scholarly journals Effects of Moisture Content on the Minimum Explosible Concentration of Aluminum Powder and the Related Mechanism

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Haiyan Chen ◽  
Qingguo Yao ◽  
Qiqi Liu ◽  
Hao Liu ◽  
Xinyan Zhang
Keyword(s):  
Moisture Content ◽  
Aluminum Powder ◽  
Combustion Process ◽  
Dilution Effect ◽  
Endothermic Effect ◽  
Aluminum Powders ◽  
Factors Affecting ◽  
Ignition And Combustion ◽  
Explosion Test ◽  
Burn Rate

Aluminum powder has been widely applied to various industries. However, its high activity and high burn rate can cause serious explosion risks. Many factors affecting the explosion of aluminum powder have been determined, yet moisture content has not been included. In the present work, the minimum explosible concentrations of aluminum powders with different moisture contents were measured with a 20-liter explosion test apparatus using the explosion accident in Kunshan, China, as a study case. The experimental results suggest that the minimum explosible concentration of aluminum powder dramatically increases with the increase of its moisture content first and the increasing trend becomes slower as the moisture content further increased. The oxidation time has no significant effects on the minimum explosible concentration of aluminum power in 8 hours at room temperature. Further investigation suggests that the moisture lowers the explosion risk of aluminum powder by altering its surface oxide film, ignition, and combustion process. The low contents of moisture in the range of 0%-8% increase the minimum explosible concentration of aluminum powder by inhibiting the reaction kinetics and particle agglomeration, while high contents of moistures in the range of 8%-20% affect the minimum explosible concentration by the endothermic effect and oxygen dilution effect.

scholarly journals The effects of additives on the combustion characteristics of aluminum powder in steam

RSC Advances ◽  
2017 ◽  
Vol 7 (10) ◽  
pp. 5725-5732 ◽  
Author(s):  
Baozhong Zhu ◽  
Fan Li ◽  
Yunlan Sun ◽  
Qichang Wang ◽  
Yuxin Wu ◽  
...  
Keyword(s):  
Ammonium Perchlorate ◽  
Aluminum Powder ◽  
Combustion Process ◽  
Combustion Characteristics ◽  
Ignition And Combustion ◽  
Different Levels

To develop the combustion characteristics of aluminum powder in steam, the ignition and combustion process of aluminum powder with different additives (KBH4, ammonium perchlorate (AP) and NaCl) addition at different levels were studied using a transparent pipe furnace.

PARAMETER OPTIMIZATION AND EXPERIMENTAL RESEARCH ON THE HAMMER MILL 锤片式粉碎机参数优化与试验研究

2020 ◽  
pp. 341-350
Author(s):  
Di Wang ◽  
Changbin He ◽  
Haiqing Tian ◽  
Liu Fei ◽  
Zhang Tao ◽  
...  
Keyword(s):  
Moisture Content ◽  
Orthogonal Experiment ◽  
Electricity Consumption ◽  
Spindle Speed ◽  
Hammer Mill ◽  
Factors Affecting ◽  
Evaluation Indexes ◽  
Grain Moisture ◽  
Validation Experiment ◽  
Corn Grain

Low productivity and high electricity consumption are considered problems of the hammer mill, which is widely used in current feed production. In this paper, the mechanical properties of corn grain ground by a hammer mill were analysed, and the key factors affecting the performance of the hammer mill were determined. The single-factor experiment and three-factor, three-level quadratic regression orthogonal experiment were carried out with the spindle speed, corn grain moisture content and number of hammers as experimental factors and the productivity and electricity consumption per ton as evaluation indexes. The results showed that the order of influence on the productivity was spindle speed > corn grain moisture content > number of hammers and that the order of influence on the electricity consumption per ton was corn grain moisture content > spindle speed > number of hammers. The parameters were optimized based on the response surface method with the following results: the spindle speed was 4306 r/min, the corn grain moisture content was 10%, and the number of hammers was 24. The validation experiment was carried out with the optimal parameters’ combination. The productivity and electricity consumption per ton were 988.12 kg/h and 5.37 kW·h/t, respectively, which were consistent with the predicted results of the model.

Effect of compost in phytoremediation of diesel-contaminated soils

2001 ◽  
Vol 43 (2) ◽  
pp. 291-295 ◽  
Author(s):  
J. Vouillamoz ◽  
M. W. Milke
Keyword(s):  
Moisture Content ◽  
Contaminated Soil ◽  
Contaminated Soils ◽  
Petroleum Hydrocarbons ◽  
Dilution Effect ◽  
Screening Tests ◽  
Total Petroleum Hydrocarbons ◽  
Controlled Environment ◽  
Grass Growth ◽  
The Impact

The effect of compost on phytoremediation of diesel-contaminated soils was investigated using 130 small (200 g) containers in two screening tests. The experiments were conducted in a controlled environment using ryegrass from seed. Containers were destructively sampled at various times and analyzed for plant mass and total petroleum hydrocarbons. The results indicate that the presence of diesel reduces grass growth, and that compost helps reduced the impact of diesel on grass growth. The addition of compost helps increase diesel loss from the soils both with and without grass, though the addition of grass leads to lower diesel levels compared with controls. A second set of experiments indicates that the compost helps in phytoremediation of diesel-contaminated soil independent of the dilution effect that compost addition has. The results indicate that the compost addition allowed diesel loss down to 200 mg TPH/kg even though the compost would be expected to hold the diesel more tightly in the soil/compost mixture. The simplicity of the screening tests led to difficulties in controlling moisture content and germination rates. The conclusion of the research is that the tilling of compost into soils combined with grass seeding appears to be a valuable option for treating petroleum-contaminated soils.

Numerical Simulation on Moisture Influence to MSW Combustion

2014 ◽  
Vol 1006-1007 ◽  
pp. 181-184
Author(s):  
Zhu Sen Yang ◽  
Xing Hua Liu ◽  
Shu Chen
Keyword(s):  
Numerical Simulation ◽  
Moisture Content ◽  
Flue Gas ◽  
Combustion Process ◽  
Average Temperature ◽  
Excess Air ◽  
Heat Value ◽  
Moisture Influence ◽  
Excess Air Coefficient ◽  
Combustible Gases

The combustion process of municipal solid waste (MSW) in a operating 750t/d grate furnace in Guangzhou was researched by means of numerical simulation. The influence of MSW moisture content on burning effect was discussed. The results show that: with the moisture content dropped from 50% to 30%, the heat value could be evaluated from 13.72% to 54.91% and the average temperature in the furnace could be promoted 90-248°C. However, the combustible gases and particle in the flue gas of outlet would take up a high proportion since lacking of oxygen would lead to an incomplete combustion. The excess air coefficient should be increased to 2.043~2.593 in order to ensure the flue gas residence time more than 2s and temperature in the furnace higher to 800°C.

Analysis of environmental factors affecting methane production from high-solids organic waste

1997 ◽  
Vol 36 (6-7) ◽  
pp. 493-500 ◽  
Author(s):  
J. J. Lay ◽  
Y. Y. Li ◽  
T. Noike ◽  
J. Endo ◽  
S. Ishimoto
Keyword(s):  
Moisture Content ◽  
Methane Production ◽  
Organic Waste ◽  
High Solids ◽  
Methanogenic Activity ◽  
Factors Affecting ◽  
Bacterial System ◽  
Sludge Cake ◽  
Production Curve ◽  
Ph Range

A simple model developed from the Gompertz equation was used to describe the cumulative methane production curve in the batch culture. By using this model, three key parameters, namely methane production rate, potential and lagphase time, in a cumulative methane production curve were exactly estimated based on the experimental data. The results indicate that each gram of dry organic waste of a sludge cake, meat, carrot, rice, potato and cabbage had a methane production potential of 450, 424, 269, 214, 203 and 96 mL, respectively. The methanogenic activity of these digesters decreased with a decrease in the moisture content. The moisture content threshold limit, at which the methanogenic activity dropped to zero, was found to be 56.6% for the sludge cake, but greater than 80% for meat, carrot and cabbage. In the high-solids sludge digestion, the relative methanogenic activity dropped from 100% to 53% when the moisture content decreased from 96% to 90%. The rate of methane production at moisture contents of 90% to 96% functioned in a pH range between 6.6 and 7.8, but optimally at pH 6.8, and the process may fail if the pH was lower than 6.1 or higher than 8.3. On the other hand, the methanogenic activity was dependent on the level of ammonium, NH4+, but not free ammonia, NH3, indicating that the NH4+ was the more significant factor rather than the NH3 in affecting the methanogenic activity of a well-acclimatized bacterial system. In the wide pH range of 6.5 to 8.5, the methanogenic activity decreased with the increase in the NH4+; dropped 10% at the NH4+-N concentration of 1670-3720 mg·L−1, 50% at 4090-5550 mg·L−1 and dropped to zero at 5880-6600 mg·L−1. However, the lagphase time was dependent on the NH3 level, but not on NH4+, and when NH3-N was higher than 500 mg·L−1, a notable shock was observed. This suggests that the NH3 level was the more sensitive factor than the NH4+ level for an unacclimatized bacterial system.

scholarly journals Characteristics of Woody Cutting Waste Briquette with Paper Waste Pulp as Binder

2020 ◽  
Vol 190 ◽  
pp. 00030
Author(s):  
Qurrotin Ayunina Maulida Okta Arifianti ◽  
Azmi Alvian Gabriel ◽  
Syarif Hidayatulloh ◽  
Kuntum Khoiro Ummatin
Keyword(s):  
Moisture Content ◽  
Ignition Time ◽  
Combustion Process ◽  
Calorific Value ◽  
Volatile Matter ◽  
Proximate Analysis ◽  
Hydraulic Press ◽  
Combustion Characteristic ◽  
Paper Waste ◽  
Iron Mold

The current research aimed to increase the calorific value of woody cutting waste briquette with paper waste pulp as binder. There were three different binder variation used in this study, they are 5 %, 10 %, and 15 %. To create a briquette, a cylindrical iron mold with diameter of 3.5 cm and height of 3 cm and a hydraulic press with 2 t power were applied. The physical characteristics of the combination woody waste briquette and paper waste pulp, such as moisture content, ash content, volatile matter and carbon fix were examined using proximate analysis. The calorific value of briquetted fuel was tested by bomb calorimeter. The combustion test was performed to determine the combustion characteristic of briquettes, for example initial ignition time, temperature distribution, and combustion process duration. The general result shows that the calorific value of briquette stood in the range of 4 876 kCal kg–1 to 4 993 kCal kg–1. The maximum moisture content of briquette was 5.32 %. The longest burning time was 105 min.

scholarly journals Study on the Microscopic Mechanism of Spontaneous Combustion and Oxidation Kinetics of Water-Leached Coal

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Naifu Cao ◽  
Gang Wang ◽  
Yuntao Liang
Keyword(s):  
Kinetic Model ◽  
Moisture Content ◽  
Spontaneous Combustion ◽  
Water Immersion ◽  
Combustion Process ◽  
Oxidation Kinetic ◽  
Oxidation Mechanism ◽  
Temperature Oxidation ◽  
Before And After ◽  
Spontaneous Combustion Of Coal

In this article, a series of experiments have been carried out to study the spontaneous combustion and oxidation mechanism of coal after water immersion and investigate its tendency to spontaneous combustion, analyze the difficulty of spontaneous combustion of coal samples under different water immersion conditions, and establish a kinetic model of water immersion coal oxidation (taking the Bulianta 12# coal as a case study). They rely on physical oxidation adsorption, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetry, and oil bath heating. SEM has been used to analyze the characteristics of coal pore structure under different water immersion conditions (water-saturated coal samples under different water loss conditions until the coal samples are completely dried); FTIR served to investigate the characteristics of the molecular chemical structure of the coal surface before and after the coal is immersed in water. Through programmed temperature oxidation experiments combined with FTIR analyses and gas chromatographic (GC) analysis of gaseous products, it has been possible to study the changes of molecular structure and gas products on the surface of coal samples at different temperatures and water immersion conditions. The oxidation reaction rate of the 12# coal samples of Shendong Mine’s Bulianta Mine under different water content conditions during the spontaneous combustion process has been quantitatively studied. The difficulty of spontaneous combustion of coal samples has been correspondingly addressed. A kinetic model from the perspective of oxygen consumption has been proposed. Thermogravimetry-differential scanning calorimetry (TG-DSC) has been used to analyze and study the exothermal oxidation process before and after coal immersion. From the perspective of the exothermic intensity of the coal-oxygen reaction, an oxidation kinetic model for immersed coal samples has been developed to qualitatively determine its spontaneous combustion tendency. Results have shown that the increase in the specific surface area increases the risk of spontaneous combustion, and coal samples after soaking and drying have a stronger tendency to spontaneous combustion than raw coal. The moisture content of the coal sample leading to the easiest ignition conditions is 16.05%. Regardless of the moisture content, the critical temperature is maintained at 65–75°C, and the temperature of the left coal in the goaf should be prevented from exceeding this critical value.

Synthesis of Aluminum Nitride Whiskers Via a Vapor-Liquid-Solid Process

1998 ◽  
Vol 547 ◽  
Author(s):  
Ying Dai ◽  
Ce-Wen Nan
Keyword(s):  
Carbon Black ◽  
Aluminum Nitride ◽  
Aluminum Powder ◽  
Nitrogen Atmosphere ◽  
Processing Conditions ◽  
Vapor Liquid Solid ◽  
Aluminum Powders ◽  
Sem And Tem ◽  
Vapor Liquid Solid Mechanism ◽  
Vapor Liquid

AbstractAluminum nitride whiskers were synthesized by nitridation of commercial aluminum powder at 1623K in a nitrogen atmosphere. The starting materials consisted of aluminum and carbon black. The carbon acted as a barrier between aluminum powders during nitridation and was removed by heating in air at 923K. The whiskers were about 0.5-1μm in diameter and 10-20μm in length. The droplets at the whisker tips showed that the whiskers grew via a vapor-liquid-solid mechanism. The morphologies of the whiskers were studied by means of SEM and TEM. The formation of the whiskers depended on the processing conditions.

Sign in / Sign up

Export Citation Format

Share Document