scholarly journals Water uptake in epoxy matrix with voids: Experiments and modeling

2018 ◽  
Vol 53 (8) ◽  
pp. 1049-1065 ◽  
Author(s):  
F Abdelmola ◽  
LA Carlsson
Keyword(s):  
Epoxy Matrix ◽  
Moisture Diffusivity ◽  
Mechanical Analysis ◽  
Langmuir Model ◽  
Void Content ◽  
Moisture Uptake ◽  
Scanning Calorimetry ◽  
Rate Of Absorption ◽  
Void Geometry ◽  
Density Methods

The influence of voids on the moisture uptake of epoxy matrix has been studied. Specimens with void contents from 0 to about 50% were prepared. Void geometry and content were analyzed using microscopy and density methods. Void-containing samples were characterized by differential scanning calorimetry and dynamic mechanical analysis which verified consistency of chemistry. The moisture uptake of specimens immersed in distilled water at 40℃ was monitored. The rate of absorption and saturation moisture content increased with increasing void content. Mass balance calculations revealed that only 6–8% of the void volume is occupied by water at saturation. The moisture uptake of void-free and void-containing specimens was non-Fickian. The Langmuir model provided better fits to the experimental results, although the high void content specimens showed substantial deviations from the Langmuir diffusion model. The moisture diffusivity of the void-free and void-containing specimens agreed reasonably with the Maxwell inclusion model.

Processing and Characterization of Novel Bismaleimide-Based Shape Memory Polymer Composites

2012 ◽  
Author(s):  
G. P. Tandon ◽  
T. Gibson ◽  
J. Shumaker ◽  
R. Coomer ◽  
J. Baur ◽  
...  
Keyword(s):  
Shape Memory ◽  
Shape Memory Polymer ◽  
Cure Kinetics ◽  
Mechanical Analysis ◽  
Void Content ◽  
Variable Cross ◽  
Scanning Calorimetry ◽  
Cure Reaction ◽  
Expansion System ◽  
Memory Cycle

In the present study, a series of novel linear polyaspartimide-based silane endcapped (cross-linked) polymers are synthesized using 4-4′ bismaleimidodiphenylmethane, Jeffamine D-400 (BMI-JA-400), and (3-Aminopropyl) trimethoxysilane. To add strength to these systems, the trimethoxysilane moiety is cross-linked with the addition of water to create a thermosetting material with both improved toughness and variable cross-link densities. Thermal analysis is done to evaluate the developed shape-memory polymer (SMP) resin for composite processing feasibility. The solvent content in the resin and thermal stability is monitored using thermogravimetric analysis (TGA) while advanced rheometric expansion system (ARES) with parallel plate geometry is used to measure viscosity variation with temperature. The resin BMI-JA-400-Si-70/30 is chosen for making the composite based on its viscosity, weight change, and kinetic results. Differential scanning calorimetry (DSC) is performed to determine the cure kinetics including the temperatures at which the cure reaction initiates and completes in order to develop the cure cycle for composite fabrication. The selected SMP resin is hand-impregnated with T-300 plain-weave and T-700 uni-weave carbon fabric. Six-ply composites are successfully fabricated with < 2% void content using both fabric weaves. The thermo-mechanical properties of the SMP resin are measured using dynamic mechanical analysis (DMA). In addition, the shape memory cycle with free recovery is conducted on the SMP resin and composites.

Light-cured dental composites characterization by Electron Microscopy

1990 ◽  
Vol 48 (4) ◽  
pp. 428-429
Author(s):  
B. M. Culbertson ◽  
M. L. Devinev ◽  
E. C. Kao
Keyword(s):  
Electron Microscopy ◽  
Mechanical Analysis ◽  
Service Performance ◽  
Dental Composite ◽  
Dental Composites ◽  
Neat Resin ◽  
Scanning Calorimetry ◽  
Research Meeting ◽  
Formulation Variables

The service performance of current dental composite materials, such as anterior and posterior restoratives and/or veneer cements, needs to be improved. As part of a comprehensive effort to find ways to improve such materials, we have launched a broad spectrum study of the physicochemical and mechanical properties of photopolymerizable or visible light cured (VLC) dental composites. The commercially available VLC materials being studied are shown in Table 1. A generic or neat resin VLC system is also being characterized by SEM and TEM, to more fully understand formulation variables and their effects on properties.At a recent dental research meeting, we reported on the differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) characterization of the materials in Table 1. It was shown by DSC and DMA that the materials are substantially undercured by commonly used VLC techniques. Post curing in an oral cavity or a dry environment at 37 to 50°C for 7 or more hours substantially enhances the cure of the materials.

Star-shaped arylacetylene resins derived from silicon

2020 ◽  
Vol 40 (8) ◽  
pp. 676-684
Author(s):  
Niping Dai ◽  
Junkun Tang ◽  
Manping Ma ◽  
Xiaotian Liu ◽  
Chuan Li ◽  
...  
Keyword(s):  
High Performance ◽  
Room Temperature ◽  
Mechanical Test ◽  
Flexural Modulus ◽  
Mechanical Analysis ◽  
Reinforced Composites ◽  
Scanning Calorimetry ◽  
Chemical Structures ◽  
Structures And Properties ◽  
High Performance Resin

AbstractStar-shaped arylacetylene resins, tris(3-ethynyl-phenylethynyl)methylsilane, tris(3-ethynyl-phenylethynyl) phenylsilane, and tris (3-ethynyl-phenylethynyl) silane (TEPHS), were synthesized through Grignard reaction between 1,3-diethynylbenzene and three types of trichlorinated silanes. The chemical structures and properties of the resins were characterized by means of nuclear magnetic resonance, fourier-transform infrared spectroscopy, Haake torque rheomoter, differential scanning calorimetry, dynamic mechanical analysis, mechanical test, and thermogravimetric analysis. The results show that the melt viscosity at 120 °C is lower than 150 mPa⋅s, and the processing windows are as wide as 60 °C for the resins. The resins cure at the temperature as low as 150 °C. The good processabilities make the resins to be suitable for resin transfer molding. The cured resins exhibit high flexural modulus and excellent heat-resistance. The flexural modulus of the cured TEPHS at room temperature arrives at as high as 10.9 GPa. Its temperature of 5% weight loss (Td5) is up to 697 °C in nitrogen. The resins show the potential for application in fiber-reinforced composites as high-performance resin in the field of aviation and aerospace.

scholarly journals Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1851
Author(s):  
Hye-Seon Park ◽  
Chang-Kook Hong
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Crystallization Behavior ◽  
Mechanical Analysis ◽  
X Ray Diffraction ◽  
Nucleation Agent ◽  
Scanning Calorimetry ◽  
Nucleation Sites ◽  
Wide Range ◽  
Degree Of Crystallization

Poly (l-lactic acid) (PLLA) is a promising biomedical polymer material with a wide range of applications. The diverse enantiomeric forms of PLLA provide great opportunities for thermal and mechanical enhancement through stereocomplex formation. The addition of poly (d-lactic acid) (PDLA) as a nucleation agent and the formation of stereocomplex crystallization (SC) have been proven to be an effective method to improve the crystallization and mechanical properties of the PLLA. In this study, PLLA was blended with different amounts of PDLA through a melt blending process and their properties were calculated. The effect of the PDLA on the crystallization behavior, thermal, and mechanical properties of PLLA were investigated systematically by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarized optical microscopy (POM), dynamic mechanical analysis (DMA), and tensile test. Based on our findings, SC formed easily when PDLA content was increased, and acts as nucleation sites. Both SC and homo crystals (HC) were observed in the PLLA/PDLA blends. As the content of PDLA increased, the degree of crystallization increased, and the mechanical strength also increased.

scholarly journals Study on Structure, Thermal Behavior, and Viscoelastic Properties of Nanodiamond-Reinforced Poly (vinyl alcohol) Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1426
Author(s):  
Tomáš Remiš ◽  
Petr Bělský ◽  
Tomáš Kovářík ◽  
Jaroslav Kadlec ◽  
Mina Ghafouri Azar ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Analysis ◽  
Single Step ◽  
Poly Vinyl Alcohol ◽  
Scanning Calorimetry ◽  
X Ray Scattering ◽  
Transmission Electron ◽  
Primary Particles ◽  
Solution Casting Method ◽  
Average Size

In this work, advanced polymer nanocomposites comprising of polyvinyl alcohol (PVA) and nanodiamonds (NDs) were developed using a single-step solution-casting method. The properties of the prepared PVA/NDs nanocomposites were investigated using Raman spectroscopy, small- and wide-angle X-ray scattering (SAXS/WAXS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). It was revealed that the tensile strength improved dramatically with increasing ND content in the PVA matrix, suggesting a strong interaction between the NDs and the PVA. SEM, TEM, and SAXS showed that NDs were present in the form of agglomerates with an average size of ~60 nm with primary particles of diameter ~5 nm. These results showed that NDs could act as a good nanofiller for PVA in terms of improving its stability and mechanical properties.

scholarly journals Combined thermal analysis of plant oils

2021 ◽  
Author(s):  
Kinga Tamási ◽  
Kálmán Marossy
Keyword(s):  
Thermal Analysis ◽  
Differential Scanning Calorimetry ◽  
Low Temperature ◽  
Glassy State ◽  
Mechanical Analysis ◽  
Plant Oils ◽  
Scanning Calorimetry ◽  
Natural Plant ◽  
The Moment ◽  
Current Reversal

AbstractThe paper deals with the study of seven selected natural plant oils. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and thermally stimulated discharge (TSD) methods were used. It has been found that most of the oils tested are in a glassy state at low temperature and have multiple transitions in the low temperature range. DSC shows complex melting-like processes or glass transition. For both DMA and TSD, the scaffold supportive method was used and found as a suitable one. DMA and TSD proved more sensitive than DSC and revealed at least two transitions between − 120 and − 40 °C. In the case of three oils (argan, avocado and sunflower), current reversal was observed by TSD; this symptom cannot be fully explained at the moment.

scholarly journals Effects of Ni Additions on the High Temperature Expansion, Melting and Oxidation Behaviors of Cobalt-Based Superalloys

Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 173
Author(s):  
Patrice Berthod ◽  
Lionel Aranda ◽  
Jean-Paul Gomis
Keyword(s):  
Thermal Expansion ◽  
High Temperature ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Beneficial Effects ◽  
Ni Addition ◽  
High Temperature Expansion ◽  
High Fraction ◽  
Thermal Analysis Techniques ◽  
Ni Additions

Nickel is often added to cobalt-based superalloys to stabilize their austenitic structure. In this work the effects of Ni on several high temperature properties of a chromium-rich cobalt-based alloy reinforced by high fraction of TaC carbides are investigated. Different thermal analysis techniques are used: differential scanning calorimetry (DSC), thermo-mechanical analysis (TMA) and thermogravimetry (TG). Results show that the progressive addition of nickel did not induce great modifications of microstructure, refractoriness or thermal expansion. However, minor beneficial effects were noted, including reduction of the melting temperature range and slight decrease in thermal expansion coefficient. The most important improvement induced by Ni addition concerns the hot oxidation behavior. In this way, introducing several tens wt % Ni in this type of cobalt-based alloy may be recommended.

scholarly journals Preparation, Thermal, and Thermo-Mechanical Characterization of Polymeric Blends Based on Di(meth)acrylate Monomers

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 878
Author(s):  
Krystyna Wnuczek ◽  
Andrzej Puszka ◽  
Łukasz Klapiszewski ◽  
Beata Podkościelna
Keyword(s):  
Mechanical Analysis ◽  
Attenuated Total Reflection ◽  
Scanning Calorimetry ◽  
Force Microscopy ◽  
Chemical Structures ◽  
Atomic Force ◽  
Polymeric Blends ◽  
Ft Ir ◽  
Acrylate Monomers ◽  
Synthesized Materials

This study presents the preparation and the thermo-mechanical characteristics of polymeric blends based on di(meth)acrylates monomers. Bisphenol A glycerolate diacrylate (BPA.GDA) or ethylene glycol dimethacrylate (EGDMA) were used as crosslinking monomers. Methyl methacrylate (MMA) was used as an active solvent in both copolymerization approaches. Commercial polycarbonate (PC) was used as a modifying soluble additive. The preparation of blends and method of polymerization by using UV initiator (Irqacure® 651) was proposed. Two parallel sets of MMA-based materials were obtained. The first included more harmless linear hydrocarbons (EGDMA + MMA), whereas the second included the usually used aromatic copolymers (BPA.GDA + MMA). The influence of different amounts of PC on the physicochemical properties was discussed in detail. Chemical structures of the copolymers were confirmed by attenuated total reflection–Fourier transform infrared (ATR/FT-IR) spectroscopy. Thermo-mechanical properties of the synthesized materials were investigated by means of differential scanning calorimetry (DSC), thermogravimetric (TG/DTG) analyses, and dynamic mechanical analysis (DMA). The hardness of the obtained materials was also tested. In order to evaluate the surface of the materials, their images were obtained with the use of atomic force microscopy (AFM).

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

scholarly journals Preparation and Characterization of Talc Filled Thermoplastic Polyurethane/Polypropylene Blends

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Emi Govorčin Bajsić ◽  
Vesna Rek ◽  
Ivana Ćosić
Keyword(s):  
Thermal Properties ◽  
Thermoplastic Polyurethane ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Polypropylene Blends ◽  
Pp Blends ◽  
The Degree Of Crystallinity ◽  
Better Than

The effect of the addition of talc on the morphology and thermal properties of blends of thermoplastic polyurethane (TPU) and polypropylene (PP) was investigated. The blends of TPU and PP are incompatible because of large differences in polarities between the nonpolar crystalline PP and polar TPU and high interfacial tensions. The interaction between TPU and PP can be improved by using talc as reinforcing filler. The morphology was observed by means of scanning electron microscopy (SEM). The thermal properties of the neat polymers and unfilled and talc filled TPU/PP blends were studied by using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The addition of talc in TPU/PP blends improved miscibility in all investigated TPU/T/PP blends. The DSC results for talc filled TPU/PP blends show that the degree of crystallinity increased, which is due to the nucleating effect induced by talc particles. The reason for the increased storage modulus of blends with the incorporation of talc is due to the improved interface between polymers and filler. According to TGA results, the addition of talc enhanced thermal stability. The homogeneity of the talc filled TPU/PP blends is better than unfilled TPU/PP blends.

Sign in / Sign up

Export Citation Format

Share Document