scholarly journals Design of an S-Band Phased Array with Modified Dipoles

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Meng Xiang ◽  
Yu Xiao ◽  
Bin Xi ◽  
Yue Zhang ◽  
Shiyou Xu
Keyword(s):  
Antenna Array ◽  
Impedance Matching ◽  
Equivalent Circuit Model ◽  
High Gain ◽  
Wide Angle ◽  
Cross Polarization ◽  
Matching Layer ◽  
Unit Cells ◽  
Operating Bandwidth ◽  
Polarization Level

A wideband, low cross-polarization, high-gain, and wide-angle scanning antenna array is presented in this paper. The antenna array contains 8 subarrays in the horizontal dimension, and each subarray contains 4 unit cells. A two-side printed dipole with an amendatory equivalent circuit model is adopted, and the metal vias are introduced in the element design to ameliorate the cross-polarization level. A radome, acting as the wide-angle impedance matching layer, is introduced to achieve wide-angle scanning. A prototype of a 4 × 8 array is fabricated and measured. The results show that the operating bandwidth of aperture efficiency (BWAE) above 60% is about 26.7% from 2.6 GHz to 3.4 GHz. The measured scanning loss in the H-plane is 2.7 dB when scanning up to 60° with active voltage standing wave ratio (VSWR) <3, and the gain can achieve 21 dB at 3 GHz with a cross-polarization level below −30 dB at all angles.

scholarly journals A 300-GHz low-cost high-gain fully metallic Fabry–Perot cavity antenna for 6G terahertz wireless communications

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Basem Aqlan ◽  
Mohamed Himdi ◽  
Hamsakutty Vettikalladi ◽  
Laurent Le-Coq
Keyword(s):  
Communication Systems ◽  
Low Cost ◽  
Frequency Selective Surface ◽  
High Gain ◽  
Wireless Communication Systems ◽  
Beam Radiation ◽  
Compact Size ◽  
Fabry Perot ◽  
Operating Bandwidth ◽  
Polarization Level

AbstractA low-cost, compact, and high gain Fabry–Perot cavity (FPC) antenna which operates at 300 GHz is presented. The antenna is fabricated using laser-cutting brass technology. The proposed antenna consists of seven metallic layers; a ground layer, an integrated stepped horn element (three-layers), a coupling layer, a cavity layer, and an aperture-frequency selective surface (FSS) layer. The proposed aperture-FSS function acts as a partially reflective surface, contributing to a directive beam radiation. For verification, the proposed sub-terahertz (THz) FPC antenna prototype was developed, fabricated, and measured. The proposed antenna has a measured reflection coefficient below − 10 dB from 282 to 304 GHz with a bandwidth of 22 GHz. The maximum measured gain observed is 17.7 dBi at 289 GHz, and the gain is higher than 14.4 dBi from 285 to 310 GHz. The measured radiation pattern shows a highly directive pattern with a cross-polarization level below − 25 dB over the whole band in all cut planes, which confirms with the simulation results. The proposed antenna has a compact size, low fabrication cost, high gain, and wide operating bandwidth. The total height of the antenna is 1.24 $${\lambda }_{0}$$ λ 0 ($${\lambda }_{0}$$ λ 0 at the design frequency, 300 GHz) , with a size of 2.6 mm × 2.6 mm. The proposed sub-THz waveguide-fed FPC antenna is suitable for 6G wireless communication systems.

Reduced Cross-Polarization Patch Antenna with Optimized Impedance Matching Using a Complimentary Split Ring Resonator and Slots as Defected Ground Structure

2021 ◽  
Vol 36 (6) ◽  
pp. 718-725
Author(s):  
Narayanasamy RajeshKumar ◽  
Palani Sathya ◽  
Sharul Rahim ◽  
Akaa Eteng
Keyword(s):  
Patch Antenna ◽  
Ring Resonator ◽  
Impedance Matching ◽  
Equivalent Circuit Model ◽  
Split Ring Resonator ◽  
Cross Polarization ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Split Ring ◽  
Surface Current Density

An innovative method is proposed to improve the cross-polarization performance and impedance matching of a microstrip antenna by integrating a complimentary split ring resonator and slots as a defected ground structure. An equivalent circuit model (ECM) enables the design take into consideration the mutual coupling between the antenna patch and the Defected Ground Structure. The input impedance and surface current density analysis confirms that the integration of a CSRR within a rectangular microstrip patch antenna leads to uniform comparative cross-polarization level below 40 dB in the H-plane, over an angular range of ± 50°. Introducing parallel slots, as well, leads to a reduction of spurious antenna radiation, thereby improving the impedance matching. Measurements conducted on a fabricated prototype are consistent with simulation results. The proposed antenna has a peak gain of 4.16 dB at 2.6 GHz resonating frequency, and hence is good candidate for broadband service applications.

scholarly journals A High-Isolation Dual-Polarization Substrate-Integrated Fabry-Pérot Cavity Antenna

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Chang Chen ◽  
Bo-Liang Liu ◽  
Ling Ji ◽  
Wei-Dong Chen
Keyword(s):  
Near Field ◽  
Ground Plane ◽  
Cross Polarization ◽  
Dual Polarization ◽  
High Isolation ◽  
Fabry Perot ◽  
Feeding Structure ◽  
Operating Bandwidth ◽  
High Degree ◽  
Polarization Level

A dual-polarization substrate-integrated Fabry-Pérot cavity (SI-FPC) antenna is presented in this paper. The patch embedded in SI-FPC is excited with a near-field coupled feeding structure for V-polarization and with a slot-coupled feeding structure for H-polarization. The feeding structures are separated by a ground plane to improve the isolation between the ports. As a design example, an antenna operating at 10.0 GHz is fabricated and measured. A high degree of port isolation (<−40 dB) over the whole operating bandwidth (9.5–10.2 GHz) and good cross-polarization level (>25 dB) can be achieved.

scholarly journals A Wideband Rectenna Using High Gain Fractal Planar Monopole Antenna Array for RF Energy Scavenging

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Mohammad M. Fakharian
Keyword(s):  
Antenna Array ◽  
Conversion Efficiency ◽  
Power Level ◽  
Impedance Matching ◽  
High Gain ◽  
Input Power ◽  
Monopole Antenna ◽  
Energy Scavenging ◽  
Wireless Power ◽  
Circuit Performance

This paper introduces a wideband rectenna that can scavenge ambient wireless power to a range of frequency band from 0.91 GHz to 2.55 GHz efficiently. The proposed rectenna is based on a wideband 2 × 2 fractal monopole antenna array with omnidirectional radiation patterns and high gains of 5 to 8.3 dBi at the desired bands. An improved two-branch impedance matching technique is presented which is designed to enhance the rectifier circuit performance with a relatively low input power ranging from −25 dBm to 10 dBm. Also, a full-wave wideband rectifier that can suitably improve the RF-to-DC power conversion efficiency is designed for the rectenna. A peak efficiency of 76%, 71%, 61%, and 62% is obtained at 950, 1850, 2100, and 2450 MHz, respectively. Measurement results show that a conversion efficiency of 68% has been achieved over an optimal 4.7 kΩ resistor when the simultaneous four-band input power level is −10 dBm. Moreover, an output DC voltage of around 243 mV with voltage varying within 160–250 mV can be achieved by gathering the low ambient wireless power inside laboratory. This study proves that the proposed rectenna can be applied to a range of many low-power electronic applications.

scholarly journals A Planar Ultrawideband Patch Antenna Array for Microwave Breast Tumor Detection

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4918
Author(s):  
Amran Hossain ◽  
Mohammad Tariqul Islam ◽  
Md. Tarikul Islam ◽  
Muhammad E. H. Chowdhury ◽  
Hatem Rmili ◽  
...  
Keyword(s):  
Antenna Array ◽  
Breast Imaging ◽  
Impedance Matching ◽  
Uwb Antenna ◽  
Minor Variation ◽  
Face To Face ◽  
Breast Phantom ◽  
Operating Bandwidth ◽  
Imaging Performance ◽  
Compact Planar

In this paper, a compact planar ultrawideband (UWB) antenna and an antenna array setup for microwave breast imaging are presented. The proposed antenna is constructed with a slotted semicircular-shaped patch and partial trapezoidal ground. It is compact in dimension: 0.30λ × 0.31λ × 0.011λ, where λ is the wavelength of the lowest operating frequency. For design purposes, several parameters are assumed and optimized to achieve better performance. The prototype is applied in the breast imaging scheme over the UWB frequency range 3.10–10.60 GHz. However, the antenna achieves an operating bandwidth of 8.70 GHz (2.30–11.00 GHz) for the reflection coefficient under–10 dB with decent impedance matching, 5.80 dBi of maximum gain with steady radiation pattern. The antenna provides a fidelity factor (FF) of 82% and 81% for face-to-face and side-by-side setups, respectively, which specifies the directionality and minor variation of the received pulses. The antenna is fabricated and measured to evaluate the antenna characteristics. A 16-antenna array-based configuration is considered to measure the backscattering signal of the breast phantom where one antenna acts as transmitter, and 15 of them receive the scattered signals. The data is taken in both the configuration of the phantom with and without the tumor inside. Later, the Iteratively Corrected Delay and Sum (IC–DAS) image reconstructed algorithm was used to identify the tumor in the breast phantom. Finally, the reconstructed images from the analysis and processing of the backscattering signal by the algorithm are illustrated to verify the imaging performance.

scholarly journals Circularly polarized antenna array based on hybrid couplers for 5G devices

2021 ◽  
Vol 10 (3) ◽  
Author(s):  
Tan Minh Cao ◽  
Thao Hoang Thi Phuong ◽  
Thi Duyen Bui
Keyword(s):  
Antenna Array ◽  
High Efficiency ◽  
3D Structure ◽  
High Gain ◽  
Operating Frequency ◽  
Antenna Gain ◽  
Suitable Candidate ◽  
Circularly Polarized ◽  
Operating Bandwidth ◽  
Peak Gain

This paper depicts a wideband circularly polarized (CP) antenna for 5G devices. The antenna array has a 3D structure including four simple printed dipole elements with directional radiations, high gain, and high efficiency. It achieves a CP by using the sequential rotation (SR) feeding based on 90°-3dB hybrid couplers in the proposed feeding network. The antenna array bandwidth is wide, 26.7%, with an operating frequency band from 3.35 GHz to 4.35 GHz. The antenna achieves a high peak gain of 10.73 dBi and high efficiency of 93.75%. Besides, the antenna gain is stable over the operating bandwidth (BW). At the centre operating frequency of 3.75 GHz, the angle of circular polarization is 51°. The antenna is designed and fabricated on the Rogers 4003 C substrate. The measured S11 is well matching with the simulation results. With the above characteristics, the proposed antenna can be a suitable candidate for 5G devices.

Sign in / Sign up

Export Citation Format

Share Document