Fans arrangement analysis in oil forced air natural cooling method of power transformer radiator

2020 ◽  
pp. 095765092096224
Author(s):  
Mohammad Ali Taghikhani ◽  
Mohammad Reza Afshar
Keyword(s):  
Heat Transfer ◽  
Power Transformer ◽  
Power Transformers ◽  
Vertical Position ◽  
Vertical Mode ◽  
Cooling Method ◽  
First Case ◽  
Cooling Fans ◽  
Natural Oil ◽  
Forced Air

The cooling of radiators in power transformers employing natural oil-air forced method is the purpose of this study. Two modes used for cooling fans, namely vertical and horizontal placement, will be compared as well. Four sets of radiators have been studied in this research, and in each set, 14 fins and three fans with a diameter of half a meter have been used. The fans will be arranged such that three of them will be placed under the radiator (in vertical position) in the first case, while in the second case, they will be located in one side of the radiator (in horizontal position). The results derived from the comparisons indicate the superiority of the horizontal mode in heat transfer against the vertical mode. Furthermore, it is notable that if the internal fan is disconnected, the cooling can be enhanced with the help of some existing points in the vertical mode. The improvement in heat transfer rate can be observed through locating the vertical fans optimally, once compared to the horizontal placement. The lower reliability of the vertical mode can be detected once the side fans are disconnected, while in any cases, the heat transfer superiority is achievable for horizontal mode. That is because, the disconnection of one of the fans, leads to the negligence of the radiators major parts in the vertical mode.

Research on Heat Transfer by Fluid in Winding Region of Power Transformer

2014 ◽  
Vol 556-562 ◽  
pp. 2002-2007
Author(s):  
Yong Ming Xu ◽  
Fei Fei Wang ◽  
Meng Meng Ai ◽  
Qing Ming Yu
Keyword(s):  
Heat Transfer ◽  
Simulation Analysis ◽  
Power Transformer ◽  
Baffle Plate ◽  
Limited Volume ◽  
Fluid Field ◽  
Natural Oil ◽  
Higher Temperature ◽  
Volume Method ◽  
Transfer Properties

In this paper, a model of the winding area for a normal working oil-immersed power (180MVA, 220kV) was built to conduct the simulation analysis for heat transfer of fluid field. Based on the fundamental mechanisms of fluid mechanics, limited volume method was used to build the model of the winding area of the power transformer. The effect of the oil input velocity, the amount and the position of oil baffle plate were concluded. The reasonable method to control the temperature was purposed by analyzing the heat-transfer properties for different conditions. When the initial oil velocity was 0.3-0.4 m/s during forced oil circulation, the best heat transfer was achieved. For the natural oil circulation, inserting 3 oil baffle plates at the higher temperature winding ends, when the number of the next two oil baffle plates is 7, the heat delivery effect is best.

A Solid-State On-Load Tap Changer for the Power Transformers of 10—0.4 kV Distribution Networks

Vestnik MEI ◽  
2020 ◽  
Vol 6 (6) ◽  
pp. 82-90
Author(s):  
Dmitriy I. Panfilov ◽  
◽  
Mikhail G. Astashev ◽  
Aleksandr V. Gorchakov ◽  
◽  
...  
Keyword(s):  
Solid State ◽  
Physical Model ◽  
High Speed ◽  
Power Transformer ◽  
Voltage Control ◽  
Power Transformers ◽  
Control Algorithms ◽  
Load Voltage ◽  
Tap Changer ◽  
Load Tap Changer

The specific features relating to voltage control of power transformers at distribution network transformer substations are considered. An approach to implementing high-speed on-load voltage control of serially produced 10/0.4 kV power transformers by using a solid-state on-load tap changer (SOLTC) is presented. An example of the SOLTC circuit solution on the basis of thyristor switches is given. On-load voltage control algorithms for power transformers equipped with SOLTC that ensure high reliability and high-speed operation are proposed. The SOLTC performance and the operability of the suggested voltage control algorithms were studied by simulation in the Matlab/Simulink environment and by experiments on the SOLTC physical model. The structure and peculiarities of the used simulation Matlab model are described. The SOLTC physical model design and its parameters are presented. The results obtained from the simulating the SOLTC operation on the Matlab model and from the experiments on the SOLTS physical model jointly with a power transformer under different loads and with using different control algorithms are given. An analysis of the experimental study results has shown the soundness of the adopted technical solutions. It has been demonstrated that the use of an SOLTC ensures high-speed voltage control, high efficiency and reliability of its operation, and arcless switching of the power transformer regulating taps without load voltage and current interruption. By using the SOLTC operation algorithms it is possible to perform individual phase voltage regulation in a three-phase 0.4 kV distribution network. The possibility of integrating SOLTC control and diagnostic facilities into the structure of modern digital substations based on the digital interface according to the IEC 61850 standard is noted.

The Effect of Regulating Elements on Convective Heat Transfer along Shaped Heat Exchange Surfaces

2013 ◽  
Vol 34 (1) ◽  
pp. 5-16 ◽  
Author(s):  
Jozef Cernecky ◽  
Jan Koniar ◽  
Zuzana Brodnianska
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Cfd Simulation ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Temperature Fields ◽  
Transfer Coefficients ◽  
Heat Transfer Intensification ◽  
Heat Transfer Coefficients ◽  
Forced Air

Abstract The paper deals with a study of the effect of regulating elements on local values of heat transfer coefficients along shaped heat exchange surfaces with forced air convection. The use of combined methods of heat transfer intensification, i.e. a combination of regulating elements with appropriately shaped heat exchange areas seems to be highly effective. The study focused on the analysis of local values of heat transfer coefficients in indicated cuts, in distances expressed as a ratio x/s for 0; 0.33; 0.66 and 1. As can be seen from our findings, in given conditions the regulating elements can increase the values of local heat transfer coefficients along shaped heat exchange surfaces. An optical method of holographic interferometry was used for the experimental research into temperature fields in the vicinity of heat exchange surfaces. The obtained values correspond very well with those of local heat transfer coefficients αx, recorded in a CFD simulation.

The Heating System of Agricultural Facilities Using Excess Heat Power Transformers

2020 ◽  
Vol 67 (1) ◽  
pp. 42-47
Author(s):  
Anatoliy I. Sopov ◽  
Aleksandr V. Vinogradov
Keyword(s):  
System Design ◽  
Heat Supply ◽  
Cooling System ◽  
Power Transformer ◽  
Electric Heating ◽  
Heating System ◽  
Power Transformers ◽  
Large Power ◽  
Excess Heat ◽  
Power Centers

In power transformers, energy losses in the form of heat are about 2 percent of their rated power, and in transformers of large power centers reach hundreds of kilowatts. Heat is dissipated into the environment and heats the street air. Therefore, there is a need to consume this thermal energy as a source of heat supply to nearby facilities. (Research purpose) To develop methods and means of using excess heat of power transformers with improvement of their cooling system design. (Materials and methods) The authors applied following methods: analysis, synthesis, comparison, monographic, mathematical and others. They analyzed various methods for consuming excess heat from power transformers. They identified suitable heat supply sources among power transformers and potential heat consumers. The authors studied the reasons for the formation of excess heat in power transformers and found ways to conserve this heat to increase the efficiency of its selection. (Results and discussion) The authors developed an improved power transformer cooling system design to combine the functions of voltage transformation and electric heating. They conducted experiments to verify the effectiveness of decisions made. A feasibility study was carried out on the implementation of the developed system using the example of the TMG-1000/10/0.4 power transformer. (Conclusions) The authors got a new way to use the excess heat of power transformers to heat the AIC facilities. It was determined that the improved design of the power transformer and its cooling system using the developed solutions made it possible to maximize the amount of heat taken off without quality loss of voltage transformation.

Three-Dimensional Numerical Modeling of Convective Heat Transfer During Shallow-Depth Forced-Air Drying of Brown Rice Grains

2015 ◽  
Vol 33 (11) ◽  
pp. 1350-1359 ◽  
Author(s):  
Jonathan H. Perez ◽  
Fumina Tanaka ◽  
Fumihiko Tanaka ◽  
Daisuke Hamanaka ◽  
Toshitaka Uchino
Keyword(s):  
Heat Transfer ◽  
Numerical Modeling ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Three Dimensional ◽  
Brown Rice ◽  
Shallow Depth ◽  
Air Drying ◽  
Rice Grains ◽  
Forced Air

Study of power transformer loading in rural power supply systems

2021 ◽  
Vol 13 (4) ◽  
pp. 282-289
Author(s):  
I. V. Naumov ◽  
D. N. Karamov ◽  
A. N. Tretyakov ◽  
M. A. Yakupova ◽  
E. S. Fedorinovа
Keyword(s):  
Energy Efficiency ◽  
Power Supply ◽  
Rural Areas ◽  
Power Transformer ◽  
Electric Energy ◽  
Power Transformers ◽  
Electric Networks ◽  
Load Factors ◽  
Optimal Load ◽  
Supply Systems

The purpose of this study is to study the effect of loading power transformers (PT) in their continuous use on their energy efficiency on a real-life example of existing rural electric networks. It is noted that the vast majority of PT in rural areas have a very low load factor, which leads to an increase in specific losses of electric energy when this is transmitted to various consumers. It is planned to optimize the existing synchronized power supply systems in rural areas by creating new power supply projects in such a way as to integrate existing power sources and ensure the most efficient loading of power transformers for the subsequent transfer of these systems to isolated ones that receive power from distributed generation facilities. As an example, we use data from an electric grid company on loading power transformers in one of the districts of the Irkutsk region. Issues related to the determination of electric energy losses in rural PT at different numerical values of their load factors are considered. A computing device was developed using modern programming tools in the MATLAB system, which has been used to calculate and plot the dependence of power losses in transformers of various capacities on the actual and recommended load factors, as well as the dependence of specific losses during the transit of 1 kVA of power through a power transformer at the actual, recommended and optimal load factors. The analysis of specific losses of electric energy at the actual, recommended and optimal load factors of PT is made. Based on the analysis, the intervals of optimal load factors for different rated power of PT of rural distribution electric networks are proposed. It is noted that to increase the energy efficiency of PT, it is necessary to reduce idling losses by increasing the load of these transformers, which can be achieved by reducing the number of transformers while changing the configuration of 0.38 kV distribution networks.

Numerical Simulation of Heat Transfer in Laminar Natural Convection of Mixed Newtonian-Non-Newtonian and Pure Non-Newtonian Nanofluids in a Square Enclosure

2021 ◽  
pp. 1-44
Author(s):  
Ajay Vallabh ◽  
P.S. Ghoshdastidar
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Base Fluid ◽  
Volume Fraction ◽  
Numerical Study ◽  
Transfer Model ◽  
Nanoparticle Concentration ◽  
Left Wall ◽  
Square Enclosure ◽  
First Case

Abstract This paper presents a steady-state heat transfer model for the natural convection of mixed Newtonian-Non-Newtonian (Alumina-Water) and pure Non-Newtonian (Alumina-0.5 wt% Carboxymethyl Cellulose (CMC)/Water) nanofluids in a square enclosure with adiabatic horizontal walls and isothermal vertical walls, the left wall being hot and the right wall cold. In the first case the nanofluid changes its Newtonian character to Non-Newtonian past 2.78% volume fraction of the nanoparticles. In the second case the base fluid itself is Non-Newtonian and the nanofluid behaves as a pure Non-Newtonian fluid. The power-law viscosity model has been adopted for the non-Newtonian nanofluids. A finite-difference based numerical study with the Stream function-Vorticity-Temperature formulation has been carried out. The homogeneous flow model has been used for modelling the nanofluids. The present results have been extensively validated with earlier works. In Case I the results indicate that Alumina-Water nanofluid shows 4% enhancement in heat transfer at 2.78% nanoparticle concentration. Following that there is a sharp decline in heat transfer with respect to that in base fluid for nanoparticle volume fractions equal to and greater than 3%. In Case II Alumina-CMC/Water nanofluid shows 17% deterioration in heat transfer with respect to that in base fluid at 1.5% nanoparticle concentration. An enhancement in heat transfer is observed for increase in hot wall temperature at a fixed volume fraction of nanoparticles, for both types of nanofluid.

Effect of Buoyancy and Density Ratio on Heat Transfer in a Smooth Cooling Channel of a Gas Turbine Blade

2018 ◽  
Author(s):  
Mandana S. Saravani ◽  
Saman Beyhaghi ◽  
Ryoichi S. Amano
Keyword(s):  
Heat Transfer ◽  
Rotational Speed ◽  
Cfd Simulation ◽  
Density Ratio ◽  
Reynolds Numbers ◽  
Buoyancy Effect ◽  
Square Channel ◽  
First Case ◽  
Computational Fluid Dynamics Cfd ◽  
The Impact

The present work investigates the effects of buoyancy and density ratio on the thermal performance of a rotating two-pass square channel. The U-bend configuration with smooth walls is selected for this study. The channel has a square cross-section with a hydraulic diameter of 5.08 cm (2 inches). The lengths of the first and second passes are 514 mm and 460 mm, respectively. The turbulent flow enters the channel with Reynolds numbers of up to 34,000. The rotational speed varies from 0 to 600 rpm with the rotational numbers up to 0.75. For this study, two approaches are considered for tracking the buoyancy effect on heat transfer. In the first case, the density ratio is set constant, and the rotational speed is varied. In the second case, the density ratio is changed in the stationary case, and the effect of density ratio is discussed. The range of Buoyancy number along the channel is 0–6. The objective is to investigate the impact of Buoyancy forces on a broader range of rotation number (0–0.75) and Buoyancy number scales (0–6), and their combined effects on heat transfer coefficient for a channel with aspect ratio of 1:1. Several computational fluid dynamics (CFD) simulation are carried out for this study, and some of the results are validated against experimental data.

A Two-Dimensional Conjugate Heat Transfer Model for Forced Air Cooling of an Electronic Device

1989 ◽  
Vol 111 (1) ◽  
pp. 41-45 ◽  
Author(s):  
A. Zebib ◽  
Y. K. Wo
Keyword(s):  
Heat Transfer ◽  
Conjugate Heat Transfer ◽  
Electronic Device ◽  
Transfer Problem ◽  
Maximum Temperature ◽  
Transfer Model ◽  
Air Cooling ◽  
Two Dimensional ◽  
Component Design ◽  
Forced Air

Thermal analysis of forced air cooling of an electronic component is modeled as a two-dimensional conjugate heat transfer problem. The velocity field in a constricted channel is first computed. Then, for a typical electronic module, the energy equation is solved with allowance for discontinuities in the thermal conductivity. Variation of the maximum temperature with the average air velocity is presented. The importance of our approach in evaluating possible benefits due to changes in component design and the limitations of the two-dimensional model are discussed.

Sign in / Sign up

Export Citation Format

Share Document