Wettability Control of Gold Surfaces Modified with Benzenethiol Derivatives: Water Contact Angle and Thermal Stability

2016 ◽  
Vol 16 (4) ◽  
pp. 3295-3300 ◽  
Author(s):  
Shingo Tatara ◽  
Yasutaka Kuzumoto ◽  
Masatoshi Kitamura

The water wettability of Au surfaces has been controlled using various benzenethiol derivatives including 4-methylbenzenethiol, pentafluorobenzenethiol, 4-fluorobenzenethiol, 4-methoxybenzenethiol, 4-nitrobenzenethiol, and 4-hydroxybenzenethiol. The water contact angle of the Au surface modified with the benzenethiol derivative was found to vary in the wide range of 30.9° to 88.3°. The contact angle of the modified Au films annealed was also measured in order to investigate their thermal stability. The change in the contact angle indicated that the modified surface is stable at temperatures below about 400 K. Meanwhile, the activation energy of desorption from the modified surface was estimated from the change in the contact angle. The modified Au surface was also examined using X-ray photoelectron spectroscopy.

2018 ◽  
Vol 2 (4) ◽  
pp. 74 ◽  
Author(s):  
Abinash Tripathy ◽  
Patryk Wąsik ◽  
Syama Sreedharan ◽  
Dipankar Nandi ◽  
Oier Bikondoa ◽  
...  

Functional ZnO nanostructured surfaces are important in a wide range of applications. Here we report the simple fabrication of ZnO surface structures at near room temperature with morphology resembling that of sea urchins, with densely packed, μm-long, tapered nanoneedles radiating from the urchin center. The ZnO urchin structures were successfully formed on several different substrates with high surface density and coverage, including silicon (Si), glass, polydimethylsiloxane (PDMS), and copper (Cu) sheets, as well as Si seeded with ZnO nanocrystals. Time-resolved SEM revealed growth kinetics of the ZnO nanostructures on Si, capturing the emergence of “infant” urchins at the early growth stage and subsequent progressive increases in the urchin nanoneedle length and density, whilst the spiky nanoneedle morphology was retained throughout the growth. ε-Zn(OH)2 orthorhombic crystals were also observed alongside the urchins. The crystal structures of the nanostructures at different growth times were confirmed by synchrotron X-ray diffraction measurements. On seeded Si substrates, a two-stage growth mechanism was identified, with a primary growth step of vertically aligned ZnO nanoneedle arrays preceding the secondary growth of the urchins atop the nanoneedle array. The antibacterial, anti-reflective, and wetting functionality of the ZnO urchins—with spiky nanoneedles and at high surface density—on Si substrates was demonstrated. First, bacteria colonization was found to be suppressed on the surface after 24 h incubation in gram-negative Escherichia coli (E. coli) culture, in contrast to control substrates (bare Si and Si sputtered with a 20 nm ZnO thin film). Secondly, the ZnO urchin surface, exhibiting superhydrophilic property with a water contact angle ~ 0°, could be rendered superhydrophobic with a simple silanization step, characterized by an apparent water contact angle θ of 159° ± 1.4° and contact angle hysteresis ∆θ < 7°. The dynamic superhydrophobicity of the surface was demonstrated by the bouncing-off of a falling 10 μL water droplet, with a contact time of 15.3 milliseconds (ms), captured using a high-speed camera. Thirdly, it was shown that the presence of dense spiky ZnO nanoneedles and urchins on the seeded Si substrate exhibited a reflectance R < 1% over the wavelength range λ = 200–800 nm. The ZnO urchins with a unique morphology fabricated via a simple route at room temperature, and readily implementable on different substrates, may be further exploited for multifunctional surfaces and product formulations.


2017 ◽  
Vol 7 ◽  
pp. 184798041770279 ◽  
Author(s):  
Baojiang Liu ◽  
Taizhou Tian ◽  
Jinlong Yao ◽  
Changgen Huang ◽  
Wenjun Tang ◽  
...  

A robust superhydrophobic organosilica sol-gel-based coating on a cotton fabric substrate was successfully fabricated via a cost-effective one-step method. The coating was prepared by modification of silica nanoparticles with siloxane having long alkyl chain that allow to reduce surface energy. The coating on cotton fabric exhibited water contact angle of 151.6°. The surface morphology was evaluated by scanning electron microscopy, and surface chemical composition was measured with X-ray photoelectron spectroscopy. Results showed the enhanced superhydrophobicity that was attributed to the synergistic effect of roughness created by the random distribution of silica nanoparticles and the low surface energy imparted of long-chain alkane siloxane. In addition, the coating also showed excellent durability against washing treatments. Even after washed for 30 times, the specimen still had a water contact angle of 130°, indicating an obvious water-repellent property. With this outstanding property, the robust superhydrophobic coating exhibited a prospective application in textiles and plastics.


2006 ◽  
Vol 15-17 ◽  
pp. 187-192 ◽  
Author(s):  
Ko Shao Chen ◽  
Su Chen Chen ◽  
Yi Chun Yeh ◽  
Wei Cheng Lien ◽  
Hong Ru Lin ◽  
...  

Expanded polytetrafluoroethylene (ePTFE) is a bioinert material. To improve the ePTFE film biocompatibility, the cold plasma technology was used with acetic acid as monomer to deposit onto ePTFE film and then (N-isopropylacrylamide) was grafted onto the surface by photo-grafting. The characteristics of the surface were evaluated with X-ray photoelectron spectroscopy (XPS), FTIR and water contact angle. It was found that the contact angle of water on the untreated ePTFE significantly decrease from125° to 72° after ePTFE film being treated with acetic acid plasma deposition treatment. Due to the hydrophilicity of poly(N-isopropylacrylamide), the contact angle of water on the ePTFE-g-NIPAAm approached to 0°.


2021 ◽  
Author(s):  
Guangfeng Wu ◽  
Xin Song ◽  
ZhiHui Yang ◽  
Ying Chun Li ◽  
HuiXuan Zhang

Abstract Polyester diol PCL and PBA, polyether diol PTMG and polycarbonate diol PCDL were used as components of WPU soft segment, respectively. Polyether PTMG-WPU has the worst hydrolytic property and the highest thermal stability. The maximum degradation rate temperature Tmax is 407.8°C, the water contact angle reaches 89.5°. Traditional polyester PCL-WPU shows the strongest hydrolysis performance, the smallest water contact angle, only 71.7°, the water absorption rate of 72 hours at room temperature is as high as 26.7%. However, the thermal stability of PCL-WPU is lower, the soft segment Tg is -52.3°C, and Tmax is only 333.7°C, but the mechanical propertie of which is the best, the tensile strength is 58.3 MPa, and the elongation at break reaches 857.9%. The most important thing is that the structure of polyester PCL-WPU is more easily destroyed by lipase and water molecules. The acidic products produced after hydrolysis will further promote the degradation of polyester. Therefore, compared with other WPUs, PCL -WPU has the best biodegradability and the most obvious degradation effect under the same conditions. The degradation rate of PTMG-WPU after 30 days of degradation in 0.6% lipase PBS buffer solution and soil was only 4.2% and 2.3%, while the highest degradation rate of traditional polyester PCL-WPU reached 41.7% and 32.0%, respectively. In addition, polycarbonate PCDL-WPU has the highest hardness, reaching 95.5 HD. But its other performances are lower than PCl-WPU.


2011 ◽  
Vol 306-307 ◽  
pp. 1631-1634 ◽  
Author(s):  
Ya Kai Feng ◽  
Da Zhi Yang ◽  
Hai Yang Zhao ◽  
Jin Tang Guo ◽  
Qing Liang Chen ◽  
...  

Poly(3-dimethyl(methacryloyloxyethyl)ammonium propane sulfonate) (poly(DMAPS)) zwitterionic brushes were grafted onto the polycarbonateurethane (PCU) surface to improve its hydrophilicity and hemocompatibility by Ultraviolet (UV) polymerization. Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS) and water contact angle were used to characterize the chemical and physical properties of the modified PCU surface. DMAPS-grafted PCU films showed significantly high hydrophilicity owing to the high hydrophilic poly(DMAPS) zwitterionic brushes. The cytotoxicity tests revealed the sulfoammonium zwitterionic brushes modified PCU film had good cytocompatibility. In addition, the hemocompatibility of the modified PCU films was evaluated by hemolytic tests and platelet adhesion tests. The PCU films modified with zwitterionic brushes had a lower hemolytic index, showed effective resistance to platelet adhesion. Due to the fact that sulfoammonium zwitterionic brushes can improve the hemocompatibility of the PCU surface, this gives rise to its potential application as blood-contacting materials or devices.


2021 ◽  
Vol 22 (13) ◽  
pp. 6672
Author(s):  
Nina Recek ◽  
Matej Holc ◽  
Alenka Vesel ◽  
Rok Zaplotnik ◽  
Peter Gselman ◽  
...  

Seeds of common bean (Phaseolus vulgaris L.), of the Etna variety, were treated with low-pressure oxygen plasma sustained by an inductively coupled radiofrequency discharge in the H-mode for a few seconds. The high-intensity treatment improved seed health in regard to fungal contamination. Additionally, it increased the wettability of the bean seeds by altering surface chemistry, as established by X-ray photoelectron spectroscopy, and increasing surface roughness, as seen with a scanning electron microscope. The water contact angle at the seed surface dropped to immeasurably low values after a second of plasma treatment. Hydrophobic recovery within a month returned those values to no more than half of the original water contact angle, even for beans treated for the shortest time (0.5 s). Increased wettability resulted in accelerated water uptake. The treatment increased the bean radicle length, which is useful for seedling establishment in the field. These findings confirm that even a brief plasma treatment is a useful technique for the disinfection and stimulation of radicle growth. The technique is scalable to large systems due to the short treatment times.


2013 ◽  
Vol 747 ◽  
pp. 182-185
Author(s):  
Tharinee Theerathanagorn ◽  
Boonlom Thavornyutikarn ◽  
Wanida Janvikul

In this study, poly (glycerol sebacate) (PGS) was initially synthesized via condensation polymerization of glycerol and sebacic acid at equimolar ratio (1:1) at 130°C for 24 h. The number average molecular weight (Mn) of the resulting polymer determined by gel permeation chromatography (GPC) was about 2800 g/mol. Porous PGS scaffolds were subsequently prepared by a particle-leaching technique. NaCl was added into the polymer at 60-90% w/w; the mixtures were cured in Teflon molds at 140°C for 16 h. The porous scaffolds were further subjected to surface treatment with low pressure oxygen plasma to increase surface carboxyl and hydroxyl groups and thereby enhance hydrophilicity of PGS scaffold surface. The surface morphology and wettability of both untreated PGS and plasma-treated PGS scaffolds were comparatively determined by scanning electron microscopy (SEM) and water contact angle measurement, respectively. A considerable decrease in water contact angle was observed on the PGS scaffolds after the plasma treatment. The surface chemistry, mechanical strength and degree of swelling of the PGS scaffolds were also assessed by X-ray photoelectron spectroscopy (XPS), dynamic mechanical analysis (DMA) and swelling measurement, respectively.


2011 ◽  
Vol 306-307 ◽  
pp. 3-6
Author(s):  
Hai Yang Zhao ◽  
Ya Kai Feng ◽  
Da Zhi Yang ◽  
Jin Tang Guo ◽  
Qing Liang Chen ◽  
...  

In order to improve the hemocompatibility of polycarbonateurethane (PCU), the biomimetic phosphorylcholine (PC) group was introduced onto material surface. Brush structure having PC groups was formed by ultraviolet (UV) initiated polymerization of 2-methacryloyloxyethyl phosphorylcholine (MPC) to improve the hydrophilicity and hemocompatibility of PCU surfaces. Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electrical microscopy (SEM) and water contact angle were used to characterize the chemical and physical properties of the modified PCU surfaces. Compared with original PCU, the PC-grafted PCU surfaces showed significantly high hydrophilicity as indicating by low water contact angle. The hemocompatibility of the PC-grafted PCU surfaces was evaluated by platelet adhesion test. The PCU surfaces modified with phosphorylcholine zwitterionic brushes showed effective resistance to platelet adhesion and high hemocompatibility. These PC-grafted PCU materials will have potential application as blood-contacting materials or devices due to their good mechanical and hemocompatible properties.


2017 ◽  
Vol 89 (3) ◽  
pp. 401-410 ◽  
Author(s):  
Yongqiang Li ◽  
Chao Zou ◽  
Jianzhong Shao ◽  
Ya’nan Li

Cotton fabric is commonly used in daily life, but it is easily wetted and contaminated by liquid. Herein, we present a simple and environmentally friendly plasma technology for hydrophobic modification of cotton fabric. In order to endow superhydrophobicity to cotton fabric, helium plasma inducing graft polymerization of 1,3,5,7-tetravinyl-1,3,5,7-tetramethylcyclotetrasiloxane (D4Vi) was utilized to wrap SiO2 particles on cotton fabrics. Cotton fabrics were successively dipped in silica sol and D4Vi, then treated by plasma. Cotton fabrics before and after modification were characterized by using field emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and water contact angle measurement. The experimental results showed that the cotton-SiO2-D4Vi consisted of nanoscale SiO2 protrusions and low-surface-energy film polymerized by D4Vi. In addition, the one wrapped SiO2 of 161 nm presented excellent hydrophobicity, washing durability, and repellency toward different types of liquids with a water contact angle of 152°.


NANO ◽  
2020 ◽  
Vol 15 (12) ◽  
pp. 2050150
Author(s):  
Sifeng Zhang ◽  
Lulu Wang ◽  
Ziguang Zheng ◽  
Yunrui Hei ◽  
Luting Zhou ◽  
...  

In this study, BiOI was successfully synthesized using a hydrothermal method and then modified using hexamethyldisiloxane (HMDS) and polydimethylsiloxane (PDMS), respectively, to achieve a controllable water contact angle (WCA) for these materials. The physical and chemical properties of the modified BiOI were characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET) method, UV–Vis diffuse reflectance spectroscopy (DRS), Fourier transform infrared (FTIR) spectroscopy and water contact angle (WCA) techniques. Compared with the unmodified BiOI, HMDS- and PDMS-modified BiOI had higher photocatalytic activities for 17[Formula: see text]-ethinylestradiol (EE2) under visible light irradiation for 28 min after reacting in dark for 30 min. When BiOI was modified using HMDS and PDMS, the WCA increased. When the WCA of HMDS- and PDMS-modified BiOI was controlled in the range of 25.3–32.7[Formula: see text] and 38.1–78.5[Formula: see text], respectively, better photocatalytic performances were achieved. When the WCA of modified BiOI was 29.7[Formula: see text] (1.00[Formula: see text]mL HMDS) and 47.8[Formula: see text] (0.20[Formula: see text]mL PDMS), the best photocatalytic performances were achieved with EE2 removal rate of 98.85% and 98.72%, respectively, however, the removal rate of the unmodified BiOI was 85.01%. The reaction rate constants of BiOI (1.00[Formula: see text]mL HMDS) and BiOI (0.20[Formula: see text]mL PDMS) were 2.33 and 2.15 times higher than the unmodified BiOI, respectively. The improved catalytic performances of modified BiOI could be attributed to the synergistic effect of the controlled wettability of BiOI and functional groups on the surface of photocatalysts.


Sign in / Sign up

Export Citation Format

Share Document