Enhanced properties of the poly(propylene carbonate)/poly(butylene succinate) composites with chain extender

2018 ◽  
Vol 32 (8) ◽  
pp. 1068-1077 ◽  
Author(s):  
Jing Sun ◽  
Liangqiang Wei ◽  
Shanshan Luo ◽  
Anrong Huang ◽  
Min Shi
Keyword(s):  
Mechanical Properties ◽  
Thermal Decomposition ◽  
Tensile Strength ◽  
Propylene Carbonate ◽  
Mechanical Analysis ◽  
Chain Extender ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Enhanced Properties ◽  
Poly Propylene

Poly(propylene carbonate) (PPC) blended with poly(butylene succinate) (PBS) with chain extender (CE) was prepared by melt mixing. Mechanical properties of PPC/PBS composites showed that the addition of CE can increase its tensile strength and unnotched impact strength, and the PPC/PBS composites had higher tensile strength when CE (0.4 wt%) was added into PPC/PBS composites. Thermogravimetric measurements revealed that adding CE to PPC/PBS (70/30 wt%) can improve the thermal decomposition temperatures ( T −5% and T −10%). Dynamic mechanical analysis revealed that the incorporation of CE increased the storage modulus of the PPC/PBS (70/30 wt%) composites.

Poly(Butylene Succinate) Composites Reinforced with Short Sisal Fibres

2001 ◽  
Vol 9 (5) ◽  
pp. 333-338 ◽  
Author(s):  
Mitsuhiro Shibata ◽  
Retsu Makino ◽  
Ryutoku Yosomiya ◽  
Hiroyuku Takeishi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fibre Length ◽  
Mechanical Analysis ◽  
Fibre Content ◽  
Flexural Properties ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Sisal Fibre ◽  
The Matrix

Poly(butylene succinate) composites reinforced with short sisal fibre were prepared by melt mixing and subsequent injection moulding. The influence of fibre length, fibre content and the surface treatment of the natural fibres on the mechanical properties of the composites were evaluated. Regarding fibre length, the tensile and flexural properties of the composites had maxima at a fibre length of about 5 mm. The flexural and tensile moduli of the composites increased with increasing fibre content. Although the tensile strength hardly changed, the flexural strength increased up to a fibre content of 10 wt%. The dynamic mechanical analysis of the composites showed that the storage moduli at above ca.-16°C (corresponding to the glass transition temperature of the matrix) increased with increasing fibre content.

Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

scholarly journals Biodegradable and Toughened Composite of Poly(Propylene Carbonate)/Thermoplastic Polyurethane (PPC/TPU): Effect of Hydrogen Bonding

2018 ◽  
Vol 19 (7) ◽  
pp. 2032 ◽  
Author(s):  
Dongmei Han ◽  
Guiji Chen ◽  
Min Xiao ◽  
Shuanjin Wang ◽  
Shou Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Propylene Carbonate ◽  
Thermoplastic Polyurethane ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Thermal Stabilities ◽  
Dynamic Mechanical ◽  
Brittle Ductile Transition ◽  
Poly Propylene

The blends of Poly(propylene carbonate) (PPC) and polyester-based thermoplastic polyurethane (TPU) were melt compounded in an internal mixer. The compatibility, thermal behaviors, mechanical properties and toughening mechanism of the blends were investigated using Fourier transform infrared spectra (FTIR), tensile tests, impact tests, differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and dynamic mechanical analysis technologies. FTIR and SEM examination reveal strong interfacial adhesion between PPC matrix and suspended TPU particles. Dynamic mechanical analyzer (DMA) characterize the glass transition temperature, secondary motion and low temperature properties. By the incorporation of TPU, the thermal stabilities are greatly enhanced and the mechanical properties are obviously improved for the PPC/TPU blends. Moreover, PPC/TPU blends exhibit a brittle-ductile transition with the addition of 20 wt % TPU. It is considered that the enhanced toughness results in the shear yielding occurred in both PPC matrix and TPU particles of the blends.

The Research of Poly Propylene Carbonate /Nano-SiO2 Composites

2014 ◽  
Vol 904 ◽  
pp. 74-77 ◽  
Author(s):  
Qu Li ◽  
Heng Wu ◽  
Si Yuan Xie ◽  
Jiao Sun ◽  
Xing Hai Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Glass Transition ◽  
Transition Temperature ◽  
Propylene Carbonate ◽  
Tensile Tests ◽  
Slight Improvement ◽  
Biodegradable Poly ◽  
Poly Propylene

Biodegradable poly (propylene carbonate) (PPC) composite with a slight improvement in the thermal stability and tensile strength was successfully prepared by incorporating a low content of nano-SiO2. Tensile tests demonstrate the better mechanical properties of the composites prepared in this study. The obtained composites increases sharply from 1.57Mpa to 12.04Mpa by incorporating 5wt% nano-SiO2. Furthermore, the composites show approximately 8°C higher glass transition temperature (Tg) than that of neat PPC.The Tdmax of composite with 5wt% of nano-SiO2 was about 40°C higher than that of neat PPC.

scholarly journals Thermal, Physical and Mechanical Properties of Poly(Butylene Succinate)/Kenaf Core Fibers Composites Reinforced with Esterified Lignin

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2359
Author(s):  
Harmaen Ahmad Saffian ◽  
Masayuki Yamaguchi ◽  
Hidayah Ariffin ◽  
Khalina Abdan ◽  
Nur Kartinee Kassim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Loss Modulus ◽  
Physical And Mechanical Properties ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Esterification Reaction ◽  
Butylene Succinate ◽  
Kenaf Core ◽  
Modified Lignin

In this study, Kraft lignin was esterified with phthalic anhydride and was served as reinforcing filler for poly(butylene succinate) (PBS). Composites with different ratios of PBS, lignin (L), modified lignin (ML) and kenaf core fibers (KCF) were fabricated using a compounding method. The fabricated PBS composites and its counterparts were tested for thermal, physical and mechanical properties. Weight percent gain of 4.5% after lignin modification and the FTIR spectra has confirmed the occurrence of an esterification reaction. Better thermo-mechanical properties were observed in the PBS composites reinforced with modified lignin and KCF, as higher storage modulus and loss modulus were recorded using dynamic mechanical analysis. The density of the composites fabricated ranged from 1.26 to 1.43 g/cm3. Water absorption of the composites with the addition of modified lignin is higher than that of composites with unmodified lignin. Pure PBS exhibited the highest tensile strength of 18.62 MPa. Incorporation of lignin and KCF into PBS resulted in different extents of reduction in tensile strength (15.78 to 18.60 MPa). However, PBS composite reinforced with modified lignin exhibited better tensile and flexural strength compared to its unmodified lignin counterpart. PBS composite reinforced with 30 wt% ML and 20 wt% KCF had the highest Izod impact, as fibers could diverge the cracking propagation of the matrix. The thermal conductivity value of the composites ranged from 0.0903 to 0.0983 W/mK, showing great potential as a heat insulator.

scholarly journals Styrene–Acrylic Emulsion with “Transition Layer” for Damping Coating: Synthesis and Characterization

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1406
Author(s):  
Daoyuan Chen ◽  
Mingjin Ding ◽  
Zhixiong Huang ◽  
Yanbing Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Transition Layer ◽  
Testing Machine ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Latex Film ◽  
Seeded Emulsion Polymerization ◽  
Acrylic Emulsion ◽  
Dynamic Mechanical

In order to study the dynamic mechanical properties of styrene–acrylic latex with a core/shell structure, a variety of latexes were synthesized by semi-continuous seeded emulsion polymerization based on “particle design” with the same material. The latexes were characterized by rotary viscosimeter, dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), transmission electron microscope (TEM), dynamic mechanical analysis (DMA), and universal testing machine. The effects of difference at the glass transition temperature (Tg) of core and shell and the introduction of the “transition layer” on the damping and mechanical properties of latex film were studied. The results indicate that as the Tg of core and shell gets closer, the better the compatibility of core and shell, from phase separation to phase continuity. Furthermore, the introduction of the “transition layer” can effectively improve the tensile strength and tan δ (max) of the latex film. The tensile strength and maximum loss factor (f = 1 Hz) of latex with the “transition layer” increased by 36.73% and 29.11% respectively compared with the latex without the “transition layer”. This work provides a reference for the design of emulsion for damping coating.

Sign in / Sign up

Export Citation Format

Share Document