Influence of injection strategies on knock resistance and combustion characteristics in a DISI engine

2018 ◽  
Vol 233 (10) ◽  
pp. 2637-2649
Author(s):  
Haiqiao Wei ◽  
Jie Yu ◽  
Aifang Shao ◽  
Lei Zhou ◽  
Jianxiong Hua ◽  
...  
Keyword(s):  
Single Injection ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Combustion Stability ◽  
Injection Timing ◽  
Split Injection ◽  
Injection Strategy ◽  
Double Injection ◽  
The Impact ◽  
Injection Strategies

The combustion of a direct injection spark ignition engine is significantly affected by the fuel injection strategy due to the impact this strategy has on the gas-mixture formation and the turbulence flow. However, comprehensive assessments on both knock and engine performances for different injection strategies are generally lacking. Therefore, the main objective of the present study is to provide an experimental evidence of how a single injection strategy and a split injection strategy compare in terms of both knock tendency and engine performances like thermal efficiency, torque and combustion stability. Starting from the optimization of a single injection strategy, a split injection strategy is then evaluated. Under the present operating conditions, an optimum secondary injection timing of 100 CAD BTDC is found to have significant improvements on both the knock resistance and the overall engine performances. It should be noted that the present results indicate that the relationship between double injection and anti-knock performance is not monotonous. In addition, the double injection shows superior potential in improving fuel economy and power performance in contrast with the single injection thanks to a more stable combustion when a late injection timing is applied.

Effect of Injection Timing on PPCI and MPCI Mode Fueled With Straight-Run Naphtha

2013 ◽  
Vol 136 (3) ◽  
Author(s):  
Hongqiang Yang ◽  
Shijin Shuai ◽  
Zhi Wang ◽  
Jianxin Wang
Keyword(s):  
Diesel Fuel ◽  
Single Injection ◽  
Operating Conditions ◽  
Premixed Combustion ◽  
Spray Combustion ◽  
Injection Timing ◽  
Soot Emission ◽  
Compression Ignition ◽  
Injection Strategy ◽  
Injection Strategies

Partially premixed compression ignition (PPCI) and multiple premixed compression ignition (MPCI) mode of straight-run naphtha have been investigated under different injection strategies. The MPCI mode is realized by the multiple premixed combustion processes in a sequence of “spray-combustion-spray-combustion” around the compression top dead center. The spray and combustion events are preferred to be completely separated, without any overlap in the temporal sequence in order to ensure the multiple-stage premixed compression ignition. The PPCI mode is well known as the “spray-spray-combustion” sequence, with the start of combustion separated from the end of injection. Straight-run naphtha with a research octane number (RON) of 58.8 is tested in a single cylinder compression ignition engine whose compression ratio is 16.7 and displacement is 0.5 l. Double and triple injection strategies are investigated as the last injection timing sweeping at 1.0 MPa IMEP and 1800 rpm conditions. The MPCI mode is achieved using the double injection strategy, but its soot emission is higher than the PPCI mode under triple injection strategy. This is mainly because of the lower RON of the straight-run naphtha and the ignition delay is too short to form an ideally premixed combustion process after the second injection of straight-run naphtha. Diesel fuel is also tested under the same operating conditions, except for employing a single injection strategy. The naphtha PPCI and MPCI mode both have lower fuel consumption and soot emission than diesel fuel single injection mode, but the THC emissions are both higher than that of diesel fuel.

Effects of split and single injection strategies on particle number emission and combustion of a GDI engine

2018 ◽  
Vol 233 (5) ◽  
pp. 1100-1114 ◽  
Author(s):  
Fangxi Xie ◽  
Wenliang Zheng ◽  
Hong Chen ◽  
Yu Liu ◽  
Yan Su ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Particle Number ◽  
Fuel Injection ◽  
Single Injection ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Brake Specific Fuel Consumption ◽  
Split Injection ◽  
Injection Strategy ◽  
Injection Strategies

Influence of fuel injection parameters of the single and split injection strategies on combustion, performance and particle number emission had been investigated on a gasoline direct injection engine with stoichiometric mixture combustion under medium and low engine operating conditions. The test results showed that the optimal injection timing for single injection strategy was about 290–280 °CA BTDC, and an earlier or a later injection timing could lead to a deterioration of particle number emission. For split injection strategy, the injected parameters also needed to be optimized subtly in order to improve particle number emission. When the inappropriate injected parameters were adopted, particle number emission increased rather than decrease when compared with single injection strategy. Similar to single injection strategy, when the second injection timing of split injection strategy further retarded from 280 °CA BTDC, the particle number emission and brake-specific fuel consumption also started to deteriorate, and the in-cylinder combustion process was delayed and slowed. The optimal first injection timing was about 300 °CA BTDC. When the first injection timing was delayed to 280 °CA BTDC with the second injection timing being 260 °CA BTDC, the particle number emission increased and the shortened interval time between first and second fuel injection might have had a negative effect. The smaller difference of the fuel quantity between the first and the second injection was not good for the improvement of particle number emission and brake-specific fuel consumption, and the best injection proportion was 2:8. Overall, the engine particle number emission could be decreased to some extent, which could reach about 10–30%, by split injection strategy with optimal control parameters at medium and low engine loads.

scholarly journals Effect of Cylinder-by-Cylinder Variation on Performance and Gaseous Emissions of a PFI Spark Ignition Engine: Experimental and 1D Numerical Study

2021 ◽  
Vol 11 (13) ◽  
pp. 6035
Author(s):  
Luigi Teodosio ◽  
Luca Marchitto ◽  
Cinzia Tornatore ◽  
Fabio Bozza ◽  
Gerardo Valentino
Keyword(s):  
Internal Combustion Engines ◽  
Numerical Study ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Combustion Stability ◽  
Pollutant Emissions ◽  
Gaseous Emissions ◽  
Performance And Emissions ◽  
The Impact

Combustion stability, engine efficiency and emissions in a multi-cylinder spark-ignition internal combustion engines can be improved through the advanced control and optimization of individual cylinder operation. In this work, experimental and numerical analyses were carried out on a twin-cylinder turbocharged port fuel injection (PFI) spark-ignition engine to evaluate the influence of cylinder-by-cylinder variation on performance and pollutant emissions. In a first stage, experimental tests are performed on the engine at different speed/load points and exhaust gas recirculation (EGR) rates, covering operating conditions typical of Worldwide harmonized Light-duty vehicles Test Cycle (WLTC). Measurements highlighted relevant differences in combustion evolution between cylinders, mainly due to non-uniform effective in-cylinder air/fuel ratio. Experimental data are utilized to validate a one-dimensional (1D) engine model, enhanced with user-defined sub-models of turbulence, combustion, heat transfer and noxious emissions. The model shows a satisfactory accuracy in reproducing the combustion evolution in each cylinder and the temperature of exhaust gases at turbine inlet. The pollutant species (HC, CO and NOx) predicted by the model show a good agreement with the ones measured at engine exhaust. Furthermore, the impact of cylinder-by-cylinder variation on gaseous emissions is also satisfactorily reproduced. The novel contribution of present work mainly consists in the extended numerical/experimental analysis on the effects of cylinder-by-cylinder variation on performance and emissions of spark-ignition engines. The proposed numerical methodology represents a valuable tool to support the engine design and calibration, with the aim to improve both performance and emissions.

scholarly journals Numerical Investigation of an RCCI Engine Fueled with Natural Gas/Dimethyl-Ether in Various Injection Strategies

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1638
Author(s):  
Ayat Gharehghani ◽  
Alireza Kakoee ◽  
Amin Mahmoudzadeh Andwari ◽  
Thanos Megaritis ◽  
Apostolos Pesyridis
Keyword(s):  
Fuel Injection ◽  
Single Injection ◽  
Split Injection ◽  
Lower Efficiency ◽  
Injection Strategy ◽  
Compression Ignition Engines ◽  
Start Of Injection ◽  
Single Strategy ◽  
Direct Fuel Injection ◽  
Injection Strategies

Reactivity control compression ignition engines illustrated suitable abilities in emission reduction beside high thermal efficiency. In this research, nine various direct fuel injection strategies were studied numerically: three cases with single injection strategy and six cases with split injection and different start of injection (SOI). In all simulated cases, equivalence ratio kept constant (i.e., 0.3). Among various strategies, single injection showed higher IMEP as a factor of efficiency with about 5.39 bar that occurred at SOI = 60 before top dead center (bTDC), while lower efficiency was observed for split injection case with 50%-50% injections of fuel in each injection stage. Start of combustion (SOC), burn duration and CA50 as factors for combustion characteristics were affected with SOI changes. In single SOI strategies, more advanced injection caused more advanced SOC where there was about 1.3 CAD advancing from 40 to 80 bTDC injection. Spilt SOI showed more advanced SOC, which, also more advanced, was allocated to 50%-50% split injection strategy. There was also the same trend in CA50 changes during change in SOI. Burn duration variations were insignificant and all of them approximately close to 4.5 CAD. According to the emissions researched in this study (Nitrogen Oxides (NOx), monoxide carbon (CO) and unburned hydro carbons (UHC)), all of these pollutants are below euro six diesel standards. Contours of emissions show that there were appropriate SOI for each case study, which were 45 degree bTDC for single strategy, 48 degree bTDC for 80%-20% mass injection and 70 degree bTDC for 50%-50% cases.

scholarly journals Experimental Investigation of Injection Strategies on Low Temperature Combustion Fuelled with Gasoline in a Compression Ignition Engine

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Binbin Yang ◽  
Mingfa Yao ◽  
Zunqing Zheng ◽  
Lang Yue
Keyword(s):  
Experimental Investigation ◽  
Thermal Efficiency ◽  
High Efficiency ◽  
Single Injection ◽  
Combustion Efficiency ◽  
Soot Emission ◽  
Compression Ignition Engine ◽  
Injection Strategy ◽  
Double Injection ◽  
Injection Strategies

The present study focuses on the experimental investigation on the effect of fuel injection strategies on LTC with gasoline on a single-cylinder CI engine. Firstly, the engine performance and emissions have been explored by sweeping SOI1 and split percentage for the load of 0.9 MPa IMEP at an engine speed of 1500 rpm. Then, the double-injection strategy has been tested for load expansion compared with single-injection. The results indicate that, with the fixed CA50, the peak HRR is reduced by advancing SOI1 and increasing split percentage gradually. Higher indicated thermal efficiency, as well as lower MPRR and COV, can be achieved simultaneously with later SOI1 and higher split percentage. As split percentage increases,NOXemission decreases but soot emission increases. CO and THC emissions are increased by earlier SOI1, resulting in a slight decrease in combustion efficiency. Compared with single-injection, the double-injection strategy enables successful expansion of high-efficiency and clean combustion region, with increasing soot, CO, and THC emissions at high loads and slightly declining combustion efficiency and indicated thermal efficiency, however. MPRR and soot emission are considered to be the predominant constraints to the load expansion of gasoline LTC, and they are related to their trade-off relationship.

An Investigation of Multi-Injection Strategies for a Dual-Fuel Pilot Diesel Ignition Engine at Low Load

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Amin Yousefi ◽  
Madjid Birouk
Keyword(s):  
Single Injection ◽  
Fluid Dynamic ◽  
Engine Performance ◽  
Dual Fuel ◽  
Injection Timing ◽  
Double Injection ◽  
Indicated Mean Effective Pressure ◽  
Soot Emissions ◽  
Injection Pulse ◽  
Injection Strategies

A multidimensional computational fluid dynamic (CFD) model was developed in order to explore the combined effect of injection timing and fuels quantity ratio of different injection strategies on the combustion performance and emissions characteristics of a dual-fuel indirect injection (IDI) engine with a pilot diesel ignition. The total mass of pilot diesel and premixed natural gas equivalence ratio were kept constant while various injection strategies (single, double, and triple) were investigated at 25% engine load and speed of 800 rpm. Results revealed that the released heat of triple injection pulse during the expansion stroke is the same or higher than that of single and double injection pulses at specified injection timings. It affects positively the engine performance. The highest indicated mean effective pressure (IMEP) can be achieved using single injection pulse at all first injection timings. It is observed that double and triple injection pulses possess comparable indicated thermal efficiency (ITE) and IMEP to those of single injection at specified injection timings. The highest ITE is found 47.5% at first injection timing of −16 deg after top dead center (ATDC) for both single and double injection pulses. Nitrogen oxides (NOx) mole fraction generally increases when retarding the injection timing. By applying double and triple injection pulses, NOx emissions decrease, on average, by 9% and 14% compared to that of the single injection pulse. Using double and triple injection pulses, soot emissions increase, on average, by 10% and 32%, respectively, compared to single injection pulse. However, at specified injection timings, the effect of all injection pulses on soot emissions is negligible at relative advanced first injection timing. Carbon monoxide (CO) emissions decrease slightly for all injection strategies when the injection timing varies from −20 deg ATDC to −12 deg ATDC. In this range, dual-fuel operation with triple injection pulse produces the lowest CO emissions. By using triple injection pulse at suitable injection timings, CO emissions decrease by around 7.4% compared to single injection pulse. However, by applying double and triple injection pulses, unburned methane increases, on average, by 16% and 52%, respectively, compared with that of single injection pulse. However, at injection timings of −12 deg ATDC and −8 deg ATDC, triple and double injection pulses produce comparable level of unburned methane to that of single injection pulse.

scholarly journals Ethanol/Gasoline Blends as Alternative Fuel in Last Generation Spark-Ignition Engines: A Review on CO and HC Engine Out Emissions

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 4034
Author(s):  
Paolo Iodice ◽  
Massimo Cardone
Keyword(s):  
Physicochemical Properties ◽  
Alternative Fuels ◽  
Experimental Studies ◽  
Alternative Fuel ◽  
Exhaust Emissions ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Spark Ignition Engines ◽  
The Impact

Among the alternative fuels existing for spark-ignition engines, ethanol is considered worldwide as an important renewable fuel when mixed with pure gasoline because of its favorable physicochemical properties. An in-depth and updated investigation on the issue of CO and HC engine out emissions related to use of ethanol/gasoline fuels in spark-ignition engines is therefore necessary. Starting from our experimental studies on engine out emissions of a last generation spark-ignition engine fueled with ethanol/gasoline fuels, the aim of this new investigation is to offer a complete literature review on the present state of ethanol combustion in last generation spark-ignition engines under real working conditions to clarify the possible change in CO and HC emissions. In the first section of this paper, a comparison between physicochemical properties of ethanol and gasoline is examined to assess the practicability of using ethanol as an alternative fuel for spark-ignition engines and to investigate the effect on engine out emissions and combustion efficiency. In the next section, this article focuses on the impact of ethanol/gasoline fuels on CO and HC formation. Many studies related to combustion characteristics and exhaust emissions in spark-ignition engines fueled with ethanol/gasoline fuels are thus discussed in detail. Most of these experimental investigations conclude that the addition of ethanol with gasoline fuel mixtures can really decrease the CO and HC exhaust emissions of last generation spark-ignition engines in several operating conditions.

scholarly journals Effects of the Multiple Injection Strategy on Combustion and Emission Characteristics of a Two-Stroke Marine Engine

Energies ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6821
Author(s):  
Ju-Hwan Seol ◽  
Van Chien Pham ◽  
Won-Ju Lee
Keyword(s):  
Single Injection ◽  
Simulation Software ◽  
Emission Characteristics ◽  
Cylinder Pressure ◽  
Multiple Injection ◽  
Injection Strategy ◽  
Marine Engine ◽  
Injection Mode ◽  
Double Injection ◽  
Simulation Results

This paper presents research on the effects of the multiple injection strategies on the combustion and emission characteristics of a two-stroke heavy-duty marine engine at full load. The ANSYS FLUENT simulation software was used to conduct three-dimensional simulations of the combustion process and emission formations inside the engine cylinder in both single- and double-injection modes to analyze the in-cylinder pressure, temperature, and emission characteristics. The simulation results were then compared and showed good agreement with the measured values reported in the engine’s sea-trial technical reports. The simulation results showed reductions in the in-cylinder pressure and temperature peaks by 6.42% and 12.76%, while NO and soot emissions were reduced up to 24.16% and 68%, respectively, in the double-injection mode in comparison with the single-injection mode. However, the double-injection strategy increased the CO2 emission (7.58%) and ISFOC (23.55%) compared to the single-injection. These are negative effects of the double-injection strategy on the engine that the operators need to take into consideration. The results were in line with the literature reviews and would be good material for operators who want to reduce the engine exhaust gas emission in order to meet the stricter IMO emission regulations.

Effect of injection and ignition timing on a hydrogen-lean stratified charge combustion engine

2021 ◽  
pp. 146808742110346
Author(s):  
Sanguk Lee ◽  
Gyeonggon Kim ◽  
Choongsik Bae
Keyword(s):  
Internal Combustion Engines ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Stability ◽  
Transport Sector ◽  
Injection Timing ◽  
Ignition Timing ◽  
Particulate Emission ◽  
Stratified Charge ◽  
Lean Limit

Hydrogen can be used as a fuel for internal combustion engines to realize a carbon-neutral transport society. By extending the lean limit of spark ignition engines, their efficiency, and emission characteristics can be improved. In this study, stratified charge combustion (SCC) using monofueled hydrogen direct injection was used to extend the lean limit of a spark ignition engine. The injection and ignition timing were varied to examine their effect on the SCC characteristics. An engine experiment was performed in a spray-guided single-cylinder research engine, and the nitrogen oxide and particulate emissions were measured. Depending on the injection timing, two different types of combustion were characterized: mild and hard combustion. The advancement and retardation of the ignition timing resulted in a high and low combustion stability, respectively. The lubricant-based particulate emission was attributed to the in-cylinder temperature and area of the flame surface. Therefore, the results of the study suggest that the optimization of the hydrogen SCC based on the injection and ignition timing could contribute to a clean and efficient transport sector.

Effect of Split Injection Timing on Combustion and Emissions of a DISI Optical Engine Under Lean Burn Condition

2020 ◽  
Author(s):  
Zhe Sun ◽  
Mingli Cui ◽  
Hongyu Wang ◽  
Mohamed Nour ◽  
Xuesong Li ◽  
...  
Keyword(s):  
High Energy ◽  
Flame Speed ◽  
Operating Conditions ◽  
Image Processing Technique ◽  
Injection Timing ◽  
Split Injection ◽  
Lean Burn ◽  
Combustion Performance ◽  
Optical Engine ◽  
Lean Combustion

Abstract Lean combustion has proven to be an effective way to improve the efficiency and emissions of the direct injection spark ignition (DISI) engine. However, one of the main problems at the lean stability limit is the major decrease in flame temperature due to dilution, resulting in a low laminar flame speed, especially under low-speed engine operating conditions. The split injection is a potential technology to realize proper air-fuel mixing and achieve different spray distribution that can help in solving such problems. In this study, split injections with different secondary injection timings were tested to achieve homogeneous and homogeneous-stratified modes in a DISI optical engine under lean-burn mode. The split ratio of each strategy was 1:1. The engine was operated at 800 rpm, and a high-energy ignition system was utilized to realize lean combustion at a lambda of 1.55. Engine combustion performance and emissions were tested while performing high-speed color recording to study the characteristics of flame chemiluminescence through a quartz piston combined with a 45-degree mirror installed below. Flame structure during various combustion phases was compared under different selected conditions based on a digital image processing technique. The results show that the pressure and emissions vary with the second injection timing. Proper control of the split injection timing can improve lean combustion performance, including faster flame speed, increased indicated mean effective pressure (IMEP), and lower harmful emissions. Poor fuel evaporation and soot generation from spatial hot spots in the combustion process of split injection are the major challenges for further improvement.

Sign in / Sign up

Export Citation Format

Share Document