezing and thawing is mostly restrained by the pore evolution. On the other hand, the dissipated energy required for sandstone failure grows up with the increase of the number of freeze-thaw cycles. It shows that more energy is needed for the engender of pores and fractures in sandstone caused by freeze-thaw cycle. This led to the deterioration of sandstone structural stability and the decrease of dynamic mechanical properties.

scholarly journals Study on Long-Term Dynamic Mechanical Properties and Degradation Law of Sandstone under Freeze-Thaw Cycle

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Qingsong Pu ◽  
Junhong Huang ◽  
Fuling Zeng ◽  
Yi Luo ◽  
Xinping Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Strain Rate ◽  
Air Pressure ◽  
Freeze Thaw ◽  
Dynamic Mechanical ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
Dynamic Compressive Strength

This study is based on the tunnel-face slope engineering of Dongfeng tunnel in Shanxi section of China’s Shuozhou-Huanghua Railway. The sandstone specimens in the perennial freeze-thaw zone of the slope were collected to carry out freeze-thaw cycle static physical mechanics test and split Hopkinson pressure bar (SHPB) dynamic mechanical test. Thus, the damage process of sandstone under freeze-thaw cycle and impact load is studied. Also, the dynamic compressive strength and dynamic elastic modulus of sandstone are analysed under different loading strain rates and freeze-thaw cycle based on LS-DYNA, a dynamic finite element program. The results showed that the dynamic compressive strength of sandstone subjected to multiple freeze-thaw cycles under 0.04 MPa air pressure has a greater damage ratio than that under 0.055 MPa and 0.07 MPa air pressure, which was more likely to cause damage to slope sandstone than in actual engineering; the dynamic compressive strength and elastic modulus of sandstone decrease greatly within a certain range of freeze-thaw cycles and loading strain rate, leading to significant deterioration. When the freeze-thaw cycle exceeded 200 times and the strain rate was greater than 200 s−1, the physical and mechanical properties of sandstone gradually tended to be stable.

scholarly journals Petrographically Quantifying the Damage to Field and Lab-cast Mortars Subject to Freeze-thaw Cycles and Deicer Applications

2021 ◽  
Author(s):  
CHUNYU QIAO ◽  
Nima Hosseinzadeh Nanehkaran ◽  
Prannoy Suraneni ◽  
Sihang Wei ◽  
David Rothstein
Keyword(s):  
Crack Density ◽  
Cementitious Materials ◽  
X Ray ◽  
Freeze Thaw ◽  
Friedel’S Salt ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
Sand Particles ◽  
Portland Cement Paste ◽  
Scanning Electron

Abstract Although calcium oxychloride (Ca-Oxy) is known to damage cementitious materials exposed to calcium chloride (CaCl2) deicers, there is little direct observation of Ca-Oxy in the field due to its instability. This paper uses optical microscopy (OM) and scanning electron microscopy coupled with energy dispersive X-ray spectrometry (SEM-EDX) to detect the formed Ca-Oxy and quantify its associated damage in a field mortar subject to freeze-thaw cycles and deicer applications. The characterized damage in the field mortar is compared to that in lab-cast portland cement paste and mortar which are submerged in a CaCl2 solution of 25 wt. % under freeze-thaw cycles (-8 to 25 °C). The field and lab-cast mortars show similar cracking patterns that are parallel to the exposure surface with a variation of 30-45° in the preferred orientation due to the constraints of sand particles. During each lab-controlled freeze-thaw cycle, the high CaCl2 concentration of 25 wt. % stabilizes the formed Ca-Oxy, which continually damages the mortar and eventually results in 3-4 times higher crack density compared to that in the field mortar. SEM-EDX analysis confirms the presence of secondary deposits including Friedel’s salt, ettringite and Ca-Oxy. Image analysis on thin section photomicrographs shows a reduction of 86.4% in calcium hydroxide (Ca(OH)2) content in the damaged field mortar compared to the undamaged field mortar, suggesting significant leaching of Ca(OH)2 to form Ca-Oxy due to the deicer application.

THE EFFECT OF PUNCTURING THE ZONA PELLUCIDA ON FREEZE-THAW SURVIVAL OF BOVINE EMBRYOS

1979 ◽  
Vol 59 (3) ◽  
pp. 623-626 ◽  
Author(s):  
H. KANAGAWA ◽  
J. FRIM ◽  
J. KRUUV
Keyword(s):  
Zona Pellucida ◽  
Bovine Embryos ◽  
Freezing And Thawing ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Before And After ◽  
Freeze Thaw Cycle ◽  
Morula Stage ◽  
Glass Knife

The zona pellucida of fertilized bovine embryos of the morula stage (day 6) were punctured using a micromanipulator and a glass knife. In the presence of 2 M DMSO, 23 embryos were cooled (0.5 °C/min) to −196 °C and, upon thawing (10 °C/min), transferred into nine recipients. Although the embryos, before and after the freeze-thaw cycle, were morphologically indistinguishable, only one calf was born. The role of the zona pellucida during freezing and thawing is discussed.

Sign in / Sign up

Export Citation Format

Share Document