scholarly journals Wavelet Analysis of the Effect of Injection Strategies on Cycle to Cycle Variation GDI Optical Engine under Clean and Fouled Injector

Processes ◽  
2019 ◽  
Vol 7 (11) ◽  
pp. 817
Author(s):  
Omar I. Awad ◽  
Zhou Zhang ◽  
Mohammed Kamil ◽  
Xiao Ma ◽  
Obed Majeed Ali ◽  
...  
Keyword(s):  
Complex Dynamics ◽  
Control Strategies ◽  
Injection Pressure ◽  
Injection Timing ◽  
Cyclic Variation ◽  
Optical Engine ◽  
Injection Duration ◽  
Cycle Variation ◽  
Short Period ◽  
Injection Strategies

High fluctuation in cyclic variations influences engine combustion negatively, leading to higher fuel consumption, lower performance, and drivability problems. This paper examines the impacts of injection strategies (injection pressure, injection timing and injection duration) on the cyclic variation of gasoline spark ignition (SI) optical engine under clean and fouled injectors. The principal oscillatory modes of the cycle to cycle variation have been identified, and the engine cycles over which these modes may persist are described. Through the wavelet power spectrum, the presence of short, intermediate and long-term periodicities in the pressure signal have been detected. It was noticed that depending on the clean and fouled injector, the long and intermediate-term periodicities may span many cycles, whereas the short-period oscillations tend to appear intermittently. Information of these periodicities could be helpful to promote efficient control strategies for better combustion. The outcomes report that the cyclic variation of the IMEP happens on multiple timescales, and thus, display complex dynamics. As the fouled injector used, mainly intermittent high-frequency fluctuations are recognized.

The Effects of Injection Parameters on the Performance of Common Rail Light Duty Engine Fueled with Palm Oil Biodiesel

2013 ◽  
Vol 465-466 ◽  
pp. 322-326 ◽  
Author(s):  
M. Adlan Abdullah ◽  
Farid Nasir Ani ◽  
Masjuki Hassan
Keyword(s):  
Diesel Engine ◽  
Palm Oil ◽  
Fuel Economy ◽  
Fuel Injection ◽  
Control Strategies ◽  
Engine Performance ◽  
Common Rail ◽  
Injection Timing ◽  
Injection Duration ◽  
Injection Parameters

It is in the interest of proponents of biodiesel to increase the utilization of the renewable fuel. The similarities of the methyl ester properties to diesel fuel and its miscibility proved to be an attractive advantage. It is however generally accepted that there are some performance and emissions deficit when a diesel engine is operated with biodiesel. There are research efforts to improve the diesel engine design to optimize the combustion with biodiesel. Since the common rail engines operates on flexible injection strategies, there exist an opportunity to improve engine performance and offset the fuel economy deficit by means of optimizing the engine control strategies. This approach may prove to be more practical and easily implemented. This study investigated the effects of the fuel injection parameters - rail pressure, injection duration and injection timing - on a common rail passenger car engine in terms of the fuel economy. Palm oil based biodiesel up to 30% blend in diesel was used in this study. The end of injection, (EOI), was found to be the most important parameter for affecting fuel consumption and thermal efficiency.

scholarly journals Assessment on the consequences of injection strategies on combustion process and particle size distributions in Euro VI medium-duty diesel engine

2019 ◽  
Vol 21 (4) ◽  
pp. 683-697 ◽  
Author(s):  
Vicente Bermúdez ◽  
Antonio García ◽  
David Villalta ◽  
Lian Soto
Keyword(s):  
Particle Size ◽  
Diesel Engine ◽  
Size Distribution ◽  
Particle Concentration ◽  
Combustion Process ◽  
Injection Pressure ◽  
Injection Timing ◽  
Injection Parameters ◽  
Main Injection ◽  
Injection Strategies

Although there are already several works where the influence of injection parameters on exhaust emissions, and specifically on particulate matter emissions, in diesel engines has been evaluated, the diversity in the results that can be found in the literature indicates the need to carry out new experiments that can provide more information about the influence of these parameters on modern diesel engines. This study intends to be placed within this scientific framework, hence a parametric study was carried out based on the independent modification of the main injection timing and the injection pressure with respect to the nominal conditions of a new Euro VI direct injection diesel engine. Four steady-state operation points of the engine map were chosen: 25% load and 950 r/min, 50% load and 1500 r/min, 75% load and 2000 r/min and 100% load and 2200 r/min, where in each of these operation points, the variations of the injection parameters in the study on the combustion process and its consequent impact on the particle size distribution, including an analysis of the geometric mean diameter values, were evaluated. The results showed that the different injection strategies adopted, despite not significantly affecting the engine efficiency, did cause a significant impact on particle number emissions. At the low load operation, the size distribution showed a bimodal structure, and as the main injection timing was delayed and the injection pressure was decreased, the nucleation-mode particle concentration decreased, while the accumulation-mode particle concentration increased. In addition, at medium load, the nucleation-mode particle emission decreased considerably while the accumulation-mode particle emission increased, and this increase was much greater with the main injection timing delay and the injection pressure reduction. Similar behavior was observed at high load, but with a much more prominent pattern.

Numerical investigation on the impact of multiple injection strategies and spray included angles on combustion and emissions in a marine diesel engine

2021 ◽  
pp. 095440702110694
Author(s):  
Shiru Kong ◽  
Changpu Zhao ◽  
Zhishang Bian ◽  
Yujie Cai
Keyword(s):  
Injection Timing ◽  
Pilot Injection ◽  
Post Injection ◽  
Simultaneous Reduction ◽  
Included Angle ◽  
Injection Duration ◽  
Marine Diesel ◽  
Main Injection ◽  
The Impact ◽  
Injection Strategies

The computational fluid dynamical software AVL-FIRE code was used for investigating the impact of multiply injection strategies and spray included angles on combustion and emissions in a marine diesel engine. The fuel injection parameters of spray included angle and pilot injection timing with pilot-main injection, as well as post injection ratio and post injection duration angle with pilot-main-post injection, were all investigated and optimized. The results indicate that retarding pilot injection timing with pilot-main injection declines high temperature region, resulting in a notable reduction in NOx emissions. Since fuel evaporation and burn are hampered by long spray penetration due to low temperature and pressure with pilot injection, a suitable spray included angle are used to offer more efficient air-fuel mixing process. A wider spray included angle simultaneously reduces soot emission and indicated specific fuel consumption (ISFC). Post injection fuel exerts impact on combustion process by causing a great disturbance to flow field during post combustion. Increasing post injection ratio from 4% to 10% at a small post injection duration angle great emission performance is achieved by simultaneous reduction in NOx and soot emissions while only using a slight consumption of ISFC. To summarize, the defeat of traditional NOx-soot trade-off occurs as both NOx and soot emissions are decreased with optimized multiple injection strategy and spray included angle. Particularly, there are respectively four cases with pilot-main injection and two cases with pilot-main-post injection, that achieve simultaneous reduction in NOx emissions, soot emission, and ISFC, compared to the prototype.

Low-Temperature Combustion Within a HSDI Diesel Engine Using Multiple-Injection Strategies

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
Tiegang Fang ◽  
Robert E. Coverdill ◽  
Chia-Fon F. Lee ◽  
Robert A. White
Keyword(s):  
Low Temperature ◽  
Heat Release ◽  
Injection Pressure ◽  
Diffusion Combustion ◽  
Injection Timing ◽  
Low Temperature Combustion ◽  
Conventional Combustion ◽  
Main Injection ◽  
Temperature Combustion ◽  
Injection Strategies

Low-temperature compression ignition combustion employing multiple-injection strategies in an optical high-speed direct injection diesel engine was investigated. Heat release characteristics were analyzed. The whole cycle combustion process was visualized by imaging the natural flame luminosity. The NOx emissions were measured in the exhaust pipe. The effects of the pilot injection timing, pilot fuel quantity, main injection timing, operating load, and injection pressure on the combustion and emissions were studied. Low-temperature combustion modes were achieved by using a small pilot injection with an injection timing much earlier than top dead center (TDC) followed by a main injection after TDC. The results were compared with conventional diesel (diffusion) combustion for comparison purposes. A premixed-combustion-dominated heat release rate pattern was seen for all the low-temperature combustion cases, while a typical diffusion flame combustion heat release rate was obtained for the conventional combustion case. A highly luminous flame was observed for the conventional combustion condition while a much less luminous flame was seen for the low-temperature combustion cases. For the higher-load and lower injection pressure cases, liquid fuel being injected into low-temperature premixed flame was observed for certain cases. Compared with the conventional diffusion combustion, simultaneous reductions in soot and NOx were obtained for the low-temperature combustion mode under similar operating loads. For high-load conditions, higher NOx emissions were obtained due to higher in-cylinder temperatures. However, compared with the conventional combustion case, a significant reduction in soot was achieved for the high-load conditions, which shows that increasing injection pressure greatly reduces soot emissions.

Preliminary Investigation of Direct Injection Neat n-Butanol in a Diesel Engine

2013 ◽  
Author(s):  
Tadanori Yanai ◽  
Xiaoye Han ◽  
Graham T. Reader ◽  
Ming Zheng ◽  
Jimi Tjong
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Preliminary Investigation ◽  
Pressure Rise ◽  
Injection Pressure ◽  
Injection Timing ◽  
Boost Pressure ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Short Period

The characteristics of combustion, emissions, and thermal efficiency of a diesel engine with direct injection neat n-butanol were investigated. Tests were conducted on a single cylinder water-cooled four stroke direct injection diesel engine. The engine ran at a load of 6.5 ∼ 8.0 bar IMEP at 1500 rpm engine speed and the injection pressure was controlled to 900 bar. The intake boost pressure, injection timing and EGR rate were adjusted to investigate the engine performance. The test results showed that significantly longer ignition delays were possible when using butanol compared to diesel fuel. Butanol usage generally led to a rapid heat release in a short period, resulting in excessively high pressure rise rate. The pressure rise rate was reduced by retarding the injection timing. The butanol injection timing was limited by misfire and pressure rise rate. Thus, the ignition timing controllable window by injection timing was much narrower than that of diesel. The neat butanol combustion produced near zero soot and very low NOx emissions even at low EGR rate. The tests demonstrated that neat butanol had the potential to achieve ultra-low emissions. However, challenges related to reducing the pressure rise rate and improving the ignition controllability were identified.

Combustion Characteristics of Methane Direct Injection Engine Under Various Injection Timings and Injection Pressures

2016 ◽  
Author(s):  
Jingeun Song ◽  
Mingi Choi ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Direct Injection Engine ◽  
Optical Engine ◽  
Start Of Injection ◽  
Crank Angle ◽  
Injection Pressures

The performance of a methane direct injection engine was investigated under various fuel injection timings and injection pressures. A single-cylinder optical engine was used to acquire in-cylinder pressure data and flame images. An outward-opening injector was installed at the center of the cylinder head. Experimental results showed that the combustion characteristics were strongly influenced by the end of injection timing rather than the start of injection timing. Late injection enhanced the combustion speed because the short duration between the end of injection and the spark induced strong turbulence. The flame propagation speeds under various injection timings were directly compared using crank-angle-resolved sequential flame images. The injection pressure was not an important factor in the combustion; the three injection pressure cases of 0.5, 0.8, and 1.1 MPa yielded similar combustion trends. In the cases of late injection, the injection timings of which were near the Intake Valve Closing (IVC) timing, the volumetric efficiency was higher (by 4%) than in the earlier injection cases. This result implies that the methane direct injection engine can achieve higher torque by means of the late injection strategy.

scholarly journals Effect of Injection Timing and Injection Duration of Manifold Injected Fuels in Reactivity Controlled Compression Ignition Engine Operated with Renewable Fuels

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4621
Author(s):  
P. A. Harari ◽  
N. R. Banapurmath ◽  
V. S. Yaliwal ◽  
T. M. Yunus Khan ◽  
Irfan Anjum Badruddin ◽  
...  
Keyword(s):  
Nitric Oxide ◽  
Injection Timing ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Compressed Natural Gas ◽  
Reactivity Controlled Compression Ignition ◽  
Brake Thermal Efficiency ◽  
Injection Duration ◽  
Fuel Mixtures

In the current work, an effort is made to study the influence of injection timing (IT) and injection duration (ID) of manifold injected fuels (MIF) in the reactivity controlled compression ignition (RCCI) engine. Compressed natural gas (CNG) and compressed biogas (CBG) are used as the MIF along with diesel and blends of Thevetia Peruviana methyl ester (TPME) are used as the direct injected fuels (DIF). The ITs of the MIF that were studied includes 45°ATDC, 50°ATDC, and 55°ATDC. Also, present study includes impact of various IDs of the MIF such as 3, 6, and 9 ms on RCCI mode of combustion. The complete experimental work is conducted at 75% of rated power. The results show that among the different ITs studied, the D+CNG mixture exhibits higher brake thermal efficiency (BTE), about 29.32% is observed at 50° ATDC IT, which is about 1.77, 3.58, 5.56, 7.51, and 8.54% higher than D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. The highest BTE, about 30.25%, is found for the D+CNG fuel combination at 6 ms ID, which is about 1.69, 3.48, 5.32%, 7.24, and 9.16% higher as compared with the D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. At all ITs and IDs, higher emissions of nitric oxide (NOx) along with lower emissions of smoke, carbon monoxide (CO), and hydrocarbon (HC) are found for D+CNG mixture as related to other fuel mixtures. At all ITs and IDs, D+CNG gives higher In-cylinder pressure (ICP) and heat release rate (HRR) as compared with other fuel combinations.

Simulation Research on Combustion Process in a Natural Gas-Diesel Dual-Fuel Marine Engine

2014 ◽  
Vol 525 ◽  
pp. 227-231 ◽  
Author(s):  
Min Xiao ◽  
Chun Long Feng
Keyword(s):  
Natural Gas ◽  
Total Energy ◽  
Combustion Process ◽  
Power Reduction ◽  
Dual Fuel ◽  
Injection Timing ◽  
Simulation Research ◽  
Injection Duration ◽  
Medium Speed ◽  
The Right

In order to solve the problem of Diesel natural gas dual fuel engine, such as power reduction, low charging efficiency, the conception of diesel engine fueled with pilot-ignited directly-injected liquefied natural gas is put forward. On the basis of this theory, a medium speed diesel of the marine is refitted into dual fuel engine, in order to keep original power, decrease the temperature of combustion and reduce emission. The LNG injection timing, duration of LNG injection and the different ratios the pilot diesel to total energy are studied the method of AVL FIRE software. Conclusions are as follows: When the different ratios pilot diesel to total energy is 0.5%, the engine can not work; Delaying the LNG injection timing, shortening the LNG injection duration and choose the right ratios pilot diesel to total energy can reach the indicated power of original machine, and the NOx emissions level will be greatly reduced.

Investigations on performance of diesel engine by varying injection timings with design modification on piston crown

2018 ◽  
Vol 15 (5) ◽  
pp. 562-566
Author(s):  
Vijaya K. ◽  
Shailesh Palaparty ◽  
Raghavan Srinivasa ◽  
Ravi Kumar Puli
Keyword(s):  
Diesel Engine ◽  
Injection Pressure ◽  
Combustible Mixture ◽  
Injection Timing ◽  
Connecting Rod ◽  
Design Modification ◽  
Content Type ◽  
Piston Head ◽  
Piston Crown ◽  
Fuel Vaporization

Purpose Investigations are carried out with the aim of improving performance of a diesel engine with the design modification on piston crown to stimulate the uniform combustion by inducing turbulence in the incoming charge. Design/methodology/approach A stirrer is introduced at the top of the piston so as to inculcate more turbulence to the incoming charge by improving the rate of fuel vaporization. Whirling motion is created in the combustible mixture by providing rotating blades on the cavity/bowl of the reciprocating piston head. By putting a simple link mechanism, the oscillatory motion of connecting rod will rotate the blade by an angle of 60°. Findings The investigations are carried out with and without swirl piston at 17.5 compression ratio and 200 bar injection pressure by varying injection timings. Originality/value Finally, the result shows that by using the modified piston, nearly 3 per cent of efficiency increased and 31 per cent of NOx emissions are reduced compared to that of a normal piston with 80 per cent load at standard injection timing.

scholarly journals Assessment of late pilot injection effect in dual-fuel combustion

2020 ◽  
Vol 197 ◽  
pp. 06010
Author(s):  
Antonio Caricato ◽  
Antonio Paolo Carlucci ◽  
Antonio Ficarella ◽  
Luciano Strafella
Keyword(s):  
Injection Pressure ◽  
Dual Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Compression Ignition Engine ◽  
Engine Load ◽  
Pilot Fuel ◽  
Dual Fuel Combustion ◽  
Cylinder Compression ◽  
Injection Effect

In this paper, the effect of late injection on combustion and emission levels has been investigated on a single cylinder compression ignition engine operated in dual-fuel mode injecting methane along the intake duct and igniting it through a pilot fuel injected directly into the combustion chamber. During the tests, the amount of pilot fuel injected per cycle has been kept constant, while the amount of methane has been varied on three levels. Therefore, three levels of engine load have been tested, while speed has been kept constant equal to 1500rpm. Pilot injection pressure has been varied on three set points, namely 500, 1000 and 1500 bar. For each engine load and injection pressure, pilot injection timing has been swept on a very broad range of values, spanning from very advanced to very late values. The analysis of heat release rate indicates that MK-like conditions are established in dual-fuel mode with late pilot injection. In these conditions, pollutant species, and NOx levels in particular, are significantly reduced without penalization – and in several conditions with improvement – on fuel conversion efficiency.

Sign in / Sign up

Export Citation Format

Share Document