Interaction force between magnetic field and ferromagnetic target: analytical, numerical and experimental study

SIMULATION ◽  
2018 ◽  
Vol 95 (3) ◽  
pp. 209-218
Author(s):  
Paolo Neri
Keyword(s):  
Magnetic Field ◽  
Ferromagnetic Material ◽  
Interaction Force ◽  
Experimental Results ◽  
Fe Model ◽  
Operational Conditions ◽  
Double Curvature ◽  
Magnetic Action ◽  
Parallel Surfaces ◽  
Vibration Tests

In this study, an analytical model and a finite element (FE) model were developed in order to study the force produced by a permanent magnet on a ferromagnetic target. The study was aimed at estimating the magnetic action in order to design an excitation device for vibration tests. The dynamic analysis of rotating structures as compressors’ bladed wheels requires a solicitation that reflects the operational conditions. If the component is made of ferromagnetic material, it is possible to use magnetic fields for the excitation. The present paper reports the interaction between planar parallel surfaces, first studied analytically and numerically, and the results were compared with experimental results. Then the interaction between sloping surfaces was analyzed, allowing an analytical boundary loss model to be developed. Finally, the FE model was improved to study the interaction between double curvature surfaces. A comparison with experimental results measured on an actual bladed wheel was performed.

Vibration Suppression Device Having Variable Inertia Mass by MR-Fluid

2011 ◽  
Author(s):  
Taichi Matsuoka
Keyword(s):  
Magnetic Field ◽  
Magnetic Particles ◽  
Vibration Suppression ◽  
Experimental Results ◽  
Inertia Force ◽  
Test Device ◽  
Piston Cylinder ◽  
New Type ◽  
Vibration Tests ◽  
Force Characteristics

Authors have proposed a new type of vibration suppression device that utilizes variable inertia mass by fluid which acts as a series inertia mass. The series inertia mass is proportional to not only square of a ratio between a diameter of a piston cylinder and a by-pass pipe, and also a density of the fluid. The resisting force characteristics in case of water or turbine oil were measured. To confirm the proposed theory and investigate effects of vibration control, vibration tests of frequency response and seismic response of one-degree-of-freedom system with the test device were carried out. The experimental results were compared with the calculated results, and the effects of vibration suppression are confirmed experimentally and theoretically. In this paper, in order to derive the effect of a variable inertia mass by using a magnet-rheological fluid, resisting force characteristics of the test device are measured in several cases of magnetic field. The orifice of the by-pass pipe can be changed in virtual, since some rare-earth magnets are installed around the by-pass pipe. It can be seen from experimental results that the inertia force is increasing as stronger magnetic fields. It is pointed out that the variable inertia mass can be derived since clustered magnetic particles in the by-pass pipe act as a virtual orifice under strong magnetic field. The relation between magnetic flux and variable inertia mass are estimated experimentally.

scholarly journals A parametric prediction of the Young’s modulus of polymers enhanced with ΜWCNTs

2018 ◽  
Vol 233 ◽  
pp. 00025
Author(s):  
P.V. Polydoropoulou ◽  
K.I. Tserpes ◽  
Sp.G. Pantelakis ◽  
Ch.V. Katsiropoulos
Keyword(s):  
Young’S Modulus ◽  
Elastic Properties ◽  
Young's Modulus ◽  
Experimental Results ◽  
Scale Model ◽  
Fe Model ◽  
Multi Scale ◽  
Unit Cells ◽  
Random Dispersion

In this work a multi-scale model simulating the effect of the dispersion, the waviness as well as the agglomerations of MWCNTs on the Young’s modulus of a polymer enhanced with 0.4% MWCNTs (v/v) has been developed. Representative Unit Cells (RUCs) have been employed for the determination of the homogenized elastic properties of the MWCNT/polymer. The elastic properties computed by the RUCs were assigned to the Finite Element (FE) model of a tension specimen which was used to predict the Young’s modulus of the enhanced material. Furthermore, a comparison with experimental results obtained by tensile testing according to ASTM 638 has been made. The results show a remarkable decrease of the Young’s modulus for the polymer enhanced with aligned MWCNTs due to the increase of the CNT agglomerations. On the other hand, slight differences on the Young’s modulus have been observed for the material enhanced with randomly-oriented MWCNTs by the increase of the MWCNTs agglomerations, which might be attributed to the low concentration of the MWCNTs into the polymer. Moreover, the increase of the MWCNTs waviness led to a significant decrease of the Young’s modulus of the polymer enhanced with aligned MWCNTs. The experimental results in terms of the Young’s modulus are predicted well by assuming a random dispersion of MWCNTs into the polymer.

scholarly journals Ambient Vibration Tests of an Arch Dam with Different Reservoir Water Levels: Experimental Results and Comparison with Finite Element Modelling

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Sergio Vincenzo Calcina ◽  
Laura Eltrudis ◽  
Luca Piroddi ◽  
Gaetano Ranieri
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Water Levels ◽  
Arch Dam ◽  
Experimental Results ◽  
Ambient Vibration ◽  
Reservoir Water ◽  
Ambient Vibration Tests ◽  
Vibration Properties ◽  
Vibration Tests

This paper deals with the ambient vibration tests performed in an arch dam in two different working conditions in order to assess the effect produced by two different reservoir water levels on the structural vibration properties. The study consists of an experimental part and a numerical part. The experimental tests were carried out in two different periods of the year, at the beginning of autumn (October 2012) and at the end of winter (March 2013), respectively. The measurements were performed using a fast technique based on asynchronous records of microtremor time-series. In-contact single-station measurements were done by means of one single high resolution triaxial tromometer and two low-frequency seismometers, placed in different points of the structure. The Standard Spectral Ratio method has been used to evaluate the natural frequencies of vibration of the structure. A 3D finite element model of the arch dam-reservoir-foundation system has been developed to verify analytically determined vibration properties, such as natural frequencies and mode shapes, and their changes linked to water level with the experimental results.

Design and Fabrication of a Magnetocaloric Microcooler

2005 ◽  
Author(s):  
Sangchae Kim ◽  
Bharath Bethala ◽  
Simone Ghirlanda ◽  
Senthil N. Sambandam ◽  
Shekhar Bhansali
Keyword(s):  
Magnetic Field ◽  
Ambient Temperature ◽  
Temperature Change ◽  
Entropy Change ◽  
Temperature Sensors ◽  
Experimental Results ◽  
Maximum Temperature ◽  
Alternative Technology ◽  
Temperature Conditions ◽  
Si Wafer

Magnetocaloric refrigeration is increasingly being explored as an alternative technology for cooling. This paper presents the design and fabrication of a micromachined magnetocaloric cooler. The cooler consists of fluidic microchannels (in a Si wafer), diffused temperature sensors, and a Gd5(Si2Ge2) magnetocaloric refrigeration element. A magnetic field of 1.5 T is applied using an electromagnet to change the entropy of the magnetocaloric element for different ambient temperature conditions ranging from 258 K to 280 K, and the results are discussed. The tests show a maximum temperature change of 7 K on the magnetocaloric element at 258 K. The experimental results co-relate well with the entropy change of the material.

Experimental Study of Magnetic Field Variation Induced in Ferromagnetic Materials

2013 ◽  
Vol 312 ◽  
pp. 402-405
Author(s):  
Yang Yong ◽  
Dong Sun ◽  
Jie Ji
Keyword(s):  
Magnetic Field ◽  
Plastic Region ◽  
Steel Specimen ◽  
Fatigue Tests ◽  
Experimental Results ◽  
Magnetic Memory ◽  
Field Variation ◽  
Magnetic Field Variation ◽  
Metal Magnetic Memory ◽  
Stress Increase

The fatigue tests on 15CrMo steel specimen were carried out and the metal magnetic memory (MMM) signals were detected. The experiment shows that the magnetic signals of specimen contain the information of stress distribution in the material inside. Furthermore, the experimental results show that the magnetic signals increase initial while then decrease slightly with the stress increase from 0kN to 200kN. Though analysis the MMM signals induced by different tensile stress within the plastic region of the specimen, a simple model was derived. The experimental results are consistent with the calculated results based on the Jiles-Atherton model.

Finite Element Study of the Cutting Mechanics of the Three Dimensional Rock Turning Process

2015 ◽  
Author(s):  
Demeng Che ◽  
Jacob Smith ◽  
Kornel F. Ehmann
Keyword(s):  
Finite Element ◽  
Oil And Gas ◽  
Three Dimensional ◽  
Polycrystalline Diamond ◽  
Close Correlation ◽  
Experimental Results ◽  
Failure Behavior ◽  
Fe Model ◽  
Gas Drilling ◽  
Cutting Mechanics

The unceasing improvements of polycrystalline diamond compact (PDC) cutters have pushed the limits of tool life and cutting efficiency in the oil and gas drilling industry. However, the still limited understanding of the cutting mechanics involved in rock cutting/drilling processes leads to unsatisfactory performance in the drilling of hard/abrasive rock formations. The Finite Element Method (FEM) holds the promise to advance the in-depth understanding of the interactions between rock and cutters. This paper presents a finite element (FE) model of three-dimensional face turning of rock representing one of the most frequent testing methods in the PDC cutter industry. The pressure-dependent Drucker-Prager plastic model with a plastic damage law was utilized to describe the elastic-plastic failure behavior of rock. A newly developed face turning testbed was introduced and utilized to provide experimental results for the calibration and validation of the formulated FE model. Force responses were compared between simulations and experiments. The relationship between process parameters and force responses and the mechanics of the process were discussed and a close correlation between numerical and experimental results was shown.

Experimental Research on the Magnetic Field Sensitive Polymeric Actuator

2011 ◽  
Vol 287-290 ◽  
pp. 603-607
Author(s):  
Chun Lin Xia ◽  
Yang Fang Wu ◽  
Qian Qian Lu
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Conversion ◽  
Experimental Research ◽  
Experimental Results ◽  
Deformation Characteristics ◽  
Analysis Software ◽  
Element Analysis ◽  
The Magnetic Field

Using domestic MFSP membrane as a medium of energy conversion, a kind of MFSP actuator was designed. The dedicated test equipment was constructed for experimental research, and the experimental results were given. The strip and circular MSFP membrane were analyzed qualitatively to obtain the deformation characteristics of membrane by finite element analysis software.

scholarly journals Elastic Properties of Magnetorheological Elastomers in a Heterogeneous Uniaxial Magnetic Field

2018 ◽  
Vol 19 (10) ◽  
pp. 3045 ◽  
Author(s):  
Takehito Kikuchi ◽  
Yusuke Kobayashi ◽  
Mika Kawai ◽  
Tetsu Mitsumata
Keyword(s):  
Magnetic Field ◽  
Elastic Properties ◽  
Uniform Magnetic Field ◽  
Large Strain ◽  
Small Strain ◽  
Experimental Results ◽  
The Other ◽  
Magnetorheological Elastomers ◽  
Other Hand ◽  
Strain Model

Magnetorheological elastomers (MREs) are stimulus-responsive soft materials that consist of polymeric matrices and magnetic particles. In this study, large-strain response of MREs with 5 vol % of carbonyl iron (CI) particles is experimentally characterized for two different conditions: (1) shear deformation in a uniform magnetic field; and (2), compression in a heterogeneous uniaxial magnetic field. For condition (1), dynamic viscoelastic measurements were performed using a rheometer with a rotor disc and an electric magnet that generated a uniform magnetic field on disc-like material samples. For condition (2), on the other hand, three permanent magnets with different surface flux densities were used to generate a heterogeneous uniaxial magnetic field under cylindrical material samples. The experimental results were mathematically modeled, and the relationship between them was investigated. We also used finite-element method (FEM) software to estimate the uniaxial distributions of the magnetic field in the analyzed MREs for condition (2), and developed mathematical models to describe these phenomena. By using these practicable techniques, we established a simple macroscale model of the elastic properties of MREs under simple compression. We estimated the elastic properties of MREs in the small-strain regime (neo–Hookean model) and in the large-strain regime (Mooney–Rivlin model). The small-strain model explains the experimental results for strains under 5%. On the other hand, the large-strain model explains the experimental results for strains above 10%.

Sign in / Sign up

Export Citation Format

Share Document