scholarly journals Seismic Performance of Steel Box Bridge Piers with Earthquake-Resilient Function

2020 ◽  
Vol 2020 ◽  
pp. 1-24
Author(s):  
Haifeng Li ◽  
Wenwei Luo ◽  
Jun Luo
Keyword(s):  
Energy Dissipation ◽  
Bearing Capacity ◽  
Seismic Performance ◽  
Seismic Behavior ◽  
Bridge Pier ◽  
Steel Bridge ◽  
Deformation Capacity ◽  
The Novel ◽  
Seismic Capacity ◽  
Energy Dissipated

A novel steel box bridge pier with replaceable energy dissipation wall plates at the base was proposed. After moderate earthquakes, the damaged energy dissipation wall plates and constraining steel plates on the two sides could be rapidly replaced, while the entire energy-dissipated column at the base can also be replaced after rare earthquakes. In this way, the seismic capacity of the new type of steel box bridge pier could be restored after earthquakes. For the purpose of discussing the seismic performance of this novel steel box-shaped bridge pier, the pseudostatic test and numerical simulation were performed. The results showed that the failure of the specimens in the pseudostatic tests occurred predominantly in the energy dissipation zone at the base. After replacing the damaged energy-dissipated column at the base, the seismic behavior of the proposed steel bridge pier can be recovered rapidly. Axial compression ratio is an important factor influencing the seismic behavior of the novel steel box bridge pier. The strength of the energy dissipation wall plates influences the novel steel box-shaped bridge pier’s bearing capacity and deformation capacity. Spacing between the horizontal stiffening ribs had little impact on the bearing capacity and deformation capacity of the proposed steel bridge pier. The larger the thickness of the energy dissipation wall plate, the higher the bearing capacity and deformation capacity of the steel box bridge pier. Finally, an empirical equation for the design of this novel steel bridge pier under cyclic loading was proposed.

Experimental study on seismic performance of suspended ceiling components

2021 ◽  
Author(s):  
Yong Wang ◽  
Huanjun Jiang ◽  
Chen Wu ◽  
Zihui Xu ◽  
Zhiyuan Qin
Keyword(s):  
Experimental Study ◽  
Energy Dissipation ◽  
Seismic Performance ◽  
Seismic Vulnerability ◽  
Axial Loading ◽  
Deformation Capacity ◽  
Severe Damage ◽  
Strong Earthquakes ◽  
Static Tests ◽  
Load Carrying

<p>Suspended ceiling systems (SCSs) experienced severe damage during strong earthquakes that occurred in recent years. The capacity of the ceiling component is a crucial factor affecting the seismic performance of SCS. Therefore, a series of static tests on suspended ceiling components under monotonic and cyclic loadings were carried out to investigate the seismic performance of the ceiling components. The ceiling components include main tee splices, cross tee latches and peripheral attachments. All specimens were tested under axial loading. Additionally, the static tests of cross tee latches subjected to shear and bending loadings were performed due to their seismic vulnerability. The failure pattern, load-carrying ability, deformation capacity and energy dissipation of the ceiling components are presented in detail in this study.</p>

Experimental and numerical investigation on seismic performance of hollow floor interior slab-column connections

2020 ◽  
pp. 136943322096527
Author(s):  
Longji Dang ◽  
Rui Pang ◽  
Rui Liu ◽  
Hongmei Ni ◽  
Shuting Liang
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Seismic Performance ◽  
Seismic Behavior ◽  
Element Model ◽  
Experimental Results ◽  
Element Analysis ◽  
Skeleton Curve ◽  
The North ◽  
Parallel Tube

This paper aims to investigate the seismic performance of hollow floor interior slab-column connection (HFISC). In this new connection system, several tube fillers are placed in slab to form hollow concrete. Moreover, locally solid zone, shear components, and hidden beam around the connections are installed to improve the bearing capacity and ductility of specimens. Three slab-column connections with different shear components were tested under cyclic loading and every specimen was constructed with parallel tube fillers in the north direction and orthogonal tube fillers in the south direction. The seismic behavior of specimens was evaluated according to the hysteretic response, skeleton curve, ductility, stiffness degradation, and energy dissipation. A finite element model was then developed and validated by a comparison with the experimental results. Based on experimental results and finite element analysis results, the relative effects of the hollow ratio of slab, the ratio of longitudinal reinforcement, the shear area of bent-up steel bars, and the arm length of welding section steel cross bridging were elucidated through parametric studies. This new slab-column connection showed better plastic deformation capacity while the bearing capacity was kept. Specimens with parallel tube fillers showed better seismic behavior than those of specimens with orthogonal tube fillers.

Experimental Study on Seismic Performance of the Reinforced Concrete Grid-Mesh Frame Wall

2013 ◽  
Vol 680 ◽  
pp. 234-238
Author(s):  
Jin Li Qiao ◽  
Wen Ling Tian ◽  
Ming Jie Zhou ◽  
Fang Lu Jiang ◽  
Kun Zhao
Keyword(s):  
Experimental Study ◽  
Reinforced Concrete ◽  
Energy Dissipation ◽  
Bearing Capacity ◽  
Seismic Performance ◽  
Seismic Energy ◽  
Width Ratio ◽  
Filling Material ◽  
Energy Dissipation Capacity ◽  
Grid Mesh

In order to validate the seismic performance of reinforced concrete grid-mesh frame wall , four grid frame walls in half size is made with different height-width ratios and different grid forms in the paper. Two of them are filling with cast-in-place plaster as filling material. According to the experimental results of these four walls subjected to horizontal reciprocating loads, we know that the grid-mesh frame wall's breaking form are in stages and multiple modes, and the main influencing factors are height-width ratio and grid form, what's more, with cast-in-place plaster as fill material, could not only improve the level of the wall bearing capacity and stiffness, but also improve the ductility and seismic energy dissipation capacity.

scholarly journals Seismic Performance of Masonry Walls Built with New Type of Fired Shale Hollow Blocks

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Jian Wu ◽  
Liangcheng Zeng ◽  
Bo Wang
Keyword(s):  
Energy Dissipation ◽  
Aspect Ratio ◽  
Bearing Capacity ◽  
Compressive Stress ◽  
Seismic Performance ◽  
Stiffness Degradation ◽  
Masonry Walls ◽  
Secant Stiffness ◽  
Hollow Block ◽  
New Type

This paper presents the cyclic loading test results of a new type of fired shale hollow block masonry walls. Six specimens were designed including two specimens without reinforcements (bare walls) and four specimens constrained by structural columns (reinforced walls). The influences of aspect ratio, vertical compressive stress, and structural column on the seismic performance of the specimens were investigated. The failure mode, bearing capacity, ductility, stiffness degradation, and energy dissipation of specimens were analyzed. The results showed that the crack patterns of specimens changed from the horizontal straight shape (bare walls) to “X” shape (reinforced walls), and the corresponding bearing capacity, ductility, stiffness degradation, and energy dissipation of the specimens were improved. With the increase of the vertical compressive stress, the ductility and the secant stiffness of the specimens increased. Moreover, with the decrease of aspect ratio, the bearing capacity and secant stiffness of the masonry walls increased, while the energy dissipation capacity decreased. This paper confirms that fired shale hollow block walls could meet the seismic requirements through appropriate design, which could promote the application of this new type of block in civil engineering.

Experimental Investigations on the Seismic Behavior of Precast Concrete Columns with Novel Box Connections

2019 ◽  
Vol 14 (02) ◽  
pp. 2050007
Author(s):  
Xizhi Zhang ◽  
Shengbo Xu ◽  
Shaohua Zhang ◽  
Gaodong Xu
Keyword(s):  
Energy Dissipation ◽  
Bearing Capacity ◽  
Failure Mode ◽  
Seismic Behavior ◽  
Load Transfer ◽  
Precast Concrete ◽  
Hysteretic Behavior ◽  
Experimental Investigations ◽  
Test Results ◽  
Energy Dissipation Capacity

In this study, two types of novel box connections were developed to connect precast concrete (PC) columns and to ensure load transfer integrity. Cyclic loading tests were conducted to investigate the seismic behavior of the PC columns with proposed connections as well as the feasibility and reliability of novel box connections. The failure mode, hysteretic behavior, bearing capacity, ductility, stiffness degradation and energy dissipation were obtained and discussed. The test results indicated that the all PC columns exhibited the ductile flexural failure mode and that the proposed connections could transfer the force effectively. The adoption of novel box connections could improve the deformation capacity and energy dissipation capacity of PC columns. A higher axial compression ratio could enhance the bearing capacity of PC column with proposed connection but would significantly deteriorate the ductility and energy dissipation capacity. Finite element models were developed and the feasibility of the models was verified by the comparison with the test results.

scholarly journals Experimental Analysis of Seismic Performance of Masonry Shear Wall Reinforced with PP-Band Mesh and Plastering Mortar under In-Plane Cyclic Loading

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Qiang Zhou ◽  
Lingyu Yang ◽  
Wenyang Zhao
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Bearing Capacity ◽  
Low Cost ◽  
Low Frequency ◽  
Masonry Wall ◽  
Ultimate Bearing Capacity ◽  
Masonry Walls ◽  
Seismic Capacity ◽  
Energy Dissipation Capacity

Masonry structures are widely used in developing countries due to their low cost and simple construction, especially in remote areas, where there are a large number of houses without seismic measures. These buildings are prone to collapse and cause a lot of casualties, even under the action of small earthquakes. For the reinforcement of this structure, a cheap, effective, and easy-to-construct reinforcement method is urgently needed. Therefore, this article studies the reinforcement method of polypropylene bands (PP-bands). We have carried out low-frequency cyclic loading tests for two PP-band reinforced masonry walls and two compared masonry walls. We mainly studied the influence of PP-band and different compressive strengths of plastering mortar on the masonry wall’s seismic capacity. The seismic indicators mainly studied in this article include ultimate bearing capacity, energy dissipation capacity, stiffness degradation, and hysteresis characteristics. The experimental results show that the PP-band can greatly enhance the seismic capacity of the masonry wall. The ultimate bearing capacity, energy dissipation capacity, and displacement ductility of the PP-band reinforced wall are increased by 38%–48%, 22%–47%, and 138%–226%.

Seismic Performance of Haunched Beam Transfer Structures of Frame-Supported Short-Leg Shearwall with Varied Ratio of Short-Leg Shearwall Section Height to Thickness

2011 ◽  
Vol 255-260 ◽  
pp. 2308-2312
Author(s):  
Yong Qi ◽  
Ci Mian Zhu ◽  
Shu Sheng Zhong ◽  
Fang Wang ◽  
Yang Xiang
Keyword(s):  
Experimental Study ◽  
Energy Dissipation ◽  
Seismic Performance ◽  
Seismic Behavior ◽  
Low Frequency ◽  
Beam Structure ◽  
Beam Structures ◽  
Cyclic Lateral Load ◽  
Energy Dissipation Capacity ◽  
Seismic Tests

This paper deals with an experimental study on the seismic performance of haunched transfer beam structures with varied ratio of section height to thickness of short-leg shearwall (RHT). Based on the seismic tests of three 1:3-scaled specimens under low-frequency cyclic lateral load with constant vertical actions, the failure pattern, the hysteresis curves, the skeleton curves, the energy dissipation capacity, and the stiffness degradation laws of haunched transfer beam structures are investigated. The effects of different RHT (i.e., 5, 6 and 7) on the seismic performance of haunched transfer beam structures are emphasized and analyzed in detail. It is concluded that the rigidity of the structure is noticeable enhanced, the endogen force becomes more evenly distributed and the bearing is more rational with an increase of the RHT; the rationally designed haunched transfer beam structure has a good seismic behavior.

Experimental Research on Seismic Behavior of Interior Joints of Specially Shaped Columns Reinforced by Fiber

2011 ◽  
Vol 94-96 ◽  
pp. 551-555 ◽  
Author(s):  
Xian Rong ◽  
Jian Xin Zhang ◽  
Yan Yan Li
Keyword(s):  
Energy Dissipation ◽  
Bearing Capacity ◽  
Seismic Behavior ◽  
Steel Fiber ◽  
Polypropylene Fiber ◽  
The Core ◽  
Low Cyclic Loading ◽  
The Moment ◽  
Specially Shaped Column ◽  
Damage Characteristic

Based on the low cyclic loading experiments on three interior joints with specially shaped columns, in which one of them was reinforced by polypropylene fiber in the core zone of joint, another steel fiber, the other was not reinforced, the authors compare the results in terms of damage characteristic, bearing capacity, displacement and ductility, hysteretic curve of the moment-rotation, rigidity degradation and energy dissipation. It is shown that seismic behavior of specially shaped column interior joints reinforced by fiber is improved significantly. The interior joint of specially shaped column reinforced by polypropylene fiber has a better damage characteristic and energy dissipation while that by steel fiber shows a higher yield load and bearing capacity.

scholarly journals On the Seismic Performance of Autoclaved Aerated Concrete Self-Insulation Block Walls

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2942
Author(s):  
Yun Liu ◽  
Gonglian Chen ◽  
Zhipeng Wang ◽  
Zhen Chen ◽  
Yujia Gao ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
Bearing Capacity ◽  
Seismic Performance ◽  
Shear Capacity ◽  
Seismic Load ◽  
Masonry Walls ◽  
Autoclaved Aerated Concrete ◽  
Aerated Concrete ◽  
Energy Dissipation Capacity ◽  
Insulation Block

Autoclaved aerated concrete (AAC) self-insulation block masonry is often used for the infill walls in steel and concrete frame structures. To work together with the frame under earthquake action, it is essential to understand the seismic behavior of AAC self-insulation block masonry walls. In this paper, six AAC self-insulation block masonry walls were experimentally studied under the pseudo static test. The load-displacement hysteretic curves were drawn with the test data. The failure characteristics, loading capacity, stiffness degeneration, energy dissipation capacity and hysteretic behavior are analyzed. The results indicate that the blocks underwent internal failure due to the lower strength with a larger size, but the walls had good energy dissipation capacity with a rational bearing capacity. Accompanied by the influence of vertical compressive stress on the top surface of the walls, the cracking resistance, ultimate bearing capacity, deformability and energy dissipation capacity of the walls were affected by the masonry mortar joints. Comparatively, the walls with thin-layer mortar joints had better seismic performance than those with insulation mortar joints or with vertical joints filled by mineral wool plates. Finally, the shear capacity of the walls under seismic load is evaluated referring to the formulas of current design codes for masonry walls.

Seismic Performance of SFRC Piers under Reversed Cyclic Loading

2012 ◽  
Vol 178-181 ◽  
pp. 2228-2235 ◽  
Author(s):  
Yu Ye Zhang ◽  
Hong Yi Wei ◽  
Wan Cheng Yuan ◽  
Wei Hu
Keyword(s):  
Energy Dissipation ◽  
Bearing Capacity ◽  
Seismic Behavior ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Plastic Hinge ◽  
Content Volume ◽  
Fiber Reinforced Concrete ◽  
Steel Fiber Reinforced Concrete ◽  
Fiber Volume

Steel fiber reinforced concrete (SFRC) has many good dynamic performances such as toughness and ductility. However, few studies have focused on SFRC’s application in bearing member of bridge structures. In this paper, pseudo-static cyclic tests of eight pier specimens are carried out to investigate seismic behavior of piers using SFRC. The main variables in the testing are the steel fiber content (volume fraction of 0.0%, 0.5%, 1.0% and 1.5%), the length of SFRC region and the stirrup ratio of piers. Seismic behavior of the test specimens, like the failure pattern, the hysteretic characteristics, the skeleton curves, the ductility and the energy dissipation are investigated experimentally. The results show that, 1) the SFRC pier with the steel fiber volume fraction of 1.0% has much better performance than that with other fiber volume contents, particularly for bearing capacity, hysteretic energy dissipation and ductility; 2) the pier specimen can keep sufficient seismic capacity, in which some stirrups are replaced by steel fibers; and 3) compared with specimen with application of SFRC in entire pier, the specimen with appropriate local application of SFRC in potential plastic hinge region can sustain almost the same seismic properties, such as the ultimate bearing capacity, the stiffness, the ductility and the energy dissipation capacity.

Sign in / Sign up

Export Citation Format

Share Document