scholarly journals Effects of Ship Propulsion Shafting Alignment on Whirling Vibration and Bearing Temperature Response

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Junsong Lei ◽  
Ruiping Zhou ◽  
Hao Chen ◽  
Guobing Huang ◽  
Yakun Gao ◽  
...  
Keyword(s):  
High Speed ◽  
Vertical Component ◽  
Temperature Response ◽  
Stable Operation ◽  
Test Scheme ◽  
Centre Line ◽  
Bearing Load ◽  
The Relationship ◽  
Dynamic Alignment ◽  
Ship Vibration

Ship’s propulsion shafting is one of the main sources of ship vibration and noise. The shafting, whirling vibrations, and alignment are important factors that affect the comfort, stability, and reliability during a ship’s navigation. However, the mechanism of the interacting of the both factors is not fully revealed. In this paper, the effect of shafting alignment on whirling vibration and the bearing temperature response is studied by experiment. The test scheme is designed reasonably according to the theoretical analysis. The results show that the horizontal component of the shafting whirling vibration can be effectively reduced by adjusting the shafting alignment state while the vertical component is not. The shafting axis balancing position (SABP) slightly moves upward in high speed, which should be considered in the dynamic alignment design of the shafting, especially for the high-speed shafting. Little ABSB (the angle between the shafting centre line and the No. 1 bearing centre line) is beneficial to the stable operation of shafting, while appropriately increasing the ABSB and bearing load is beneficial to reducing the shafting whirling vibration. By balancing the relationship between bearing load and ABSB, the performance of whirling vibration and bearing temperature response can be optimized.

Predictive Failure Analysis of Solder Joints with Simultaneous High Speed EBSD and EDS

2018 ◽  
Author(s):  
J. Lindsay ◽  
P. Trimby ◽  
J. Goulden ◽  
S. McCracken ◽  
R. Andrews
Keyword(s):  
High Speed ◽  
Solder Joints ◽  
Phase Distribution ◽  
Bond Failure ◽  
Microstructural Parameters ◽  
Snpb Solder ◽  
Grain Orientations ◽  
Accelerated Thermal Cycling ◽  
The Relationship ◽  
Opening Up

Abstract The results presented here show how high-speed simultaneous EBSD and EDS can be used to characterize the essential microstructural parameters in SnPb solder joints with high resolution and precision. Analyses of both intact and failed solder joints have been carried out. Regions of strain localization that are not apparent from the Sn and Pb phase distribution are identified in the intact bond, providing key insights into the mechanism of potential bond failure. In addition, EBSD provides a wealth of quantitative detail such as the relationship between parent Sn grain orientations and Pb coarsening, the morphology and distribution of IMCs on a sub-micron scale and accurate grain size information for all phases within the joint. Such analyses enable a better understanding of the microstructural developments leading up to failure, opening up the possibility of improved accelerated thermal cycling (ATC) testing and better quality control.

Stable operation of multiple-lateral-mode ridge-waveguide lasers for high-speed printing

1997 ◽  
Vol 33 (3) ◽  
pp. 214
Author(s):  
R. LaComb ◽  
D.K. Wagner ◽  
L. DiMarco ◽  
J. Connolly
Keyword(s):  
High Speed ◽  
Ridge Waveguide ◽  
Stable Operation ◽  
Waveguide Lasers ◽  
Lateral Mode ◽  
Ridge Waveguide Lasers

scholarly journals Research on the Ignition Height and Reaction Flame Temperature of PTFE/Al/Si/CuO with Different Mass Ratios of PTFE/Si

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3464
Author(s):  
Xuan Zou ◽  
Jingyuan Zhou ◽  
Xianwen Ran ◽  
Yiting Wu ◽  
Ping Liu ◽  
...  
Keyword(s):  
Energy Release ◽  
High Speed ◽  
Flame Temperature ◽  
Sintering Process ◽  
Release Process ◽  
Reactive Material ◽  
Temperature Changes ◽  
Release Capacity ◽  
Mass Ratios ◽  
The Relationship

Recent studies have shown that the energy release capacity of Polytetrafluoroethylene (PTFE)/Al with Si, and CuO, respectively, is higher than that of PTFE/Al. PTFE/Al/Si/CuO reactive materials with four proportions of PTFE/Si were designed by the molding–sintering process to study the influence of different PTFE/Si mass ratios on energy release. A drop hammer was selected for igniting the specimens, and the high-speed camera and spectrometer systems were used to record the energy release process and the flame spectrum, respectively. The ignition height of the reactive material was obtained by fitting the relationship between the flame duration and the drop height. It was found that the ignition height of PTFE/Al/Si/CuO containing 20% PTFE/Si is 48.27 cm, which is the lowest compared to the ignition height of other Si/PTFE ratios of PTFE/Al/Si/CuO; the flame temperature was calculated from the flame spectrum. It was found that flame temperature changes little for the same reactive material at different drop heights. Compared with the flame temperature of PTFE/Al/Si/CuO with four mass ratios, it was found that the flame temperature of PTFE/Al/Si/CuO with 20% PTFE/Si is the highest, which is 2589 K. The results show that PTFE/Al/Si/CuO containing 20% PTFE/Si is easier to be ignited and has a stronger temperature destruction effect.

scholarly journals Improvement of Tilting-Pad Journal Bearing Operating Characteristics by Application of Eddy Grooves

Lubricants ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 18
Author(s):  
Eckhard Schüler ◽  
Olaf Berner
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Load Capacity ◽  
Fluid Film ◽  
Operating Characteristics ◽  
Fluid Film Bearings ◽  
Tilting Pad ◽  
Bearing Load ◽  
Bearing Loads ◽  
Tilting Pad Journal Bearing

In high speed, high load fluid-film bearings, the laminar-turbulent flow transition can lead to a considerable reduction of the maximum bearing temperatures, due to a homogenization of the fluid-film temperature in radial direction. Since this phenomenon only occurs significantly in large bearings or at very high sliding speeds, means to achieve the effect at lower speeds have been investigated in the past. This paper shows an experimental investigation of this effect and how it can be used for smaller bearings by optimized eddy grooves, machined into the bearing surface. The investigations were carried out on a Miba journal bearing test rig with Ø120 mm shaft diameter at speeds between 50 m/s–110 m/s and at specific bearing loads up to 4.0 MPa. To investigate the potential of this technology, additional temperature probes were installed at the crucial position directly in the sliding surface of an up-to-date tilting pad journal bearing. The results show that the achieved surface temperature reduction with the optimized eddy grooves is significant and represents a considerable enhancement of bearing load capacity. This increase in performance opens new options for the design of bearings and related turbomachinery applications.

Roller–rail parameters on the transverse vibration characteristics of super-high-speed elevators

2019 ◽  
Vol 43 (4) ◽  
pp. 535-543 ◽  
Author(s):  
Shunxin Cao ◽  
Ruijun Zhang ◽  
Shuohua Zhang ◽  
Shuai Qiao ◽  
Dongsheng Cong ◽  
...  
Keyword(s):  
High Speed ◽  
Relative Displacement ◽  
Guide Rail ◽  
Coupled Vibration ◽  
Vibration Acceleration ◽  
Vibration Model ◽  
Vibration Problems ◽  
Equivalent Method ◽  
Relationship Of ◽  
The Relationship

Interaction and wear between wheel and rail become increasingly serious with the increase in elevator speed and load. Uneven roller surface, eccentricity of rollers, and the looseness of rail brackets result in serious vibration problems of high-speed and super-high-speed elevators. Therefore, the forced vibration differential equation representing elevator guide rails is established based on Bernoulli–Euler theory, and the vibration equation of the elevator guide shoes and the car is constructed using the Darren Bell principle. Then, the coupled vibration model of guide rail, guide shoes, and car can be obtained using the relationship of force and relative displacement among these components. The roller–rail parameters are introduced into the established coupled vibration model using the model equivalent method. Then, the influence of roller–rail parameters on the horizontal vibration of super-high-speed elevator cars is investigated. Roller eccentricity and the vibration acceleration of the car present a linear correlation, with the amplitude of the car vibration acceleration increasing with the eccentricity of the roller. A nonlinear relationship exists between the surface roughness of the roller and the vibration acceleration of the car. Increased continuous loosening of the guide rail results in severe vibration of the car at the loose position of the support.

Interpretation of shadowgraph patterns in Rayleigh-Bénard convection

1988 ◽  
Vol 190 ◽  
pp. 451-469 ◽  
Author(s):  
D. R. Jenkins
Keyword(s):  
Rayleigh Number ◽  
Linear Theory ◽  
Vertical Component ◽  
Fluid Flows ◽  
Bénard Convection ◽  
Benard Convection ◽  
Higher Order Terms ◽  
The Relationship ◽  
Rayleigh Benard Convection ◽  
Rayleigh Benard

The relationship between observations of cellular Rayleigh-Bénard convection using shadowgraphs and theoretical expressions for convection planforms is considered. We determine the shadowgraphs that ought to be observed if the convection is as given by theoretical expressions for roll, square or hexagonal planforms and compare them with actual experiments. Expressions for the planforms derived from linear theory, valid for low supercritical Rayleigh number, produce unambiguous shadowgraphs consisting of cells bounded by bright lines, which correspond to surfaces through which no fluid flows and on which the vertical component of velocity is directed downwards. Dark spots at the centre of cells, indicating regions of hot, rising fluid, are not accounted for by linear theory, but can be produced by adding higher-order terms, predominantly due to the temperature dependence of a material property of the fluid, such as its viscosity.

Numerical and experimental studies on the thermal and static characteristics of multi-leaf foil thrust bearing

2021 ◽  
pp. 135065012110110
Author(s):  
Yu Guo ◽  
Yu Hou ◽  
Qi Zhao ◽  
Xionghao Ren ◽  
Shuangtao Chen ◽  
...  
Keyword(s):  
High Speed ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Failure Process ◽  
Experimental Studies ◽  
Elastic Model ◽  
Static Characteristics ◽  
Bearing Load ◽  
Foil Thrust Bearing ◽  
Cooling Air

Foil bearing is considered to be a promising supporting technology in high-speed centrifugal machinery. Due to the high-speed shearing effect in the viscous lubricant film, heat generation could not be ignored. In this paper, a thermo-elastic model of the multi-leaf foil thrust bearing is proposed to predict its thermal and static characteristics. In the model, modified Reynolds equation, energy equation, and Kirchhoff equation are solved in a coupling way. The contact area between the foil and welding plate is taken into account. Besides, the effect of cooling air on the bearing temperature is investigated. The ultimate load capacity and transient overload failure process of the bearing is analyzed and discussed. The effect of rotation speed on the bearing temperature is more obvious than that of the bearing load. The bearing temperature drops obviously by introducing the cooling air, and the cooling effect is improved with the supply pressure. The transient overload failure of the bearing occurs when the bearing load exceeds the ultimate value.

Is Dynamic Spino-Pelvic Alignment During Gait Associated with Quality of Life in Patients with Degenerative Lumbar Spinal Canal Stenosis?

2021 ◽  
Author(s):  
Takuya Miura ◽  
Ryoji Tominaga ◽  
Keita Sato ◽  
Tatsuya Endo ◽  
Masumi Iwabuchi ◽  
...  
Keyword(s):  
Spinal Canal Stenosis ◽  
Lumbar Spinal Canal Stenosis ◽  
Canal Stenosis ◽  
Lumbar Spinal ◽  
Trunk Extension ◽  
The Relationship ◽  
Hip Extension ◽  
Dynamic Alignment ◽  
Spinal Flexion

Abstract This study aims to investigate the relationship between dynamic alignment of the spine and pelvis during gait and quality of life (QOL) in lumbar spinal canal stenosis (LSS) patients. We evaluated QOL using the Oswestry Disability Index (ODI), trunk and hip muscle strength as physical function, static spinal alignment, and dynamic spinal/pelvic alignment during gait. The relationship between the ODI score and physical function or static and dynamic alignment were examined. A total of 30 preoperative patients with LSS were participated in this study. ODI score significantly correlated with trunk extension strength (r = -0.559, p = 0.002), hip extension strength (r = -0.473, p = 0.011), maximum flexion angle of spine during gait (r = -0.551, p = 0.002) and maximum anterior tilt angle of pelvis (r = 0.528, p = 0.004). Multiple regression analysis showed that trunk extension strength (standardized β; - 0.35), maximum spinal flexion angle (standardized β; - 0.51) and hip extension strength (standardized β; - 0.40) significantly affected the ODI score, with adjusted coefficient of determination of 0.62. The results of this study showed that the LSS patients with weak hip or trunk extensor muscles, a greater angle of pelvic tilt or a less spinal flexion during gait had a lower QOL.

Characteristics of Stable Rotating Stall Cells in an Axial Compressor

2017 ◽  
Author(s):  
Adam R. Hickman ◽  
Scott C. Morris
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Axial Compressor ◽  
Field Measurements ◽  
Rotating Stall ◽  
Flow Coefficient ◽  
Stable Operation ◽  
Double Phase

Flow field measurements of a high-speed axial compressor are presented during pre-stall and post-stall conditions. The paper provides an analysis of measurements from a circumferential array of unsteady shroud static pressure sensors during stall cell development. At low-speed, the stall cell approached a stable size in approximately two rotor revolutions. At higher speeds, the stall cell developed within a short amount of time after stall inception, but then fluctuated in circumferential extent as the compressor transiently approached a stable post-stall operating point. The size of the stall cell was found to be related to the annulus average flow coefficient. A discussion of Phase-Locked Average (PLA) statistics on flow field measurements during stable operation is also included. In conditions where rotating stall is present, flow field measurements can be Double Phase-Locked Averaged (DPLA) using a once-per-revolution (1/Rev) pulse and the period of the stall cell. The DPLA method provides greater detail and understanding into the structure of the stall cell. DPLA data indicated that a stalled compressor annulus can be considered to contained three main regions: over-pressurized passages, stalled passages, and recovering passages. Within the over-pressured region, rotor passages exhibited increased blade loading and pressure ratio compared to pre-stall values.

Effect of links deformation on motion precision of parallel manipulator based on flexible dynamics

2017 ◽  
Vol 44 (6) ◽  
pp. 776-787 ◽  
Author(s):  
Chunxia Zhu ◽  
Jay Katupitiya ◽  
Jing Wang
Keyword(s):  
Parallel Manipulator ◽  
High Speed ◽  
Beam Theory ◽  
Parallel Manipulators ◽  
Dynamic Responses ◽  
Axial Deformation ◽  
Content Type ◽  
High Performing ◽  
Coupling Equations ◽  
The Relationship

Purpose Manipulator motion accuracy is a fundamental requirement for precision manufacturing equipment. Light weight manipulators in high speed motions are vulnerable to deformations. The purpose of this work is to analyze the effect of link deformation on the motion precision of parallel manipulators. Design/methodology/approach The flexible dynamics model of the links is first established by applying the Euler–Bernoulli beam theory and the assumed modal method. The rigid-flexible coupling equations of the parallel mechanism are further derived by using the Lagrange multiplier approach. The elastic energy resulting from spiral motion and link deformations are computed and analyzed. Motion errors of the 3-link torque-prismatic-torque parallel manipulator are then evaluated based on its inverse kinematics. The validation experiments are also conducted to verify the numerical results. Findings The lateral deformation and axial deformation are largest at the middle of the driven links. The axial deformation at the middle of the driven link is approximately one-tenth of the transversal deformation. However, the elastic potential energy of the transversal deformation is much smaller than the elastic force generated from axial deformation. Practical implications Knowledge on the relationship between link deformation and motion precision is useful in the design of parallel manipulators for high performing dynamic responses. Originality/value This work establishes the relationship between motion precision and the amount of link deformation in parallel manipulators.

Sign in / Sign up

Export Citation Format

Share Document