Effects of Temperature–Humidity Treatment on Bending Reliability of Epoxy Sn–58Bi Solder with Electroless Nickel Immersion Gold (ENIG) and Electroless Nickel Electroless Palladium Immersion Gold (ENEPIG) Surface Finishes

2020 ◽  
Vol 12 (4) ◽  
pp. 564-570
Author(s):  
Haksan Jeong ◽  
Choong-Jae Lee ◽  
Woo-Ram Myung ◽  
Kyung Deuk Min ◽  
Seung-Boo Jung
Keyword(s):  
Intermetallic Compound ◽  
Solder Joint ◽  
Solder Joints ◽  
Solder Matrix ◽  
Electroless Nickel ◽  
Bending Test ◽  
Three Point Bending ◽  
Electroless Nickel Immersion Gold ◽  
Surface Finishes ◽  
Effects Of Temperature

An epoxy Sn–58wt.%Bi solder joint was evaluated by a three-point bending test with electroless nickel immersion gold (ENIG) and electroless nickel electroless palladium immersion gold (ENEPIG) surface finishes aged at 85 °C and 85% relative humidity. Scanning electron microscopy and electron probe microanalysis were carried out to study intermetallic compound variation. The morphology, total thickness, and chemical composition of intermetallic compound in epoxy Sn58Bi solder joints were the same as those of Sn–58wt.%Bi solder joints with each surface finish. The average number of bending-to-failure cycles for the epoxy Sn–58wt.%Bi solder/ENIG joints and epoxy Sn–58wt.%Bi solder/ENEPIG was more than 4000 and 5000, respectively. The average number of bending-to-failure cycles of the epoxy Sn–58wt.%Bi solder joint decreased with increasing age. Three-point bending reliability of epoxy Sn–58wt.%Bi solder joints was higher than that of Sn–58wt.%Bi solder with both surface finishes. Cracking of all solder joints subjected to as-reflowed was propagated through the solder matrix. However, after aging for 1000 h, cracking occurred primarily between intermetallic compound layers.

Comparison of Ball Pull Strength Among Various Sn-Cu-Ni Solder Joints With Different Pad Surface Finishes

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Chaoran Yang ◽  
Fubin Song ◽  
S. W. Ricky Lee
Keyword(s):  
Electron Microscopy ◽  
Intermetallic Compound ◽  
Intermetallic Compounds ◽  
High Speed ◽  
Solder Matrix ◽  
Electroless Nickel ◽  
Compound Layer ◽  
Intermetallic Compound Layer ◽  
Surface Finishes ◽  
Ternary Intermetallic Compounds

SnCuNi is one of the most common ternary intermetallic compounds formed in the Sn-based solder joint, and its formation and properties can be greatly influenced by the amount of Ni. Ni can participate in the interfacial reaction and diffuse into the intermetallic compound layer from either the solder or from the pad. In this research, comparative studies of different SnCuNi intermetallic compounds were conducted using two kinds of SnCuNi solders with organic solderability preservatives pad finish and a SnCu solder with electroless nickel/immersion gold pad finish. In the former case, Ni can only diffuse into the intermetallic compound from the solder matrix, while in the latter the Ni is only from the metallization layer on the Cu base. Scanning electron microscopy and transmission electron microscopy were employed to inspect the morphologies and interfacial microstructures of the intermetallic compounds. The thermal aging test was conducted to investigate their growth behavior under elevated temperature conditions. Mechanical strength after different aging hours was also evaluated via high speed ball pull test.

Effect of intermetallic compound layer thickness on the shear strength of 1206 chip resistor solder joint

2015 ◽  
Vol 27 (1) ◽  
pp. 52-58 ◽  
Author(s):  
Peter K. Bernasko ◽  
Sabuj Mallik ◽  
G. Takyi
Keyword(s):  
Shear Strength ◽  
Intermetallic Compound ◽  
Solder Joint ◽  
Layer Thickness ◽  
Solder Joints ◽  
Ageing Time ◽  
Circuit Board ◽  
Intermetallic Compound Layer ◽  
Content Type ◽  
Surface Mount

Purpose – The purpose of this paper is to study the effect of intermetallic compound (IMC) layer thickness on the shear strength of surface-mount component 1206 chip resistor solder joints. Design/methodology/approach – To evaluate the shear strength and IMC thickness of the 1206 chip resistor solder joints, the test vehicles were conventionally reflowed for 480 seconds at a peak temperature of 240°C at different isothermal ageing times of 100, 200 and 300 hours. A cross-sectional study was conducted on the reflowed and aged 1206 chip resistor solder joints. The shear strength of the solder joints aged at 100, 200 and 300 hours was measured using a shear tester (Dage-4000PXY bond tester). Findings – It was found that the growth of IMC layer thickness increases as the ageing time increases at a constant temperature of 175°C, which resulted in a reduction of solder joint strength due to its brittle nature. It was also found that the shear strength of the reflowed 1206 chip resistor solder joint was higher than the aged joints. Moreover, it was revealed that the shear strength of the 1206 resistor solder joints aged at 100, 200 and 300 hours was influenced by the ageing reaction times. The results also indicate that an increase in ageing time and temperature does not have much influence on the formation and growth of Kirkendall voids. Research limitations/implications – A proper correlation between shear strength and fracture mode is required. Practical implications – The IMC thickness can be used to predict the shear strength of the component/printed circuit board pad solder joint. Originality/value – The shear strength of the 1206 chip resistor solder joint is a function of ageing time and temperature (°C). Therefore, it is vital to consider the shear strength of the surface-mount chip component in high-temperature electronics.

scholarly journals Shear Strength and Aging Characteristics of Sn-3.0Ag-0.5Cu/Cu Solder Joint Reinforced with ZrO2 Nanoparticles

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1295
Author(s):  
Sri Harini Rajendran ◽  
Seung Jun Hwang ◽  
Jae Pil Jung
Keyword(s):  
Shear Strength ◽  
Solder Joint ◽  
Solder Joints ◽  
Solder Matrix ◽  
Fracture Analysis ◽  
Zro2 Nanoparticles ◽  
Solder Paste ◽  
Lap Shear ◽  
Matrix Fracture ◽  
The Matrix

This study investigates the shear strength and aging characteristics of Sn-3.0Ag-0.5Cu (SAC 305)/Cu joints by the addition of ZrO2 nanoparticles (NPs) having two different particle size: 5–15 nm (ZrO2A) and 70–90 nm (ZrO2B). Nanocomposite pastes were fabricated by mechanically mixing ZrO2 NPs and the solder paste. ZrO2 NPs decreased the β-Sn grain size and Ag3Sn intermetallic compound (IMC) in the matrix and reduced the Cu6Sn5 IMC thickness at the interface of lap shear SAC 305/Cu joints. The effect is pronounced for ZrO2A NPs added solder joint. The solder joints were isothermally aged at 175 °C for 24, 48, 144 and 256 h. NPs decreased the diffusion coefficient from 1.74 × 10–16 m/s to 3.83 × 10–17 m/s and 4.99 × 10–17 m/s for ZrO2A and ZrO2B NPs added SAC 305/Cu joints respectively. The shear strength of the solder joints decreased with the aging time due to an increase in the thickness of interfacial IMC and coarsening of Ag3Sn in the solder. However, higher shear strength exhibited by SAC 305-ZrO2A/Cu joints was attributed to the fine Ag3Sn IMC’s dispersed in the solder matrix. Fracture analysis of SAC 305-ZrO2A/Cu joints displayed mixed solder/IMC mode upon 256 h of aging.

Cracking of the Intermetallic Compound Layer in Solder Joints Under Drop Impact Loading

2011 ◽  
Vol 133 (3) ◽  
Author(s):  
Tong An ◽  
Fei Qin
Keyword(s):  
Intermetallic Compound ◽  
Solder Joint ◽  
Impact Loading ◽  
Driving Force ◽  
Solder Joints ◽  
Compound Layer ◽  
Drop Impact ◽  
Lead Free ◽  
Intermetallic Compound Layer ◽  
Crack Driving Force

The significant difference between failure modes of lead-containing and lead-free solder joints under drop impact loading remains to be not well understood. In this paper, we propose a feasible finite element approach to model the cracking behavior of solder joints under drop impact loading. In the approach, the intermetallic compound layer/solder bulk interface is modeled by the cohesive zone model, and the crack driving force in the intermetallic compound layer is evaluated by computing the energy release rate. The numerical simulation of a board level package under drop impact loading shows that, for the lead-containing Sn37Pb solder joint, the damage in the vicinity of the intermetallic compound layer initiates earlier and is much greater than that in the lead-free Sn3.5Ag solder joint. This damage relieves the stress in the intermetallic compound layer and reduces the crack driving force in it and consequently alleviates the risk of the intermetallic compound layer fracturing.

The size effect on intermetallic microstructure evolution of critical solder joints for flip chip assemblies

2015 ◽  
Vol 27 (4) ◽  
pp. 178-184 ◽  
Author(s):  
Ye Tian ◽  
Justin Chow ◽  
Xi Liu ◽  
Suresh K. Sitaraman
Keyword(s):  
Solder Joint ◽  
Design Methodology ◽  
Growth Process ◽  
Flip Chip ◽  
Solder Bump ◽  
Solder Joints ◽  
Solder Matrix ◽  
Industrial Practice ◽  
Content Type ◽  
Flip Chips

Purpose – The purpose of this paper is to study the intermetallic compound (IMC) thickness, composition and morphology in 100-μm pitch and 200-μm pitch Sn–Ag–Cu (SAC305) flip-chip assemblies after bump reflow and assembly reflow. In particular, emphasis is placed on the effect of solder joint size on the interfacial IMCs between metal pads and solder matrix. Design/methodology/approach – This work uses 100-μm pitch and 200-μm pitch silicon flip chips with nickel (Ni) pads and stand-off height of approximately 45 and 90 μm, respectively, assembled on substrates with copper (Cu) pads. The IMCs evolution in solder joints was investigated during reflow by using 100- and 200-μm pitch flip-chip assemblies. Findings – After bump reflow, the joints size controls the IMC composition and dominant IMC type as well as IMC thickness and also influences the dominant IMC morphology. After assembly reflow, the cross-reaction of the pad metallurgies promotes the dominant IMC transformation and shape coarsened on the Ni pad interface for smaller joints and promotes a great number of new dominate IMC growth on the Ni pad interface in larger joints. On the Cu pad interface, many small voids formed in the IMC in larger joints, but were not observed in smaller joints, combined with the drawing of the IMC growth process. Originality/value – With continued advances in microelectronics, it is anticipated that next-generation microelectronic assemblies will require a reduction of the flip-chip solder bump pitch to 100 μm or less from the current industrial practice of 130 to150 μm. This work shows that as the packaging size reduced with the solder joint interconnection, the solder size becomes an important factor in the intermetallic composition as well as morphology and thickness after reflow.

Effect of Immersion Coating Deposition Time on Solder Joint Properties

2016 ◽  
Vol 1133 ◽  
pp. 361-365
Author(s):  
Zetty Akhtar Abd Malek ◽  
Hardinna Wirda Kahar ◽  
Siti Rabiatull Aisha Idris ◽  
Mahadzir Ishak
Keyword(s):  
Intermetallic Compound ◽  
Solder Joint ◽  
Cross Sections ◽  
Surface Finish ◽  
Deposition Time ◽  
Industrial Area ◽  
Optical Microscope ◽  
Influential Factor ◽  
Surface Finishes ◽  
Immersion Plating

Surface finishes on copper pads have been known to be one of influential factor in the solder joint quality. This due to the difference in interfacial reaction and intermetallic compound formation on solder pad was strongly influence by the type of surface finishes. Deposition times during immersion plating process on copper pads are important as the thickness of coating will decide several properties of surface finish, such as wettability during soldering process. Thus, this study aims to investigate the effect of deposition time of immersion gold coating on wettability of the surface finish and how it affect the formation of intermetallic compounds on solder joint. In this works, deposition time of copper pads in immersion gold solution were varied from 3 minutes up to 15 minutes. The thickness of immersion gold layer that form on Cu pads were then measured using Scanning Electron Microscopy (SEM). As the main objective of this study is to study the effect of deposition time during immersion plating process towards solder joint, the pads were reflowed along with Sn-3.0Ag-0.5Cu solder in furnace under temperature 250 °C for 25 minutes. Then, the cross sections of the solder joints were examined using optical microscope in order to measure the wetting angle and thickness of intermetallic compound formed; which acceptable value in industrial area, should be below 40 ̊ and below 4μm as reflow respectively.

Sign in / Sign up

Export Citation Format

Share Document