Numerical investigation on the impact of multiple injection strategies and spray included angles on combustion and emissions in a marine diesel engine

2021 ◽  
pp. 095440702110694
Author(s):  
Shiru Kong ◽  
Changpu Zhao ◽  
Zhishang Bian ◽  
Yujie Cai
Keyword(s):  
Injection Timing ◽  
Pilot Injection ◽  
Post Injection ◽  
Simultaneous Reduction ◽  
Included Angle ◽  
Injection Duration ◽  
Marine Diesel ◽  
Main Injection ◽  
The Impact ◽  
Injection Strategies

The computational fluid dynamical software AVL-FIRE code was used for investigating the impact of multiply injection strategies and spray included angles on combustion and emissions in a marine diesel engine. The fuel injection parameters of spray included angle and pilot injection timing with pilot-main injection, as well as post injection ratio and post injection duration angle with pilot-main-post injection, were all investigated and optimized. The results indicate that retarding pilot injection timing with pilot-main injection declines high temperature region, resulting in a notable reduction in NOx emissions. Since fuel evaporation and burn are hampered by long spray penetration due to low temperature and pressure with pilot injection, a suitable spray included angle are used to offer more efficient air-fuel mixing process. A wider spray included angle simultaneously reduces soot emission and indicated specific fuel consumption (ISFC). Post injection fuel exerts impact on combustion process by causing a great disturbance to flow field during post combustion. Increasing post injection ratio from 4% to 10% at a small post injection duration angle great emission performance is achieved by simultaneous reduction in NOx and soot emissions while only using a slight consumption of ISFC. To summarize, the defeat of traditional NOx-soot trade-off occurs as both NOx and soot emissions are decreased with optimized multiple injection strategy and spray included angle. Particularly, there are respectively four cases with pilot-main injection and two cases with pilot-main-post injection, that achieve simultaneous reduction in NOx emissions, soot emission, and ISFC, compared to the prototype.

An Experimental Study on Smoke Reduction Effect of Post Injection in Combination With Pilot Injection for a Diesel Engine

2013 ◽  
Vol 136 (4) ◽  
Author(s):  
Long Liu ◽  
Naoto Horibe ◽  
Tatsuya Komizo ◽  
Issei Tamura ◽  
Takuji Ishiyama
Keyword(s):  
Diesel Engine ◽  
Injection Pressure ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pilot Injection ◽  
Post Injection ◽  
Spray Flames ◽  
Injection Quantity ◽  
Main Injection ◽  
Reduction Effect

With the universal utilization of the common-rail injection system in automotive diesel engines, the multistage injection strategies have become typical approaches to satisfy the increasingly stringent emission regulations, and especially the post injection has received considerable attention as an effective way for reducing the smoke emissions. Normally the post injection is applied in combination with the pilot injection to restrain the NOx emissions, smoke emissions, and combustion noise simultaneously, and the pilot injection condition affects the combustion process of the main injection and might affect the smoke reduction effect of the post injection. Thus this study aims at obtaining the post injection strategy to reduce smoke emissions in a diesel engine, where post injection is employed in combination with pilot injection. The experiments were performed using a single-cylinder diesel engine under various conditions of pilot and post injection with a constant load at an IMEP of 1.01 MPa, fixed speed of 1500 rpm, and NOx emissions concentration of 150 ± 5 ppm that was maintained by adjusting the EGR ratio. The injection pressure was set at 90 MPa at first, and then it was varied to 125 MPa to evaluate the effects of post injection on the smoke reduction in the case of higher injection pressure. The experimental results show that small post injection quantity with a short interval from the end of main injection causes less smoke emissions. And larger pilot injection quantity and later pilot injection timing lead to higher smoke emissions. And then, to explore and interpret the smoke emissions tendencies with varying pilot and post injection conditions, the experimental results of three-stage injection conditions were compared to those of two reference cases, which only included the pilot and main injection, and the interaction between main spray flames and post sprays was applied for analysis. Based on the comparative analysis, the larger smoke reduction effect of post injection was observed with the larger pilot injection quantity, while it is not greatly influenced by pilot injection timing. In addition, the smoke emissions can be reduced considerably by increasing the injection pressure, however the smoke reduction effect of post injection was attenuated. And all of these tendencies were able to be interpreted by considering the intensity variation of the interaction between main spray flames and post sprays.

Fuel efficiency analysis and peak pressure rise rate improvement for neat n-butanol injection strategies

2016 ◽  
Vol 231 (1) ◽  
pp. 50-65 ◽  
Author(s):  
Marko Jeftić ◽  
Zhenyi Yang ◽  
Graham T Reader ◽  
Ming Zheng
Keyword(s):  
Carbon Monoxide ◽  
Peak Pressure ◽  
Pressure Rise ◽  
Single Shot ◽  
Pilot Injection ◽  
Post Injection ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Main Injection ◽  
Injection Strategies

Engine tests were conducted to investigate the efficiency and the peak pressure rise rate performance of different fuel injection strategies for the direct injection of neat n-butanol in a compression ignition engine. Three different strategies were tested: a single-shot injection; a pilot injection; a post-injection. A single-shot injection timing sweep revealed that early injections had the highest indicated efficiency while late injections reduced the peak pressure rise rate at the cost of a slightly reduced thermal efficiency. Delayed single-shot injections also had increased emissions of nitrogen oxides, total hydrocarbon and carbon monoxide. Addition of a pilot injection had a negative effect on the peak pressure rise rate. Because of the low cetane number of butanol and the relatively lean and well-premixed air–fuel mixture, the pilot injection failed to autoignite and instead ignited simultaneously with the main injection. This resulted in slightly increased peak pressure rise rates and significantly increased unburned butanol hydrocarbon emissions. Conversely, the use of an early post-injection produced a noticeable engine power output and allowed the main injection to be shortened and the peak pressure rise rate to be substantially reduced. However, relatively early post-injections slightly reduced the indicated efficiency and increased the nitrogen oxide emissions and the carbon monoxide emissions compared with the single-shot injection strategy. These results recommended the use of a single-shot injection for low loads and medium loads owing to a superior thermal efficiency and suggested that the application of a post-injection may be more suited to high-load conditions because of the substantially reduced peak pressure rise rates.

scholarly journals Study of the soot quantification for two-stage injection of hydrogenated catalytic biodiesel in a constant-volume combustion chamber

2017 ◽  
Author(s):  
Cao Jiawei ◽  
He Zhixia ◽  
Li Bei ◽  
Zhong Wenjun ◽  
Wang Mei
Keyword(s):  
High Speed ◽  
Dwell Time ◽  
Pilot Injection ◽  
Two Stage ◽  
Injection Duration ◽  
Soot Mass ◽  
Constant Volume Combustion Chamber ◽  
Main Injection ◽  
Ambient Gas ◽  
Injection Strategies

The effect of two-stage injection strategies on the soot formation of 0# fossil diesel were investigated experimentally using a constant volume combustion chamber. The ambient conditions was kept constant as injection pressure 150 MPa, ambient gas temperature 900 K, ambient gas pressure 45 bar. A high-speed diffused back-illumination extinction imaging technique was employed to make quantitative measurement on temporal soot evolution and reacting spray liquid length and a direct high-speed camera was used to measure the ignition delay. Two-stage injection strategies were varied with different pilot and main injection time, including a sweep of dwell time in pilot-main injection and pilot injection duration. The results show that the ignition delay decreases with the increasing dwell time. It may result from the entrained surrounding gas enhance the spray combustion process. In the reacting condition, the liquid-phase penetration is slightly longer with the shorter dwell time. However, the pilot injection duration shows slighter impact. The longer dwell time contributes to more total soot mass while the different pilot injection duration barely affect the total soot mass of the main injection.DOI: http://dx.doi.org/10.4995/ILASS2017.2017.4739

scholarly journals Wavelet Analysis of the Effect of Injection Strategies on Cycle to Cycle Variation GDI Optical Engine under Clean and Fouled Injector

Processes ◽  
2019 ◽  
Vol 7 (11) ◽  
pp. 817
Author(s):  
Omar I. Awad ◽  
Zhou Zhang ◽  
Mohammed Kamil ◽  
Xiao Ma ◽  
Obed Majeed Ali ◽  
...  
Keyword(s):  
Complex Dynamics ◽  
Control Strategies ◽  
Injection Pressure ◽  
Injection Timing ◽  
Cyclic Variation ◽  
Optical Engine ◽  
Injection Duration ◽  
Cycle Variation ◽  
Short Period ◽  
Injection Strategies

High fluctuation in cyclic variations influences engine combustion negatively, leading to higher fuel consumption, lower performance, and drivability problems. This paper examines the impacts of injection strategies (injection pressure, injection timing and injection duration) on the cyclic variation of gasoline spark ignition (SI) optical engine under clean and fouled injectors. The principal oscillatory modes of the cycle to cycle variation have been identified, and the engine cycles over which these modes may persist are described. Through the wavelet power spectrum, the presence of short, intermediate and long-term periodicities in the pressure signal have been detected. It was noticed that depending on the clean and fouled injector, the long and intermediate-term periodicities may span many cycles, whereas the short-period oscillations tend to appear intermittently. Information of these periodicities could be helpful to promote efficient control strategies for better combustion. The outcomes report that the cyclic variation of the IMEP happens on multiple timescales, and thus, display complex dynamics. As the fouled injector used, mainly intermittent high-frequency fluctuations are recognized.

Post Injection Strategy for the Reduction of the Peak Pressure Rise Rate of Neat N-Butanol Combustion

2015 ◽  
Author(s):  
Marko Jeftić ◽  
Ming Zheng
Keyword(s):  
Peak Pressure ◽  
Pressure Rise ◽  
Injection Timing ◽  
Post Injection ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Injection Duration ◽  
Rise Rate

Enhanced premixed combustion of neat butanol in a compression ignition engine can have challenges with regards to the peak pressure rise rate and the peak in-cylinder pressure. It was proposed to utilize a butanol post injection to reduce the peak pressure rise rate and the peak in-cylinder pressure while maintaining a constant engine load. Post injection timing and duration sweeps were carried out with neat n-butanol in a compression ignition engine. The post injection timing sweep results indicated that the use of an early butanol post injection reduced the peak pressure rise rate and the peak in-cylinder pressure and it was observed that there was an optimal post injection timing range for the maximum reduction of these parameters. The results also showed that an early post injection of butanol increased the nitrogen oxide emissions and an FTIR analysis revealed that late post injections increased the emissions of unburned butanol. The post injection duration sweep indicated that the peak pressure rise rate was significantly reduced by increasing the post injection duration at constant load conditions. There was also a reduction in the peak in-cylinder pressure. Measurements with a hydrogen mass spectrometer showed that there was an increased presence of hydrogen in the exhaust gas when the post injection duration was increased but the total yield of hydrogen was relatively low. It was observed that the coefficient of variation for the indicated mean effective pressure was significantly increased and that the indicated thermal efficiency was reduced when the post injection duration was increased. The results also showed that there were increased nitrogen oxide, carbon monoxide, and total hydrocarbon emissions for larger post injections. Although the use of a post injection resulted in emission and thermal efficiency penalties at medium load conditions, the results demonstrated that the post injection strategy successfully reduced the peak pressure rise rate and this characteristic can be potentially useful for higher load applications where the peak pressure rise rate is of greater concern.

Optimization of operating parameters of an off-road automotive diesel engine running at highway drive conditions using Response Surface Methodology

2020 ◽  
pp. 1-48 ◽  
Author(s):  
Vinod Babu Marri ◽  
K. Madhu Murthy ◽  
G. Amba Prasad Rao
Keyword(s):  
Response Surface Methodology ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Operating Parameters ◽  
Injection Timing ◽  
Boost Pressure ◽  
Pilot Injection ◽  
Injection Quantity ◽  
Main Injection ◽  
Fuel Injection Pressure

Abstract The typical tradeoff between the two major emissions from compression ignition (CI) engines, smoke and oxides of nitrogen, is the unresolved challenge to the researchers. Techniques like engine downsizing, lowering intake oxygen concentration, multiple injections, use of retarded injection timings and higher injection pressures, etc. are widely employed for the alleviation of these harmful emissions. The influence of variation of fuel injection pressure (FIP), boost pressure, pilot injection timing (PIT), pilot injection quantity (PIQ) and main injection timing (MIT) are experimentally investigated in the present work. Mahindra mHawk four-cylinder diesel engine with provisions of a variable-geometry turbocharger (VGT), exhaust gas recirculation (EGR), and common-rail direct injection (CRDi) is chosen for the experimentation. Test runs are conducted at 1750 rpm and 80.3 N.m (4.6 bar bmep) corresponding to highway drive conditions, using 10 % EGR. Response surface methodology is employed for the design of experiments and to analyze the experimental data. Multi-objective response optimization is carried out to optimize engine-operating parameters that give desired performance and engine-out emissions. Confirmatory tests are conducted at design conditions to validate the results predicted by the model. This study reveals that the optimum performance and emission characteristics could be obtained using 120 kPa boost pressure; 61.1 MPa fuel injection pressure; 11.5 % pilot injection quantity with pilot injection at 332 °CA and main injection at 359 °CA.

Effects of fuel injection parameters on premixed charge compression ignition combustion and emission characteristics in a medium-duty compression ignition diesel engine

2019 ◽  
pp. 146808741986701 ◽  
Author(s):  
Santiago Molina ◽  
Antonio García ◽  
Javier Monsalve-Serrano ◽  
David Villalta
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Transport Sector ◽  
Injection Timing ◽  
Compression Ignition ◽  
Injection Strategy ◽  
Low Load ◽  
Main Injection ◽  
Compression Ignition Combustion ◽  
The Impact

From the different power plants, the compression ignition diesel engines are considered the best alternative to be used in the transport sector due to its high efficiency. However, the current emission standards impose drastic reductions for the main pollutants, that is, NO x and soot, emitted by this type of engines. To accomplish with these restrictions, alternative combustion concepts as the premixed charge compression ignition are being investigated nowadays. The objective of this work is to evaluate the impact of different fuel injection strategies on the combustion performance and engine-out emissions of the premixed charge compression ignition combustion regime. For that, experimental measurements were carried out in a single-cylinder medium-duty compression ignition diesel engine at low-load operation. Different engine parameters as the injection pattern timing, main injection timing and main injection fuel quantity were sweep. The best injection strategy was determined by means of a methodology based on the evaluation of a merit function. The results suggest that the best injection strategy for the low-load premixed charge compression ignition operating condition investigated implies using a high injection pressure and a triple-injection event with a delayed main injection with almost 15% of the total fuel mass injected.

scholarly journals A Numerical Study on the Pilot Injection Conditions of a Marine 2-Stroke Lean-Burn Dual Fuel Engine

Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1396
Author(s):  
Hao Guo ◽  
Song Zhou ◽  
Jiaxuan Zou ◽  
Majed Shreka
Keyword(s):  
Natural Gas ◽  
Fuel Injection ◽  
Numerical Study ◽  
Pollutant Emissions ◽  
Dual Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Lean Burn ◽  
Injection Duration ◽  
Pilot Fuel

The global demand for clean fuels is increasing in order to meet the requirements of the International Maritime Organization (IMO) of 0.5% global Sulphur cap and Tier III emission limits. Natural gas has begun to be popularized on liquefied natural gas (LNG) ships because of its low cost and environment friendly. In large-bore marine engines, ignition with pilot fuel in the prechamber is a good way to reduce combustion variability and extend the lean-burn limit. However, the occurrence of knock limits the increase in power. Therefore, this paper investigates the effect of pilot fuel injection conditions on performance and knocking of a marine 2-stroke low-pressure dual-fuel (LP-DF) engine. The engine simulations were performed under different pilot fuel parameters. The results showed that the average in-cylinder temperature, the average in-cylinder pressure, and the NOx emissions gradually decreased with the delay of the pilot injection timing. Furthermore, the combustion situation gradually deteriorated as the pilot injection duration increased. A shorter pilot injection duration was beneficial to reduce NOx pollutant emissions. Moreover, the number of pilot injector orifices affected the ignition of pilot fuel and the flame propagation speed inside the combustion chamber.

Effect of Pilot Injection on Diesel Knock in a Small-Bore Optical Engine

2012 ◽  
Author(s):  
Alvin M. Rusly ◽  
Sanghoon Kook ◽  
Evatt R. Hawkes ◽  
Renlin Zhang
Keyword(s):  
High Speed ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Cylinder Pressure ◽  
High Speed Imaging ◽  
Term Operation ◽  
Optical Engine ◽  
Injection Duration ◽  
Rise Rate ◽  
Main Injection

Diesel knock is a phenomenon that generates undesirable noise and vibration that can be destructive to diesel engine structures and components for long-term operation. The diesel knock occurs when a large quantity of air-fuel is mixed prior to combustion when the ignition delay is long. This leads to a drastic pressure rise during the premixed phase of the combustion, which is followed by a pressure ringing. The main focus of this study is to examine effect of pilot injection on the pressure ringing and associated in-cylinder flame behaviour. In a single-cylinder small-bore optical engine, in-cylinder pressure measurement and high-speed imaging of the natural combustion luminosity have been performed. Results demonstrate that pilot injection helps reduce the in-cylinder pressure ringing by reducing the pressure rise rate of the main injection. Moreover, oscillation of the flames observed during the knocking events appears to diminish when the pilot injection is applied. How the pilot injection duration and timing affect the diesel knock behaviour is also discussed in detail.

scholarly journals Assessment on the consequences of injection strategies on combustion process and particle size distributions in Euro VI medium-duty diesel engine

2019 ◽  
Vol 21 (4) ◽  
pp. 683-697 ◽  
Author(s):  
Vicente Bermúdez ◽  
Antonio García ◽  
David Villalta ◽  
Lian Soto
Keyword(s):  
Particle Size ◽  
Diesel Engine ◽  
Size Distribution ◽  
Particle Concentration ◽  
Combustion Process ◽  
Injection Pressure ◽  
Injection Timing ◽  
Injection Parameters ◽  
Main Injection ◽  
Injection Strategies

Although there are already several works where the influence of injection parameters on exhaust emissions, and specifically on particulate matter emissions, in diesel engines has been evaluated, the diversity in the results that can be found in the literature indicates the need to carry out new experiments that can provide more information about the influence of these parameters on modern diesel engines. This study intends to be placed within this scientific framework, hence a parametric study was carried out based on the independent modification of the main injection timing and the injection pressure with respect to the nominal conditions of a new Euro VI direct injection diesel engine. Four steady-state operation points of the engine map were chosen: 25% load and 950 r/min, 50% load and 1500 r/min, 75% load and 2000 r/min and 100% load and 2200 r/min, where in each of these operation points, the variations of the injection parameters in the study on the combustion process and its consequent impact on the particle size distribution, including an analysis of the geometric mean diameter values, were evaluated. The results showed that the different injection strategies adopted, despite not significantly affecting the engine efficiency, did cause a significant impact on particle number emissions. At the low load operation, the size distribution showed a bimodal structure, and as the main injection timing was delayed and the injection pressure was decreased, the nucleation-mode particle concentration decreased, while the accumulation-mode particle concentration increased. In addition, at medium load, the nucleation-mode particle emission decreased considerably while the accumulation-mode particle emission increased, and this increase was much greater with the main injection timing delay and the injection pressure reduction. Similar behavior was observed at high load, but with a much more prominent pattern.

Sign in / Sign up

Export Citation Format

Share Document