Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

scholarly journals Effect of Ading Nanocarbon Black on the Mechanical Properties of Epoxy

2014 ◽  
Vol 7 (1) ◽  
pp. 94-108
Author(s):  
Amer Hameed Majeed ◽  
Mohammed S. Hamza ◽  
Hayder Raheem Kareem
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Carbon Black ◽  
Modulus Of Elasticity ◽  
Tensile Modulus ◽  
Dispersion Method ◽  
Carbon Black Nanoparticles

The study covers the effect of nanocarbon black particles (N220) on some important mechanical properties of epoxy reinforced with it [carbon black nanoparticles]. The nanocomposites were prepared with (1 to 10 wt. %) of carbon black nanoparticles using ultrasonic wave bath machine dispersion method. The results had shown that the tensile strength , tensile modulus of elasticity, flexural strength and impact strength are improved by (24.02%,7.93%,17.3% and 6% ) respectively at 2wt % .The compressive strength and hardness are improved by (44.4%, 12%) at 4wt%.

Morphology and mechanical properties of polypropylene/ethylene acrylic acid/maleic anhybride-grafted polypropylene/organoclay nanocomposites

2016 ◽  
Vol 30 (3) ◽  
pp. 341-357 ◽  
Author(s):  
Qin Tian ◽  
Shuhao Qin ◽  
Fuzhong Wu ◽  
Huixin Jin ◽  
Ming Yang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Acrylic Acid ◽  
Impact Strength ◽  
Flexural Strength ◽  
Storage Modulus ◽  
Flexural Modulus ◽  
Reaction Medium ◽  
Melt Mixing

Polypropylene (PP)/ethylene acrylic acid (EAA)/maleic anhybride-grafted PP (PP- g-MA)/organoclay nanocomposites were prepared using the melt mixing technique, and PP- g-MA and EAA were employed as the compatibilizers. The sodium montmorillonite (MMT) were pretreated with high-speed airflow pulverization method and then grafted using γ-glycidoxypropyltrimethoxysilane, followed by modification using trihexyltetradecylphosphonium chloride cation with supercritical carbon dioxide as the reaction medium (the obtained product was abbreviated as OGMMT). The modification of MMT was characterized by thermogravimetric analysis, X-ray diffraction (XRD), and scanning electron microscopy. The effect of organoclay content on microstructure and mechanical properties of PP/EAA/PP- g-MA/OGMMT nanocomposites was investigated by XRD, transmission electron microscopy, dynamic mechanical analysis, tensile strength, notched impact strength, flexural strength, and flexural modulus. The results show that the OGMMT has a high weight loss, a large d-spacing increment, and exfoliation predomination structure. The addition of compatibilizers benefited the formation of exfoliated structure and the dispersion of OGMMT in PP matrix, and hence, enhanced the storage modulus ( G′) below the glass transition temperature ( Tg), storage modulus ( G″), Tg, tensile strength, flexural strength, and flexural modulus of the nanocomposites. Furthermore, with the increasing OGMMT content, the nanocomposites exhibited very inconsiderable alteration in the clay dispersion level and enhanced G′ below the Tg, G″, tensile strength, flexural strength, and flexural modulus of the nanocomposites, whereas the Tg was invariant. As a whole, the introduction of compatibilizers and OGMMT led to the reduction of notched impact strength, which also nearly linearly decreased with increasing clay content.

scholarly journals Compression Molded Thermoplastic Composites Entirely Made of Recycled Materials

2019 ◽  
Vol 11 (3) ◽  
pp. 631 ◽  
Author(s):  
Petri Sormunen ◽  
Timo Kärki
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Tensile Modulus ◽  
Mineral Wool ◽  
Thermoplastic Composites ◽  
Filler Materials ◽  
Melt Mixing ◽  
Hot Melt ◽  
Composite Samples

Recycled post-consumer high-density polyethylene pipe plastic was agglomerated into composite samples with wood, glass fiber, mineral wool, gypsum, and soapstone as recycled particulate fillers. The tensile strength, tensile modulus, impact strength, and hardness were the mechanical properties evaluated. Scanning electron microscopy was performed on the broken surfaces of tensile strength samples to study the interfacial interactions between the composite matrix and the filler materials. Heat build-up, water absorption, and thickness swelling were the physical properties measured from the composites. The addition of particulate fillers demonstrated the weakening of the tensile and impact strength but significantly improved the rigidity of the post-consumer plastic. The composites filled with minerals had mechanical properties comparable to compression molded wood plastic composites but higher resistance to moisture. A lack of hot-melt mixing affected the mechanical properties adversely.

Poly(Butylene Succinate) Composites Reinforced with Short Sisal Fibres

2001 ◽  
Vol 9 (5) ◽  
pp. 333-338 ◽  
Author(s):  
Mitsuhiro Shibata ◽  
Retsu Makino ◽  
Ryutoku Yosomiya ◽  
Hiroyuku Takeishi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fibre Length ◽  
Mechanical Analysis ◽  
Fibre Content ◽  
Flexural Properties ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Sisal Fibre ◽  
The Matrix

Poly(butylene succinate) composites reinforced with short sisal fibre were prepared by melt mixing and subsequent injection moulding. The influence of fibre length, fibre content and the surface treatment of the natural fibres on the mechanical properties of the composites were evaluated. Regarding fibre length, the tensile and flexural properties of the composites had maxima at a fibre length of about 5 mm. The flexural and tensile moduli of the composites increased with increasing fibre content. Although the tensile strength hardly changed, the flexural strength increased up to a fibre content of 10 wt%. The dynamic mechanical analysis of the composites showed that the storage moduli at above ca.-16°C (corresponding to the glass transition temperature of the matrix) increased with increasing fibre content.

Electrical and Mechanical Properties of Carbon Aerogels / Phenolic Resin for Nanocomposites

2011 ◽  
Vol 236-238 ◽  
pp. 1725-1730 ◽  
Author(s):  
Wei Jen Chen ◽  
Ming Yuan Shen ◽  
Yi Luen Li ◽  
Chin Lung Chiang ◽  
Ming Chuen Yip
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Phenolic Resin ◽  
Surface Conductivity ◽  
Carbon Aerogels ◽  
Polymer Resin ◽  
The Impact ◽  
Humidity Environment

This study used carbon aerogels (CA) and phenolic resin in fixed proportations to produce nano high polymer resin, and used poly ehtylene oxide (PEO) as the modifying agent for phenolic resin to improve the mechanical properties of phenolic resin and promote the surface conductivity. The prepared nano high polymer resin and carbon cloth were made into nano-prepreg by using ultrasonic impregnation method, and a nano-prepreg composite material was prepared by using hot compacting and cut to test pieces to measure its mechanical properties and surface conductivity as well as the influence of temperature-humidity environment (85°C/168hr and 85°C/85%RH/168hr) on mechanical properties. The result showed that the surface conductivity increased by 64.55%, the tensile strength at room temperature increased by 35.7%, the flexural strength increased by 18.4%, and the impact strength increased by 101%. In hot environment (85°C/168hr), the tensile strength decreased by 23.8%, the flexural strength increased by 3.1%, and the impact strength increased by 84.6%. In high temperature-high humidity environment (85°C/85% RH/168hr), the tensile strength decreased by 29.6%, the flexural strength decreased by 17%, and the impact strength increased by 95.7%.Introduction

Development of New TiO2 Nanoparticles Modified Photosensitive Resin for Rapid Prototyping

2020 ◽  
Vol 12 (2) ◽  
pp. 244-248
Author(s):  
Yiwen Xu ◽  
Shengcai Qi ◽  
Yuanzhi Xu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Rapid Prototyping ◽  
Tensile Modulus ◽  
Heat Stability ◽  
Scanning Calorimetry ◽  
Photosensitive Resin ◽  
Cost Efficient ◽  
Thermal Stability Of

The objective of this study is to enhance the thermal and mechanical properties of the photosensitive resin for RP (Rapid Prototyping) modifying with TiO2 nanoparticles NPs. The coupling agent KH570 was chosen for treating the surface of TiO2 NPs. The influence of the TiO2 content on the viscosity and the curing depth of photosensitive resin were analyzed in this study. We also tested the mechanical properties such as tensile modulus, tensile strength, hardness and flexural strength. Using differential scanning calorimetry, we tested the thermal stability of the modified photosensitive resin. Modified photosensitive resin's comprehensive performance was really good when the content of TiO2 was at 0.25%, the increase in tensile strength from 24.3 to 46.9 MPa was noticed to be 89%, the increase in tensile modulus from 1990 to 2251 MPa was noticed to be 18%, the increase in hardness and flexural strength was noticed to be 5 and 6%, respectively. Moreover, the heat stability and plasticity of the modified photosensitive resin are also enhanced. This paper gives a cost-efficient method of improving the functioning of photosensitive resin for RP.

Mechanical Properties of Poly(Butylene Succinate) Reinforced with Alpha Cellulose

2015 ◽  
Vol 1119 ◽  
pp. 283-287
Author(s):  
Sarit Liprapan ◽  
Thumnoon Nhujak ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Glycidyl Methacrylate ◽  
Interfacial Interaction ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Butylene Succinate ◽  
Twin Screw

The objective of this study is to prepare α-cellulose reinforced poly (butylene succinate) composites (PBS/α-cellulose). The effect of amount α-cellulose on the mechanical properties of the composites was investigated. To improve interfacial interaction between PBS and α-cellulose, glycidyl methacrylate grafted poly (butylene succinate) (PBS-g-GMA) was used as a compatibilizer. Mechanical properties of PBS composites prepared by using a twin-screw extruder were investigated. The mechanical properties of PBS/α-cellulose decreased due to the agglomeration of α-cellulose. Nevertheless, tensile strength, Young’s modulus and flexural strength of PBS composites were improved after the incorporation of PBS-g-GMA. The optimum loading of PBS-g-GMA and α-cellulose in the PBS was found to be 5 and 6 phr.

Effects of the Size of Wood Flour on Mechanical Properties of Wood-Plastic Composites

2011 ◽  
Vol 393-395 ◽  
pp. 76-79 ◽  
Author(s):  
Hai Bing Huang ◽  
Hu Hu Du ◽  
Wei Hong Wang ◽  
Hai Gang Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Wood Flour ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Inorganic Filler ◽  
Full Potential ◽  
Wood Plastic Composites ◽  
Plastic Composites

In this article, wood-plastic composites(WPCs) were manufactured with wood flour(80～120mesh、40～80mesh、20～40mesh、10～20mesh) combing with high density polyethylene(HDPE). Effects of the size of wood flour on mechanical properies and density of composites were investigated. Results showed that particle size of wood flour had an important effect on properitiesof WPCs. Change of mesh number had a outstanding effect on flexural modulus, tensile modulus and impact strength, howere, little effect on flexural strength and tensile strength. When mesh number of wood flour changed from 80～120mesh to 10～20mesh,flexural modulus and tensile modulus were respectively enhanced by 42.4% and 28.4%, respectively, and impact strength was decreased by 35.5%.Size of wood flour basically had no effect on density of composite within 10～120mesh. The use of wood flour or fiber as fillers and reinforcements in thermoplastics has been gaining acceptance in commodity plastics applications in the past few years. WPCs are currently experiencing a dramatic increase in use. Most of them are used to produce window/door profiles,decking,railing,ang siding. Wood thermoplastic composites are manufactured by dispering wood fiber or wood flour(WF) into molten plastics to form composite materials by processing techniques such as extrusion,themoforming, and compression or injection molding[1]. WPCs have such advantages[2]：(1)With wood as filler can improve heat resistance and strength of plastic, and wood has a low cost, comparing with inorganic filler, wood has a low density. Wood as strengthen material has a great potential in improving tensile strength and flexural modulus[3]；(2) For composite of same volume, composites with wood as filler have a little abrasion for equipment and can be regenerated；(3)They have a low water absorption and low hygroscopic property, They are not in need of protective waterproof paint, at the same time, composite can be dyed and painted for them own needs；(4)They are superior to wood in resistantnce to crack、leaf mold and termite aspects, composites are the same biodegradation as wood；(5)They can be processed or connected like wood；（6）They can be processed into a lots of complicated shape product by means of extrusion or molding and so on, meanwhile, they have high-efficiency raw material conversion and itself recycle utilization[4]. While there are many sucesses to report in WPCs, there are still some issues that need to be addressed before this technology will reach its full potential. This technology involves two different types of materials: one hygroscopic(biomass) and one hydrophobic(plastic), so there are issues of phase separation and compatibilization[5]. In this paper, Effects of the size of wood powder on mechanical properties of WPCs were studied.

Mechanical Properties of Reinforced Polymer Concrete with Three Types of Resin Systems

2022 ◽  
pp. 1-24
Author(s):  
Mostafa Hassani Niaki ◽  
Morteza Ghorbanzadeh Ahangari ◽  
Abdolhossein Fereidoon
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polyurethane Foam ◽  
Basalt Fiber ◽  
Polymer Concrete ◽  
Weight Percentage ◽  
Reinforced Polymer

This paper studies the mechanical properties of polymer concrete (PC) with three types of resin systems. First, the effect of 0.5 wt% up to 3 wt% basalt fiber on the mechanical properties of a quaternary epoxy-based PC is investigated experimentally, and the best weight percentage of basalt fiber is obtained. The results show that adding basalt fiber to PC caused the greatest enhancement within 10% in compressive strength, 10% in flexural strength, 35% in the splitting tensile strength, and 315% in impact strength. In the next step, the effect of nanoclay particles on the mechanical properties of basalt fiber-reinforced PC (BFRPC) is analyzed experimentally. Nanoclays increase the compressive strength up to 7%, flexural strength up to 27%, and impact strength up to 260% but decrease the tensile strength of the PC. Field-emission scanning electron microscopy (FESEM) analysis is performed to study the fracture surface and morphology of various concrete specimens. In the last step, we consider the effect of two other different resin systems, rigid polyurethane and rigid polyurethane foam on the mechanical properties of reinforced polymer concrete. A comparison study presents that the epoxy PC has a higher specific strength than the polyurethane and ultra-lightweight polyurethane foam PC.

Direct Reactive Compatibilization of GMA on PE/Wood-Flour Composite

2011 ◽  
Vol 378-379 ◽  
pp. 735-739
Author(s):  
Yue Wen Li ◽  
Xin Hua Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Wood Flour ◽  
Reactive Extrusion ◽  
Rupture Surface ◽  
Elongation At Break ◽  
Reactive Compatibilization ◽  
Anchoring Strength

Reactive compatibilization between high-density polyethylene(HDPE) and wood-flour was achieved via direct reactive extrusion of glycidyl methacrylate(GMA), initiator, HDPE and wood-flour. Impact rupture surface of the composite was observed by scanning electron microscope(SEM), and its load deformation temperature(HDT) and mechanical properties were tested. Effect of GMA dosage and extrusion temperature on reactive compatibilization of the composite was analysed. The result indicated that the anchoring strength of interface in the composite was obviously strengthened, and its HDT, tensile strength, flexural strength, notched impact strength and elongation at break of the composite were distinctly improved due to the addition of GMA and dicumyl peroxide(DCP). When the composite was extruded at 180°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 84°C, 40Mpa, 45Mpa, 11% and 6.6KJ.m-2, which respectively increased by 17°C, 74%, 36%, 83% and 69% than that of the composite without reactive compatibilization, and when the composite was extruded at 190°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 84°C, 40Mpa, 44Mpa, 11% and 6.6KJ.m-2, which respectively increased by 20°C, 60%, 26%, 83% and 83% than that of the composite without reactive compatibilization. When GMA usage increased, the HDT and mechanical properties of the composite increased first, then descended, and the optimum usage of GMA was 1wt%-3wt%.

Sign in / Sign up

Export Citation Format

Share Document