Enhancing thermal-moisture comfort of a chest wader with lining for fishermen

2016 ◽  
Vol 87 (17) ◽  
pp. 2133-2145
Author(s):  
Zheng Liu ◽  
Fengyuan Zou ◽  
Qing Zhan ◽  
Bugao Xu
Keyword(s):  
Relative Humidity ◽  
Moisture Absorption ◽  
Subjective Evaluation ◽  
Objective Evaluation ◽  
Working Environment ◽  
Hydraulic Pressure ◽  
Body Parts ◽  
Moisture Performance ◽  
The Common ◽  
Ease Allowance

As basic protective clothing, a chest wader needs to be worn by fishermen during wading work. Its thermal and moisture performance would directly influence fishermen’s comfort and health. In order to increase the thermal-moisture comfort for fishermen, this research aimed to design a new lining chest wader and to carry out both subjective and objective evaluations on its comfort properties. By simulating moisture absorption under a hydraulic pressure environment, we tested the water absorption and conductivity of the selected fabrics and water-absorbent resin materials, and used an appropriate combination of the fabric and the resin to cover different sweating areas of the human body. Ten subjects were recruited to conduct the wearing test on the chest wader to evaluate its thermal-moisture performance. The objective evaluation involved tracking the changes in temperature and relative humidity at four body parts when a participant wore the chest wader, while the subjective evaluation included a questionnaire about the wearing experience on the thermal-moisture comfort and operation convenience. The experimental results showed that the new lining enhanced the comfort significantly. Compared with the common chest wader, the new lining reduced the relative humidity of chest wader on average by 30% approximately, with the largest improvement being at the calf, followed by the thigh and crotch. The thermal-moisture performance of the chest wader was also influenced by the hydraulic pressure of the working environment and the ease allowance to the wearing body.

METHODOLOGY OF OBJECTIVE EVALUATION OF THE QUALITY BEARINGS BY VIBRO-ACOUSTICS AND ITS COMPARISON WITH A SUBJECTIVE METHOD

Akustika ◽  
2020 ◽  
pp. 58-66
Author(s):  
Stanislav Žiaran ◽  
Ondrej Chlebo ◽  
Ĺubomír Šooš
Keyword(s):  
Dynamic Load ◽  
Subjective Evaluation ◽  
Objective Evaluation ◽  
Living Environment ◽  
Working Environment ◽  
Subjective Method ◽  
Auditory Organ ◽  
Objective Methodology ◽  
Fft Analysis

The quality of bearing production has an impact not only on their reliability and lifetime, but also on the dynamic load of the working and living environment by excessive vibration and thus also noise. The intensity of the noise emitted by a bearing which is perceived by man characterizes the quality of its production. Reducing the dynamic load of mechanical systems and their components is reflected in the working environment by reducing noise emissions and immissions. The article proposes an objective method of bearing quality assessment based on measuring vibro-acoustic parameters of dynamic load of a new bearing using FFT analysis and the magnitude of the amplitude of bearing vibration acceleration and compares it with a subjective method that also uses the human auditory organ to assess bearing quality. The results of vibro-acoustic measurements were analysed in terms of vibration intensity and the noise of the produced bearings. The proposed objective methodology was compared with the subjective evaluation of the quality of bearings and the results of this methodology matched. The proposed methodology is applicable to all types of bearings, and it is possible to automate this methodology in the production process.

An Ergonomic Evaluation of the Effects of Veiling Reflection on the Human Visibility

2000 ◽  
Vol 44 (21) ◽  
pp. 3-501-3-501
Author(s):  
Jae-Min Park ◽  
Sang-Do Lee ◽  
Young-Sook Kim
Keyword(s):  
Information Search ◽  
Visual Information ◽  
Visual Target ◽  
Subjective Evaluation ◽  
Objective Evaluation ◽  
Luminance Contrast ◽  
Visual Sensitivity ◽  
Working Environment ◽  
Daily Newspapers ◽  
Human Sensibility

Man perceive and react around him through the five senses. Also man give rise to the human sensibility and maintain his emotion. This study doesn't limit working environment to VDT environment, but considers the universal working environment acquiring information by eyesight stimulation. In this respect, designed and made is experimental equipment such as an external light for veiling reflection, visual target suggesting system, and visual target considered luminance contrast level. And reading the visual target is selected as work after excerpting the editorials from daily newspapers in Korean and Chinese letter and making target for experimental condition. In case of forming an abnormal veiling reflection we consider the form; a vertical (25%, 50%, 75%)and a horizontal (25%, 50%, 75%). The results from the subjective evaluation are analyzed by SD (Semantic Differential) methodology of 5 point scale for visibility and nuisance when an abnormal veiling reflection forms on target. In addition, the results of the objective evaluation are suggested by measuring and analyzing EEG (Electroencephalogram) of bio-signal for visual sensitivity. The results of this study can apply to basic data which create a guideline of a visual operation. In particular, it can be designed as an illumination environment concerning an ergonomic factor on visual operations, mental stress such as a visual inspection operation, visual information search operation, etc. As a result, we can expect to reduce the visual nuisance and contribute to the improvement of the performance and the uplift of the competitive power.

Our Bodies, Whose Property?

2013 ◽  
Author(s):  
Anne Phillips
Keyword(s):  
Labor Markets ◽  
Personal Autonomy ◽  
The Body ◽  
Body Parts ◽  
Complex Issue ◽  
Human Organs ◽  
Property Owners ◽  
The Common ◽  
The Difference ◽  
The Right

No one wants to be treated like an object, regarded as an item of property, or put up for sale. Yet many people frame personal autonomy in terms of self-ownership, representing themselves as property owners with the right to do as they wish with their bodies. Others do not use the language of property, but are similarly insistent on the rights of free individuals to decide for themselves whether to engage in commercial transactions for sex, reproduction, or organ sales. Drawing on analyses of rape, surrogacy, and markets in human organs, this book challenges notions of freedom based on ownership of our bodies and argues against the normalization of markets in bodily services and parts. The book explores the risks associated with metaphors of property and the reasons why the commodification of the body remains problematic. The book asks what is wrong with thinking of oneself as the owner of one's body? What is wrong with making our bodies available for rent or sale? What, if anything, is the difference between markets in sex, reproduction, or human body parts, and the other markets we commonly applaud? The book contends that body markets occupy the outer edges of a continuum that is, in some way, a feature of all labor markets. But it also emphasizes that we all have bodies, and considers the implications of this otherwise banal fact for equality. Bodies remind us of shared vulnerability, alerting us to the common experience of living as embodied beings in the same world. Examining the complex issue of body exceptionalism, the book demonstrates that treating the body as property makes human equality harder to comprehend.

scholarly journals Objective Evaluation of Drivability in Passenger Cars with Dual-Clutch Transmission: A Case Study of Static Gearshift Condition

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Wei Zhou ◽  
Xuexun Guo ◽  
Xiaofei Pei ◽  
Chengcai Zhang ◽  
Jun Yan ◽  
...  
Keyword(s):  
Fuzzy Ahp ◽  
Subjective Evaluation ◽  
Objective Evaluation ◽  
Dual Clutch Transmission ◽  
Evaluation Tool ◽  
Passenger Cars ◽  
Denoising Method ◽  
Fuzzy Matrix ◽  
Predictability Score

This paper is aimed at the problem that the subjective drivability evaluation by experienced test drivers is limited in time efficiency and is of high cost and poor repeatability. In this article, an intelligent drivability objective evaluation tool (I-DOET) for passenger cars with dual-clutch transmission (DCT) is developed and verified by real vehicle testing. First, the signal denoising method and its key parameters, which are suitable for drivability evaluation, are selected based on analytic hierarchy process (AHP) and technique for order preference by similarity to ideal solution (TOPSIS). Besides, combined with the uncertainty characteristics of subjective judgment, a mathematical model of the objective drivability evaluation FARODE (fuzzy AHP-RS based on objective drivability evaluation) is proposed by using the fuzzy comprehensive assessment (FCA) method. The AHP and rough set (RS) method are used to calculate the subjective and objective weights of the drivability evaluation, respectively, and the proportion of subjective and objective weights is determined by the principle of minimum relative information entropy. The fuzzy matrix is built by membership function of the evaluation indexes. Finally, the static gearshift condition focused on by the subjective evaluation experts is taken as a case study. The predictability score is obtained by combining the drivability quantization lever vector, comprehensive weight, and fuzzy matrix. The experimental results indicate that the proposed method is applicable for objective drivability evaluation in passenger cars with DCT.

scholarly journals Subjective Product Evaluation System Based on Kansei Engineering and Analytic Hierarchy Process

Symmetry ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1340 ◽  
Author(s):  
Yaxue Zuo ◽  
Zhenya Wang
Keyword(s):  
Evaluation System ◽  
Comprehensive Evaluation ◽  
Subjective Evaluation ◽  
Reliability And Validity ◽  
Objective Evaluation ◽  
Product Evaluation ◽  
Kansei Engineering ◽  
Analytic Hierarchy ◽  
Evaluation Indexes ◽  
Hierarchy Process

Product evaluation is very important for product improvement and development, and subjective product evaluation determines customer’s evaluation of products to some extent, so the purpose of this study is to establish a reasonable subjective product evaluation system. In this study, we comprehensively determine the evaluation indexes based on Kansei engineering (KE), establish an overall product evaluation system by using analytic hierarchy process (AHP), and establish the subjective product evaluation system by classifying the evaluation indexes in the overall product evaluation system into “objective evaluation index” and “subjective evaluation index”, removing the objective evaluation indexes, and retaining the subjective evaluation indexes. Additionally, we select some modern chairs as experimental samples to verify the reliability and validity of this subjective product evaluation system by means of questionnaires. The experimental results show that, in this subjective product evaluation system, the subjective evaluation of the product is positively correlated with the “favorite” level of the product in comprehensive evaluation, and negatively correlated with the “least favorite” level of the product in comprehensive evaluation, indicating that this subjective product evaluation system realizes a symmetry between subjective product evaluation and comprehensive product evaluation. Therefore, it can be concluded that this subjective product evaluation system based on KE and AHP proposed in this study has reliability and validity, and can be used for product evaluation to judge the popularity of products and enhance the competitiveness of products.

scholarly journals The Impact of Urban Recreation Environment on Residents’ Happiness—Based on a Case Study in China

2021 ◽  
Vol 13 (10) ◽  
pp. 5549
Author(s):  
Lei Kang ◽  
Zhaoping Yang ◽  
Fang Han
Keyword(s):  
Low Income ◽  
Subjective Evaluation ◽  
Objective Evaluation ◽  
Income Group ◽  
High Income Group ◽  
Rapid Urbanization ◽  
Indirect Impact ◽  
Negative Effect ◽  
The Impact ◽  
Urban Recreation

Rapid urbanization promotes the expansion of urban tourism and recreation functions, but it also brings many problems, which affect residents’ happiness. Previous studies have emphasized the direct impact of urban recreation environment on happiness, and few have explored the indirect impact of urban recreation environment on happiness through subjective evaluation. Based on the survey data of nearly 10,000 permanent residents in 40 key tourism cities in China, this paper establishes a theoretical framework of the direct and indirect impact of urban recreation environment on happiness. The objective evaluation of natural recreation environment and sociocultural recreation environment has an important influence on happiness, but the influence of natural recreation environment is greater than that of sociocultural recreation environment. Individual subjective satisfaction with urban recreation environment mediates the relationship between urban objective environment and happiness. Urban parks have a positive effect on happiness, while tourist attractions have a negative effect. The influence of urban location on happiness is nonlinear. The high-income group is more sensitive to the recreation environment, while the low-income group is less sensitive to the recreation environment. These findings provide insights for further improving citizens’ quality of life and designing urban construction in developing countries under the conditions of rapid urbanization.

scholarly journals Annoyance evaluation of noise emitted by urban substation

2021 ◽  
pp. 146134842110143
Author(s):  
Li Jun ◽  
Li Li ◽  
Zhang Yongxiang ◽  
Chu Zhigang ◽  
Fan Xiaopeng
Keyword(s):  
Regression Model ◽  
Urban Areas ◽  
Subjective Evaluation ◽  
Noise Pollution ◽  
Objective Evaluation ◽  
Semantic Differential ◽  
Differential Method ◽  
Practical Application ◽  
Noise Evaluation ◽  
Objective And Subjective Evaluation

In China, noise pollution from substations in urban areas is becoming more and more serious. An annoyance evaluation of the noise emitted by urban substations is presented. First, the subjective evaluation is conducted on the noise samples from urban substations via the semantic differential method. Subsequently, according to the typical characteristics of urban substation noise, 14 acoustical metrics are used to describe the noise samples for objective evaluation. Then the correlation analysis and regression analysis between the objective and subjective evaluation results are carried out. Finally, a regression model for urban substation noise evaluation is established. Practical application shows that the regression model can correctly predict the subjective annoyance of urban substation noise.

A comparison of hygrothermal simulation results derived from four simulation tools

2021 ◽  
pp. 174425912098876
Author(s):  
Maurice Defo ◽  
Michael Lacasse ◽  
Abdelaziz Laouadi
Keyword(s):  
Relative Humidity ◽  
Outer Layer ◽  
Growth Index ◽  
Mould Growth ◽  
Simulation Tools ◽  
Assembly Design ◽  
Hygrothermal Simulation ◽  
Moisture Performance ◽  
Wood Frame ◽  
Wall Assembly

The objective of this work was to compare the hygrothermal responses and the moisture performance of four wood-frame walls as predicted by four hygrothermal (HAM) simulation tools, namely: DELPHIN, WUFI, hygIRC and COMSOL. The four wall systems differ only in their cladding type; these were fibreboard, vinyl, stucco and brick. Three Canadian cities having different climates were selected for simulations: Ottawa, Ontario; Vancouver, British Columbia and Calgary, Alberta. In each city, simulations were run for 2 years. Temperature and relative humidity of the outer layer of OSB sheathing were compared amongst the four simulation tools. The mould growth index on the outer layer of the OSB sheathing was used to compare the moisture performance predicted by the respective hygrothermal simulation tools. Temperature profiles of the outer layer of the OSB sheathing were all in good agreement for the four HAM tools in the three locations. For relative humidity, the highest discrepancies amongst the four tools were found with stucco cladding where differences as high as 20% could be found from time to time. Mould growth indices predicted by the four HAM tools were similar in some cases but different in other cases. The discrepancies amongst the different HAM tools were likely related to: the material property processing, how the quantity of wind-driven rain absorbed at the cladding surface is computed and some implementation details. Despite these discrepancies, The tools generally yielded consistent results and could be used for comparing the impacts of different designs on the risk of premature deterioration, as well as for evaluating the relative effects of climate change on a given wall assembly design.

scholarly journals Breast softness in patients randomised to postmastectomy breast reconstruction with an expander prosthesis or DIEP flap

2021 ◽  
Author(s):  
Linda Tallroth ◽  
Håkan Brorson ◽  
Nathalie Mobargha ◽  
Patrik Velander ◽  
Stina Klasson ◽  
...  
Keyword(s):  
Breast Reconstruction ◽  
Subjective Evaluation ◽  
Objective Evaluation ◽  
Applanation Tonometry ◽  
Diep Flap ◽  
Level Of Evidence ◽  
Patient Reported ◽  
Delayed Breast Reconstruction ◽  
Level I ◽  
Therapeutic Study

Abstract Background Objectively measured breast softness in reconstructed breasts and its relation to patients’ subjective satisfaction with breast softness has not yet been investigated. The aim of this study was to evaluate breast softness in patients 1 year following delayed breast reconstruction with an expander prosthesis (EP) or deep inferior epigastric perforator (DIEP) flap, using objective and subjective methods. Methods Seventy-three patients were randomised to breast reconstruction with an EP or DIEP flap between 2012 and 2018. Of these, 69 completed objective evaluation at a mean of 25 (standard deviation, SD 9.4) months following breast reconstruction. Objective evaluation included measurements of breast volume, jugulum-nipple distance, clavicular-submammary fold distance, ptosis and Baker scale grading. Breast softness was assessed with applanation tonometry. Subjective evaluation was performed using the BREAST-Q questionnaire. Results Objectively, DIEP flaps were significantly softer than EP breast reconstructions. Non-operated contralateral breasts were significantly softer compared with reconstructed breasts. In the subjective evaluation, the median score on the question (labelled 1.h) “How satisfied or dissatisfied have you been with the softness of your reconstructed breast (s)?” was higher in the DIEP flap group corresponding to greater satisfaction in this group. A fair correlation was found between the applanation tonometry and the patient-reported satisfaction with the reconstructed breast’s softness (rs = 0.37). Conclusions In terms of breast softness, breast reconstructions with DIEP flaps result in more satisfied patients. Concerning applanation tonometry as an objective tool for softness assessment, future studies on interobserver agreement are warranted. Level of evidence: Level I, therapeutic study

Slow rehydration improves the recovery of dried bacterial populations

1992 ◽  
Vol 38 (6) ◽  
pp. 520-525 ◽  
Author(s):  
J. W. Kosanke ◽  
R. M. Osburn ◽  
G. I. Shuppe ◽  
R. S. Smith
Keyword(s):  
Relative Humidity ◽  
Rhizobium Leguminosarum ◽  
Moisture Absorption ◽  
Rhizobium Meliloti ◽  
Bacterial Populations ◽  
Bulk Powder ◽  
Alfalfa Seed ◽  
Powder Samples ◽  
Cellular Stresses ◽  
Rhizobium Leguminosarum Biovar Trifolii

Slow rehydration of bacteria from dried inoculant formulations provided higher viable counts than did rapid rehydration. Estimates were higher when clay and peat powder formulations of Rhizobium meliloti, Rhizobium leguminosarum biovar trifolii, and Pseudomonas putida, with water activities between 0.280 and 0.650, were slowly rehydrated to water activities of approximately 0.992 before continuing the dilution plating sequence. Rhizobium meliloti populations averaged 6.8 × 108 cfu/g and 1328 cfu/alfalfa seed greater when slowly rehydrated from bulk powder and preinoculated seeds, respectively. Bulk powder samples were slowly rehydrated to 0.992 water activity by the gradual addition of diluent, followed by a 10-min period for moisture equilibration. Preinoculated seed samples were placed in an environmental chamber at 24 °C with relative humidity greater than 80% for 1 h to allow moisture absorption. "Upshock," osmotic cellular stresses that occur during rehydration, was reduced when dried microbial formulations were slowly rehydrated and equilibrated before becoming fully hydrated in the dilution plating sequence. These procedures may also be applicable when estimating total viable bacterial populations from dried soil or other dry formulations. Key words: rehydration procedure, microbial rehydration, desiccation, Rhizobium, Pseudomonas.

Sign in / Sign up

Export Citation Format

Share Document