Influence of polyurethane foam on chemical clogging of nonwoven geotextile and tailings caused by ferrous iron

2020 ◽  
pp. 004051752097345
Author(s):  
Sheng Liu ◽  
Yuan Wang ◽  
Di Feng

The chemical clogging of geotextiles filters is a common issue, which threatens the safety of engineering projects. To reduce the chemical clogging of nonwoven geotextiles and enhance their drainage capability, a polyurethane foam was innovatively placed under the nonwoven geotextiles in this paper. A series of column tests were conducted to study the mechanism of the polyurethane foam to reduce the chemical clogging of the nonwoven geotextile filters in tailings caused by ferrous iron. In addition, the influence of the concentration of Fe2+, hydraulic gradient and thickness of the tailings specimen on the chemical clogging of the polyurethane foam and nonwoven geotextiles was examined. Less chemical clogging of geotextiles caused by polyurethane foam was observed and the related mechanism was firstly explained. The polyurethane foam under the geotextile reduced the contact between the geotextile and air. As a result, the chemical clogging of the geotextile was alleviated, which increased the drainage capability of the geotextiles. A high water saturation of the polyurethane foam would help to a reduce the extent of the chemical clogging of the geotextile. The chemical clogging characteristics of geotextiles and polyurethane foam under different concentrations of Fe2+ and hydraulic gradients were observed.

1985 ◽  
Vol 25 (06) ◽  
pp. 945-953 ◽  
Author(s):  
Mark A. Miller ◽  
H.J. Ramey

Abstract Over the past 20 years, a number of studies have reported temperature effects on two-phase relative permeabilities in porous media. Some of the reported results, however, have been contradictory. Also, observed effects have not been explained in terms of fundamental properties known to govern two-phase flow. The purpose of this study was to attempt to isolate the fundamental properties affecting two-phase relative permeabilities at elevated temperatures. Laboratory dynamic-displacement relative permeability measurements were made on unconsolidated and consolidated sand cores with water and a refined white mineral oil. Experiments were run on 2-in. [5.1-cm] -diameter, 20-in. [52.-cm] -long cores from room temperature to 300F [149C]. Unlike previous researchers, we observed essentially no changes with temperature in either residual saturations or relative permeability relationships. We concluded that previous results may have been affected by viscous previous results may have been affected by viscous instabilities, capillary end effects, and/or difficulties in maintaining material balances. Introduction Interest in measuring relative permeabilities at elevated temperatures began in the 1960's with petroleum industry interest in thermal oil recovery. Early thermal oil recovery field operations (well heaters, steam injection, in-situ combustion) indicated oil flow rate increases far in excess of what was predicted by viscosity reductions resulting from heating. This suggested that temperature affects relative permeabilities. One of the early studies of temperature effects on relative permeabilities was presented by Edmondson, who performed dynamic displacement measurements with crude performed dynamic displacement measurements with crude and white oils and distilled water in Berea sandstone cores. Edmondson reported that residual oil saturations (ROS's) (at the end of 10 PV's of water injected) decreased with increasing temperature. Relative permeability ratios decreased with temperature at high water saturations but increased with temperature at low water saturations. A series of elevated-temperature, dynamic-displacement relative permeability measurements on clean quartz and "natural" unconsolidated sands were reported by Poston et al. Like Edmondson, Poston et al. reported a decrease in the "practical" ROS (at less than 1 % oil cut) as temperature increased. Poston et al. also reported an increase in irreducible water saturation. Although irreducible water saturations decreased with decreasing temperature, they did not revert to the original room temperature values. It was assumed that the cores became increasingly water-wet with an increase in both temperature and time; measured changes of the IFT and the contact angle with temperature increase, however, were not sufficient to explain observed effects. Davidson measured dynamic-displacement relative permeability ratios on a coarse sand and gravel core with permeability ratios on a coarse sand and gravel core with white oil displaced by distilled water, nitrogen, and superheated steam at temperatures up to 540F [282C]. Starting from irreducible water saturation, relative permeability ratio curves were similar to Edmondson's. permeability ratio curves were similar to Edmondson's. Starting from 100% oil saturation, however, the curves changed significantly only at low water saturations. A troublesome aspect of Davidson's work was that he used a hydrocarbon solvent to clean the core between experiments. No mention was made of any consideration of wettability changes, which could explain large increases in irreducible water saturations observed in some runs. Sinnokrot et al. followed Poston et al.'s suggestion of increasing water-wetness and performed water/oil capillary pressure measurements on consolidated sandstone and limestone cores from room temperature up to 325F [163C]. Sinnokrot et al confirmed that, for sandstones, irreducible water saturation appeared to increase with temperature. Capillary pressures increased with temperature, and the hysteresis between drainage and imbibition curves reduced to essentially zero at 300F [149C]. With limestone cores, however, irreducible water saturations remained constant with increase in temperature, as did capillary pressure curves. Weinbrandt et al. performed dynamic displacement experiments on small (0.24 to 0.49 cu in. [4 to 8 cm3] PV) consolidated Boise sandstone cores to 175F [75C] PV) consolidated Boise sandstone cores to 175F [75C] with distilled water and white oil. Oil relative permeabilities shifted toward high water saturations with permeabilities shifted toward high water saturations with increasing temperature, while water relative permeabilities exhibited little change. Weinbrandt et al. confirmed the findings of previous studies that irreducible water saturation increases and ROS decreases with increasing temperature. SPEJ P. 945


2021 ◽  
Author(s):  
Nasser Faisal Al-Khalifa ◽  
Mohammed Farouk Hassan ◽  
Deepak Joshi ◽  
Asheshwar Tiwary ◽  
Ihsan Taufik Pasaribu ◽  
...  

Abstract The Umm Gudair (UG) Field is a carbonate reservoir of West Kuwait with more than 57 years of production history. The average water cut of the field reached closed to 60 percent due to a long history of production and regulating drawdown in a different part of the field, consequentially undulating the current oil/water contact (COWC). As a result, there is high uncertainty of the current oil/water contact (COWC) that impacts the drilling strategy in the field. The typical approach used to develop the field in the lower part of carbonate is to drill deviated wells to original oil/water contact (OOWC) to know the saturation profile and later cement back up to above the high-water saturation zone and then perforate with standoff. This method has not shown encouraging results, and a high water cut presence remains. An innovative solution is required with a technology that can give a proactive approach while drilling to indicate approaching current oil/water contact and geo-stop drilling to give optimal standoff between the bit and the detected water contact (COWC). Recent development of electromagnetic (EM) look-ahead resistivity technology was considered and first implemented in the Umm Gudair (UG) Field. It is an electromagnetic-based signal that can detect the resistivity features ahead of the bit while drilling and enables proactive decisions to reduce drilling and geological or reservoir risks related to the well placement challenges.


2021 ◽  
Vol 2 ◽  
pp. 1-14
Author(s):  
Md Nahidul Hasan ◽  
Sally Potter-McIntyre ◽  
Steve Tedesco

The Kizler North Field in northwest Lyon County, Kansas, is a producing field with structures associated with both uplift of the Ancestral Rockies (Pennsylvanian to early Permian) and reactivation of structures along the Proterozoic midcontinent rift system (MRS), which contributed to the current complex and poorly understood play mechanisms. The Lower Paleozoic dolomitic Simpson Group, Viola Limestone, and “Hunton Group” are the reservoir units within the field. These units have significant vuggy porosity, which is excellent for field potential; however, in places, the reservoir is inhibited by high water saturation. The seismic data show that two late-stage wrench fault events reactivated existing faults. The observed wrench faults exhibit secondary P, R’, and R Riedel shears, which likely resulted from Central Kansas uplift-MRS wrenching. The latest stage event breached reservoir caprock units during post-Mississippian to pre-Desmoinesian time and allowed for hydrocarbon migration out of the reservoirs. Future exploration models of the Kizler North and analog fields should be based on four play concepts: 1) four-way closure with wrench-fault-related traps, 2) structural highs in the Simpson Group and Viola Limestone, 3) thick “Hunton Group,” and 4) presence of a wrench fault adjacent to the well location that generates subtle closure but not directly beneath it, which causes migration out of reservoirs. In settings where complex structural styles are overprinted, particular attention should be paid to the timing of events that may cause breaches of seals in some structures but not others. Mapping the precise location and vertical throw of the reactivated wrench faults using high-resolution seismic data can help reduce the drilling risk in analog systems.


Energies ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 3231
Author(s):  
Stian Almenningen ◽  
Per Fotland ◽  
Geir Ersland

This paper reports formation and dissociation patterns of methane hydrate in sandstone. Magnetic resonance imaging spatially resolved hydrate growth patterns and liberation of water during dissociation. A stacked core set-up using Bentheim sandstone with dual water saturation was designed to investigate the effect of initial water saturation on hydrate phase transitions. The growth of methane hydrate (P = 8.3 MPa, T = 1–3 °C) was more prominent in high water saturation regions and resulted in a heterogeneous hydrate saturation controlled by the initial water distribution. The change in transverse relaxation time constant, T2, was spatially mapped during growth and showed different response depending on the initial water saturation. T2 decreased significantly during growth in high water saturation regions and remained unchanged during growth in low water saturation regions. Pressure depletion from one end of the core induced a hydrate dissociation front starting at the depletion side and moving through the core as production continued. The final saturation of water after hydrate dissociation was more uniform than the initial water saturation, demonstrating the significant redistribution of water that will take place during methane gas production from a hydrate reservoir.


2020 ◽  
Vol 836 ◽  
pp. 124-130
Author(s):  
M.A. Marinin ◽  
V.V. Dolzhikov ◽  
V.A. Isheyskiy

The article discusses the experience of drilling and blasting operations in the conditions of high water cut of the rock massif, it also presents practical experience in modeling and forecasting water inflows into workings. By the example of the Koashvinskoe deposit, the problems of work in conditions of high water cut of the rock mass leading to the collapse and silting of drilled boreholes are considered. The article presents calculations showing the effectiveness of the drainage systems for lowering the groundwater level of a prepared rock mass section. The paper provides a rationale for the optimal mass of bottom charges for the preparation of drains in the rock mass, depending on the water saturation of the mass and the grid of drilled boreholes.


2020 ◽  
Vol 172 ◽  
pp. 15002
Author(s):  
Targo Kalamees ◽  
Simo Ilomets ◽  
Mattias Põldaru ◽  
Paul Klõseiko ◽  
Urve Kallavus ◽  
...  

Spray polyurethane foam (SPF) roofs are widely used in North America. Much fewer usage examples and experience can be found in Northern European cold climatic conditions. This study analyses hygrothermal performance and the reasons for the roof’s degradation and end of service life of an SPF and polyurea roof. The service life of the roof is over and major reconstruction is needed eight year after construction. The current study uses field measurements included onsite temperature and humidity measurements and extensive surveying, the roof was opened from several locations and test samples were taken for laboratory tests. The influence of UV radiation on the loss of adhesion was tested. Solar radiation quickly degraded the top surface of the in-situ sprayed polyurethane foam insulation causing a weak connection between the foam layers. Due to mechanically damaged and UV degraded polyurea roofing, water has leaked into the SPF. The water inside or below the foam evaporated during sunny days and broke the adhesion of different foam layers. Larger foam blisters were observed on the upper part of the insulation caused by high water vapour pressure. This is considered the most realistic cause of separation of the SPF layers. The analyse of hygrothermal performance, service life, and durability prediction should be included into the design process, especially for structures with small or without long term performance experience.


Geophysics ◽  
1998 ◽  
Vol 63 (1) ◽  
pp. 154-160 ◽  
Author(s):  
Thierry Cadoret ◽  
Gary Mavko ◽  
Bernard Zinszner

Extensional and torsional wave‐attenuation measurements are obtained at a sonic frequency around 1 kHz on partially saturated limestones using large resonant bars, 1 m long. To study the influence of the fluid distribution, we use two different saturation methods: drying and depressurization. When water saturation (Sw) is higher than 70%, the extensional wave attenuation is found to depend on whether the resonant bar is jacketed. This can be interpreted as the Biot‐Gardner‐White effect. The experimental results obtained on jacketed samples show that, during a drying experiment, extensional wave attenuation is influenced strongly by the fluid content when Sw is between approximately 60% and 100%. This sensitivity to fluid saturation vanishes when saturation is obtained through depressurization. Using a computer‐assisted tomographic (CT) scan, we found that, during depressurization, the fluid distribution is homogeneous at the millimetric scale at all saturations. In contrast, during drying, heterogeneous saturation was observed at high water‐saturation levels. Thus, we interpret the dependence of the extensional wave attenuation upon the saturation method as principally caused by a fluid distribution effect. Torsional attenuation shows no sensitivity to fluid saturation for Sw between 5% and 100%.


1970 ◽  
Vol 10 (04) ◽  
pp. 337-348 ◽  
Author(s):  
F.I. Stalkup

Abstract Displacements of laboratory oils by propane in long, consolidated sandstone cores in the presence of high water saturations have shown that oil recoveries approaching 100 percent may be realized by continuous water-propane injection, even for oil saturations close to residual oil. However, it was often necessary to inject many pore volumes of solvent to attain this high a recovery. Initial oil saturations were established by injecting water and oil at a constant ratio into the porous medium containing residual oil to a waterflood until a steady state was obtained. Propane and water were then injected in the same fixed ratio to displace the oil. These and other experiments indicate that in the presence of a high water saturation only part of the presence of a high water saturation only part of the oil is flowable. Part resides in locations that are blocked by water, and the oil in these stagnant locations is not flowable. This nonflowable oil, it is believed, can be recovered by molecular diffusion into the flowing propane of a water-propane displacement. Values for the saturation of hydrocarbon that is contained in the stagnant locations and values for the ratio of the longitudinal hydrodynamic-dispersion coefficient to displacement velocity were determined at various water saturations in the test sandstones. The data suggest that rock wettability may influence the stagnant saturation and that stagnant oil saturations may not be as large in reservoir rocks as they are observed to be in laboratory sandstones. Mass transfer between the flowing solvent and hydrocarbon components in the stagnant saturation was expressed by a first-order rate expression. Rough values for the mass transfer coefficients for the propane-trimethylhexane hydrocarbon pair were estimated from experiments. Computations using these values for mass transfer coefficients indicate that experiments in laboratory-size cores may show much poorer displacement efficiency than that which might actually occur in the field. Introduction Injection of water with light hydrocarbon solvents is a technique that may be used to partially control solvent mobility. The higher water saturation forced by water injection reduces the permeability to solvent flow, and the mobility of the solvent region is reduced relative to that of the oil-bank region. However, it also might be expected that this higher water saturation influences the microscopic unit displacement of oil by solvent to some degree. For example, as discussed by Thomas et al., two possible effects of high water saturation on the displacement mechanism come to mind. First, a miscible displacement in the presence of water is operating on a different pore-size distribution than if no water were present. Pore-size distribution and the dp term (product of the microscopic inhomogeneity factor and "effective" particle diameter) may considerably influence the magnitudes of transverse and longitudinal dispersion coefficients. Secondly, in a multiphase system the wetting phase may trap single pores or even isolate large fingers or dendrites of the nonwetting phase. The nonwetting phase in these dead-end pores or dendrites would be phase in these dead-end pores or dendrites would be nonflowing and might either be completely isolated by the wetting phase or might communicate with the flowing nonwetting fluid by diffusion through nonwetting fluid-filled pores. Aspects of miscible displacement in the presence of water have been investigated by a number of researchers. Fitzgerald and Nielson observed that the simultaneous injection of gasoline and water into a Berea sandstone core in a 1:2 ratio recovered only 36 percent of the Bradford crude oil left in the core after waterflooding, and that only 55 to 75 percent recoveries were obtained for simultaneous water-solvent injection into the core when it contained crude oil at connate water saturation. Moreover, these authors reported recoveries of only 60 to 80 percent when solvent alone was injected into the core to displace residual oil to a waterflood. Raimondi et al. injected ethyl benzene (oil) and water simultaneously into a Berea sandstone core to establish flowing oil and water saturations and then injected heptane (solvent) and water simultaneously into the core to miscibly displace the ethyl benzene. SPEJ p. 337


Sign in / Sign up

Export Citation Format

Share Document