scholarly journals Experimental Study on Fluid Properties of Cement-Fly Ash Slurry Subjected to Multifactors

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
Tian Huang ◽  
Feng Huang ◽  
Huifeng Zhou
Keyword(s):  
Fly Ash ◽  
Setting Time ◽  
Factors Affecting ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Initial Setting Time ◽  
Fluid Properties ◽  
Practical Engineering ◽  
Initial Setting ◽  
The Stability

There are many factors affecting the characteristics of cement-fly ash slurry in practical engineering. Thus, this paper studies the influence of multifactors on the fluid properties of cement-fly ash slurry based on water-cement ratio ( w / c ) (0.75, 1, 1.25, and 1.5), fly ash content (0%, 10%, 20%, 30%, 40%, and 50%) and temperature (20°C, 40°C, 60°C, and 80°C). The bleeding ratio, initial setting time, final setting time, and viscosity were analyzed under coupling conditions. It is found that the water-cement ratio ( w / c ) is the main factor that affects the rheological properties and bleeding rate of slurry. The temperature affects the stability of the slurry in terms that the bleeding ratio of the slurry decreases as the temperature increases. The addition of fly ash enhances the stability of the slurry under different temperature conditions.

Evaluation of initial setting time due to superplasticizers

2017 ◽  
Vol 8 (2) ◽  
pp. 65
Author(s):  
Abhishek Singh ◽  
Shobha Ram ◽  
Alok Verma
Keyword(s):  
Water Content ◽  
Cement Paste ◽  
Setting Time ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Initial Setting Time ◽  
Initial Setting

This paper shows how polycarboxylate based superplasticizer affects the initial setting time of cement paste. Three superplasticizers are used in this study with different properties and aiming to determine the delay in initial setting time due to superplasticizer. Initial setting time is calculated as per IS: 4031-PART 5-1988 with different SP dosages (0.5%, 0.75%, 1.0% and 1.5% of weight of cement). Superplasticizer is an admixture which reduces the water-cement ratio or increase the workability at the same water content. This paper deals with the evaluation of initial setting time due to superplasticizers.

Preliminary Study on Reaction of Fresh Concrete with Carbon Dioxide

2018 ◽  
Vol 382 ◽  
pp. 230-234
Author(s):  
Ming Ju Lee ◽  
Ming Gin Lee ◽  
Yung Chih Wang ◽  
Yu Min Su ◽  
Jia Lun Deng
Keyword(s):  
Carbon Dioxide ◽  
Compressive Strength ◽  
Fresh Concrete ◽  
Setting Time ◽  
Cement Matrix ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Short Time

In order to let fresh concrete react with carbon dioxide sufficiently, the carbon dioxide was added to mixing concrete. The study used three water cement ratio (0.55, 0.65, 0.75), three CO2 pressures (0.2, 0.4, 0.6 MPa), and two CO2 concentration (50% and 100%) to make concrete samples, and observed the effect of carbon dioxide adsorption in the above parameters. Finally, the compressive strength and carbonation degree of concretes were tested after three curing time (7, 14 and 28 days). The research showed that concrete could be more efficient to absorb carbon dioxide by using this pressure method. The results found that the mixing concrete react with carbon dioxide in a short time, and shorten the initial setting time of concrete. But this method would greatly reduce the workability of concrete after mixing with carbon dioxide and it might be enhanced by water or superplasticizer. The bond of cement matrix might cut down after reacting with carbon dioxide. Based on the above, the compressive strength of concrete which was mixed with carbon dioxide would be impaired. The proposed CO2-mixing method has the capacity to uptake 9.5% carbon dioxide based on water cement ratio and CO2 pressure.

scholarly journals Properties of non-standard fly ash – slag cements containing calcareous fly ash

2013 ◽  
Vol 12 (3) ◽  
pp. 215-222
Author(s):  
Katarzyna Synowiec
Keyword(s):  
Fly Ash ◽  
Blast Furnace Slag ◽  
Strength Class ◽  
Setting Time ◽  
Heat Of Hydration ◽  
Initial Setting Time ◽  
Granulated Blast Furnace Slag ◽  
Unfavorable Effect ◽  
Initial Setting ◽  
Furnace Slag

The paper presents the tests results of the properties of non - standard fly ash - slag cements composition. Both natural (unprocessed) and activated by grinding calcareous fly ash was used. It was found that the calcareous fly ash next to the granulated blast furnace slag may be a component of low - clinker cements (ca. 40%). Those cements are characterized by low heat of hydration and overdue of initial setting time in comparison with Ordinary Portland Cement, moreover they have an unfavorable effect on consistency and its upkeep in time. Production of fly ash - slag cements is possible for strength class 32,5 N when the component of cement is raw fly ash, and for strength classes 32,5 N, 32,5 R and 42,5 N when ground fly ash was used. Fly ash activated by grinding was characterized by higher activity.

Evaluation of Fresh Properties and Rheology of Mortar Using Carbon-Free Fly Ash and Normal Fly Ash

2020 ◽  
Vol 1005 ◽  
pp. 76-81
Author(s):  
Ghawsaddin Nazari ◽  
Shunya Yamanaka ◽  
Shigeyuki Date
Keyword(s):  
Fly Ash ◽  
Setting Time ◽  
Great Influence ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Fresh Properties ◽  
Initial Setting Time ◽  
Usual Solution ◽  
Initial Setting ◽  
Flow Loss

Usage of mineral admixture and chemical admixture in concrete or mortar is a usual solution to reach full compaction, particularly where reinforcement blockage and lack of skilled labor happen. In this paper effect of mineral admixtures (Carbon-free fly ash, hereafter CfFA, and normal fly ash) on fresh properties and rheology of mortar have been investigated. As a result, it was confirmed that CfFA increased significantly the fluidity and air content of mortar in comparison to normal fly ash, both in 15% and 30% replacement; however, the flow loss and air stability within one hour were almost equal. In addition, the initial setting time has also been affected by variation of materials. The two mixing of 30% and 15% of CfFA had a shorter setting time in comparison to the mortar with normal fly ash. Furthermore, CfFA based mortar had a great influence on rheology of mortar. Compared to normal fly ash, CfFA Considerably decreased the plastic Viscosity and increased the productivity of the mortar, both in non-vibrated and vibrated condition, particularly those with 30% replacement.

Environmental Friendly Sulphoaluminate Cement Based Rapid Hardening and Repair Materials

2014 ◽  
Vol 548-549 ◽  
pp. 12-15 ◽  
Author(s):  
Meng Jie Lu ◽  
Ming Fang Ba ◽  
Dan Yi Man ◽  
Si Yuan Ma ◽  
Jie Yang ◽  
...  
Keyword(s):  
Fly Ash ◽  
Silica Fume ◽  
Setting Time ◽  
Mass Ratio ◽  
Rapid Hardening ◽  
Initial Setting Time ◽  
Sulphoaluminate Cement ◽  
Repair Materials ◽  
Initial Setting ◽  
Working Performance

In order to save the costs of the rapid hardening and repair sulphoaluminate cement and improve its working performance, the effects of slag, fly ash, silica fume in different contents and different adding ways on the initial setting time and working performance of sulphoaluminate cement are studied. The results show that the initial setting time of single-doped slag and fly ash both meet the requirements of repair materials, but silica fume significantly cuts the cement’s initial setting time short, which does not meet the construction conditions for rapid hardening and repair. Ultimately it is determined that the mechanical properties of sulphoaluminate cement are the best when slag and fly ash are compound added by the content of 30% at 4:1 mass ratio and simultaneously the initial setting time meets the conditions for rapid hardening and repair.

Properties of slag geopolymer concrete modified with fly ash and silica fume

2021 ◽  
Author(s):  
Hafez Elsayed Elyamany ◽  
Abd Elmoaty Mohamed Abd Elmoaty ◽  
Abdul Rahman Ahmed Diab
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Setting Time ◽  
Splitting Tensile Strength ◽  
Geopolymer Concrete ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Additional Water

This research focused on the role of fly ash and silica fume on slag geopolymer concrete through investigating workability (slump, and slump loss), initial setting time, final setting time, and mechanical properties of slag geopolymer concrete, S-GPC, (compressive strength, splitting tensile strength, modulus of elasticity) in addition to SEM (Scanning electron microscope), and X-Ray analysis. The considered variables included, fly ash (FA) content as a replacement of ground granulated blast furnace slag (GS) (0, 10, 20, 30, and 40 %), presence of silica fume (SF) as a replacement of slag, concentration of sodium hydroxide, NaOH, (molarity: 10M, 16M, and 18M), additional water content (7.5,11,14, and 20 %), and curing type (thermal, air, and water curing). S-GPC yielded rapid stiffening and high slump loss with high mechanical properties. The use of silica fume or fly ash or a mix of them enhanced workability, decreased rate of slump loss, and delayed setting time. ACI 318 equation over estimates splitting tensile strength of FS-GPC.

Survey on Factors Affecting Impermeability of Waterproof Concrete

2011 ◽  
Vol 250-253 ◽  
pp. 1320-1323
Author(s):  
Yi Jin Li ◽  
Yun Li Gong ◽  
Jian Yin
Keyword(s):  
Fly Ash ◽  
Ash Content ◽  
Raw Material ◽  
Factors Affecting ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Mix Proportion

This paper describes the influence of raw material, water-cement ratio, sand ratio, cement-sand ratio and fly ash content on impermeability of waterproof concrete. The value ranges of several important mix parameters are summarized, that provides the reference to select the parameters of mix proportion of waterproof concrete for subway.

Study on Preparation and the Setting Time of Magnesium Phosphate Cement

2014 ◽  
Vol 1049-1050 ◽  
pp. 251-255
Author(s):  
Run Qing Liu ◽  
Ding Qiang Chen ◽  
Tian Bo Hou
Keyword(s):  
Fly Ash ◽  
Orthogonal Experiment ◽  
Setting Time ◽  
Magnesium Phosphate ◽  
Mixture Ratio ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Orthogonal Analysis ◽  
Optimal Mixture Ratio

This paper mainly researched on preparation and the setting time of Magnesium Phosphate Cement (MPC). The method of orthogonal experiment was adapted to determine the best ratio of MPC, and change the content and types of the material according to the influence of various factors, so as to get the longer setting time of MPC. The results showed that, when the water cement ratio is 0.12, the factors significantly influencing the setting time is magnesium phosphorus ratio (M/P), fly ash and borax. The optimal mixture ratio was obtained through the orthogonal analysis, namely M/P is 3/1, borax content is 16%, and the amount of fly ash is 40%. When M/P is 1/1 and 2/2, borax content is not more than 22%, and the amount of fly ash was less than 60%, the longer setting time of MPC can be produced.

scholarly journals Investigation on the Compressive Strength and Time of Setting of Low-Calcium Fly Ash Geopolymer Paste Using Response Surface Methodology

Polymers ◽  
2021 ◽  
Vol 13 (20) ◽  
pp. 3461
Author(s):  
Pauline Rose J. Quiatchon ◽  
Ithan Jessemar Rebato Dollente ◽  
Anabel Balderama Abulencia ◽  
Roneh Glenn De Guzman Libre ◽  
Ma. Beatrice Diño Villoria ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Unconfined Compressive Strength ◽  
Setting Time ◽  
Initial Setting Time ◽  
Alkali Activator ◽  
Setting Times ◽  
Confirmatory Tests ◽  
Initial Setting

Approximately 2.78 Mt of coal fly ash is produced in the Philippines, with a low utilization rate. Using fly ash-based geopolymer for construction will lessen the load sent to landfills and will result in lower GHG emissions compared to OPC. It is necessary to characterize the fly ash and optimize the geopolymer components to determine if it can replace OPC for in situ applications. The activator-to-precursor ratio, the water-to-solids ratio, and the sodium hydroxide-to-sodium silicate ratio were optimized using a randomized I-optimal design from the experimental results of 21 runs with five replicates, for a total of 105 specimens of 50 mm × 50 mm × 50 mm paste cubes. The engineering properties chosen as the optimization responses were the unconfined compressive strength (UCS), the initial setting time, and the final setting time. The samples were also ambient-cured with the outdoor temperature ranging from 30 °C to 35 °C and relative humidity of 50% ± 10% to simulate the on-site environment. Runs with high unconfined compressive strength (UCS) and short setting times were observed to have a low water-to-solids (W/S) ratio. All runs with a UCS greater than 20 MPa had a W/S ratio of 0.2, and the runs with the lowest UCS had a W/S of 0.4. The initial setting time for design mixes with a W/S ratio of 0.2 ranged from 8 to 105 min. Meanwhile, five out of seven design mixes with a W/S ratio of 0.4 took longer than 1440 min to set. Specimens with an alkali activator ratio (NaOH/WG) of 0.5 (1:2) and 0.4 (1:2.5) also had significantly lower setting times than those with an alkali activator ratio of 1. The RSM model was verified through confirmatory tests. The results of the confirmatory tests are agreeable, with deviations from the expected UCS ranging from 0 to 38.12%. The generated model is a reliable reference to estimate the UCS and setting time of low-calcium FA geopolymer paste for in situ applications.

scholarly journals Investigation of Portland cement composites containing high amounts of different kinds of fly ashes

2019 ◽  
Author(s):  
Iwona Wilińska ◽  
Barbara Pacewska ◽  
Wojciech Kubissa
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Cement Composite ◽  
Fly Ashes ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Lower Heat ◽  
The Impact

Utilization of fluidized fly ash in cement composite is problematic, e.g. because of its changeable chemical composition and increased water demand of the mixture. However, this kind of by-product shows some self-cementing properties, which may be beneficial for low-cement mixtures. The article compares the impact of various kinds of fly ashes, i.e. fluidized fly ash and conventional one, and their mixtures on hydration of fly ash–cement compositions in relation to properties of final material. The amount of fly ash in the binder was 50 wt%. Calorimetry, thermal analysis (TG/DTG) and infrared spectroscopy were used. Compressive strength and water absorption of hardened composites were also registered. It was found that both fly ashes exhibit delay effect in fly ash-cement pastes which causes extension of initial setting time and lower heat released compared to the reference without fly ash. At later hydration days, fluidized fly ash develops higher pozzolanic activity than conventional one. Compositions with fluidized fly ash show better compressive strength compared to those containing conventional one. Mixing of different materials of high and low activity (fluidized and conventional fly ash in this case) seems to be a good way for creation of new cement replacement material.

Sign in / Sign up

Export Citation Format

Share Document