Mechanical properties of multiwall carbon nanotubes/unidirectional carbon fiber-reinforced epoxy hybrid nanocomposites in transverse and longitudinal fiber directions

2021 ◽  
pp. 096739112098651
Author(s):  
Saeedeh Saadatyar ◽  
Mohammad Hosain Beheshty ◽  
Razi Sahraeian
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Epoxy Resin ◽  
Interlaminar Shear Strength ◽  
Lap Shear Strength ◽  
Transverse Tensile ◽  
Lap Shear ◽  
Longitudinal Fiber ◽  
Interlaminar Shear ◽  
Multiwall Carbon

Unidirectional carbon fiber-reinforced epoxy (UCFRE) is suffering from weak transverse mechanical properties and through-thickness properties. The effect of different amount (0.1, 0.3 and 0.5 phr which is proportional to 0.09, 0.27 and 0.46 wt%, respectively) of multiwall carbon nanotube (MWCNT), on transverse tensile properties, flexural strength, fracture toughness in transverse and longitudinal fiber directions, interlaminar shear strength and lap shear strength of UCFRE has been investigated. Dicyandiamide was used as a thermal curing agent of epoxy resin. MWCNT was dispersed in the epoxy resin by ultrasonic instrument and their dispersion state was investigated by scanning electron microscopy (SEM). The curing behavior of epoxy resin and its nanocomposites was assessed by differential scanning calorimetry. Results show that transverse tensile strength, modulus and strain-at-break were increased by 28.5%, 25% and 14%, respectively by adding 0.1 phr of MWCNT. Longitudinal flexural properties of UCFRE was not changed by adding different amount of MWCNT. Although longitudinal flexural strength was increased by 5% by adding 0.1 phr of MWCNT. Fracture toughness in transverse and longitudinal fiber directions was increased by 39% and 9%, respectively at 0.3 phr of MWCNT. Results also show that interlaminar shear strength and lap shear strength were increased at 0.3 phr of MWCNT by 8% and 5%, respectively. These increases in mechanical properties were due to the good adhesion of fibers to the matrix, interlocking and toughening action of MWCNT as revealed by SEM.

scholarly journals Bond Strength between Glass Fiber Fabrics and Low Water-to-Binder Ratio Mortar: Experimental Characterization

2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Daniel Bohling ◽  
Andrzej Cwirzen ◽  
Karin Habermehl-Cwirzen
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Bond Strength ◽  
Glass Fiber ◽  
Penetration Depth ◽  
Pullout Strength ◽  
Lap Shear Strength ◽  
Lap Shear ◽  
Binder Ratio ◽  
Water To Binder Ratio

Full utilization of mechanical properties of glass fiber fabric-reinforced cement composites is very limited due to a low bond strength between fibers and the binder matrix. An experimental setup was developed and evaluated to correlate the mortar penetration depth with several key parameters. The studied parameters included fresh mortar properties, compressive and flexural strengths of mortar, the fabric/mortar bond strength, fabric pullout strength, and a single-lap shear strength. Results showed that an average penetration of mortar did not exceed 100 µm even at a higher water-to-binder ratio. The maximum particle size of the used fillers should be below an average spacing of single glass fibers, which in this case was less than 20 µm to avoid the sieving effect, preventing effective penetration. The pullout strength was strongly affected by the penetration depth, while the single-lap shear strength was also additionally affected by the mechanical properties of the mortar.

scholarly journals Comparison of the Processing of Epoxy Resins in Pultrusion with Open Bath Impregnation and Closed-Injection Pultrusion

2019 ◽  
Vol 3 (3) ◽  
pp. 87 ◽  
Author(s):  
Sebastian Strauß ◽  
Andreas Senz ◽  
Jessica Ellinger
Keyword(s):  
Shear Strength ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Interlaminar Shear Strength ◽  
Time Interval ◽  
Bending Stress ◽  
Epoxy Resin System ◽  
Pot Life ◽  
Interlaminar Shear ◽  
Composite Properties

In this study, the influence of the open bath and closed-injection pultrusion (CIP) processing methods of epoxy resins on the quality of glass fiber composites was investigated. In addition to the state-of-the-art epoxy resin system with long pot life, new resin systems with short pot life have recently been developed. These systems require processing by closed-injection pultrusion. The epoxies with long pot life allow both processing variants. The experimental work was carried out with two types of injection and impregnation chambers (ii_chamber), namely with a conical and a teardrop design. Fully impregnated composites, which were used for further analyses, could be produced by using the conical ii_chamber. The composite properties of the open bath and the conical ii_chamber impregnation methods were compared. No significant influence on the bending stress could be determined; the interlaminar shear strength was up to 10% better with open bath impregnation than with ii_chamber. For the composites investigated, it was shown that the open bath and ii_chamber impregnation methods can be used to produce parts with partially comparable properties, as demonstrated for the epoxy formulation with long pot life. These results indicate that processing of epoxy systems with a short pot life is also possible by closed-injection pultrusion. Furthermore, the influence on the composite properties of the time interval between the mixing of an epoxy resin and processing in an open bath was investigated. No significant effect on the bending stress and interlaminar shear strength could be determined.

scholarly journals Surface Modification of Carbon Fibers by Grafting PEEK-NH2 for Improving Interfacial Adhesion with Polyetheretherketone

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 778 ◽  
Author(s):  
Elwathig. Hassan ◽  
Tienah. Elagib ◽  
Hafeezullah Memon ◽  
Muhuo Yu ◽  
Shu Zhu
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Carbon Fibers ◽  
Interfacial Adhesion ◽  
Mechanical Analysis ◽  
Interlaminar Shear Strength ◽  
Thermoplastic Composites ◽  
Negative Effects ◽  
Covalent Bonds ◽  
Interlaminar Shear

Due to the non-polar nature and low wettability of carbon fibers (CFs), the interfacial adhesion between CFs and the polyetheretherketone (PEEK) matrix is poor, and this has negative effects on the mechanical properties of CF/PEEK composites. In this work, we established a modification method to improve the interface between CFs and PEEK based chemical grafting of aminated polyetheretherketone (PEEK-NH2) on CFs to create an interfacial layer which has competency with the PEEK matrix. The changed chemical composition, surface morphology, surface energy, and interlaminar shear strength were investigated. After grafting, the interlaminar shear strength (ILSS) was improved by 33.4% due to the covalent bonds in the interface region, as well as having good compatibility between the interface modifier and PEEK. Finally, Dynamic Mechanical Analysis (DMA) and Scanning Electron Microscopy (SEM) observation also confirmed that the properties of the modified CF/PEEK composites interface were enhanced. This work is, therefore, a beneficial approach towards enhancing the mechanical properties of thermoplastic composites by controlling the interface between CFs and the PEEK matrix.

scholarly journals Effect of Graphene Additive on Flexural and Interlaminar Shear Strength Properties of Carbon Fiber-Reinforced Polymer Composite

2020 ◽  
Vol 4 (4) ◽  
pp. 162
Author(s):  
Mohamed Ali Charfi ◽  
Ronan Mathieu ◽  
Jean-François Chatelain ◽  
Claudiane Ouellet-Plamondon ◽  
Gilbert Lebrun
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Carbon Fiber ◽  
Flexural Strength ◽  
Interlaminar Shear Strength ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Adhesion Properties ◽  
Reinforced Polymer ◽  
Interlaminar Shear

Composite materials are widely used in various manufacturing fields from aeronautic and aerospace industries to the automotive industry. This is due to their outstanding mechanical properties with respect to their light weight. However, some studies showed that the major flaws of these materials are located at the fiber/matrix interface. Therefore, enhancing matrix adhesion properties could significantly improve the overall material characteristics. This study aims to analyze the effect of graphene particles on the adhesion properties of carbon fiber-reinforced polymer (CFRP) through interlaminar shear strength (ILSS) and flexural testing. Seven modified epoxy resins were prepared with different graphene contents. The CFRP laminates were next manufactured using a method that guarantees a repeatable and consistent fiber volume fraction with a low porosity level. Short beam shear and flexural tests were performed to compare the effect of graphene on the mechanical properties of the different laminates. It was found that 0.25 wt.% of graphene filler enhanced the flexural strength by 5%, whilst the higher concentrations (2 and 3 wt.%) decreased the flexural strength by about 7%. Regarding the ILSS, samples with low concentrations (0.25 and 0.5 wt.%) demonstrated a decent increase. Meanwhile, 3 wt.% slightly decreases the ILSS.

The mechanical performance of the laminated aluminum-epoxy/glass fiber composites containing halloysite nanotubes: An experimental investigation

2020 ◽  
pp. 152808372096073
Author(s):  
Marwa A Abd El-baky ◽  
Mohamed A Attia
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Tensile Strain ◽  
Mechanical Performance ◽  
Flexural Modulus ◽  
Halloysite Nanotubes ◽  
Interlaminar Shear Strength ◽  
Plane Shear ◽  
Bearing Strength ◽  
Interlaminar Shear

In this study, the effect of different weight percentages (wt. %) of halloysite nanotubes (HNTs) on the mechanical performance of glass laminate aluminum (Al) reinforced epoxy (GLARE) was investigated. GLARE (3/2) laminates with quasi-isotropic lay-up, [Al/[(0°/90°)/(45°/−45°)]s/Al/[(0°/90°)/(45°/−45°)]s/Al] filled with 0, 0.25, 0.5, 1, 2 and 3 wt. % of HNTs were fabricated using hand lay-up followed by compression molding. To explore the effect of HNTs on the mechanical properties, tensile, flexural, in-plane shear, interlaminar shear, bearing and impact tests were conducted. Results demonstrated that the inclusion of 1 wt. % of HNTs into GLARE leads to maximum improvements of 35.67, 8.50, 28.85, 50.47, 50.27, 30.43, 23.73, 72.08, 30.74, and 51.52% in tensile strength, tensile strain, Young's modulus, modulus of toughness, flexural strength, flexural strain, in-plane shear strength, interlaminar shear strength, bearing strength, and impact strength, respectively, compared to pristine GLARE. An enhancement of 38.89% in the flexural modulus was attained by adding 0.5 wt. % of HNTs to GLARE compared to pristine GLARE. The tensile strength, tensile strain, modulus of toughness, flexural strength, flexural modulus, flexural strain, in-plane shear strength, and interlaminar shear strength of GLARE filled with 3 wt. % of HNTs are 0.91, 0.88, 0.91, 0.91, 0.71, 0.83, 0.85, and 0.91 times those of the original GLARE. But Young’s modulus, bearing strength, and impact strength are 1.10, 1.15 and 1.20 times those of the original GLARE. To investigate the fracture mechanism, field emission scanning electron microscope (FE-SEM) and energy-dispersive X-ray spectroscopy (EDX) were used. The microscopic images revealed that adding HNTs lead to the improvement in the interaction between the epoxy matrix and glass fiber, thereby improving the mechanical properties.

Effect of Needling Parameters on Mechanical Properties of C/C Composites Reinforced by Carbon Cloth

2007 ◽  
Vol 546-549 ◽  
pp. 1521-1524
Author(s):  
Xiao Hu Zhang ◽  
He Jun Li ◽  
Zhi Biao Hao ◽  
Hong Cui
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Compression Strength ◽  
Bending Strength ◽  
Interlaminar Shear Strength ◽  
Carbon Cloth ◽  
Depth Range ◽  
Needle Punching ◽  
Interlaminar Shear

The influence of needling parameters on mechanical properties of carbon-carbon (C-C)composites reinforced by needled carbon cloth was studied in the present investigation. The results showed that needling density (ND)and needle-punching depth (PD) both had a larger effect on interlaminar shear strength (ILSS) than on compression strength and flexible strength of Needling C-C(NC-C). The mechanical properties of NC-C increased with increasing punching density in the range of 20-45 punch/cm2 and also with increasing punching depth range from10 to16mm. The NC-C with the highest ND value of 55punch/cm2 had highest ILSS value of 27 MPa.The optimized ND and PD parameters was 30 punch/cm2 and 12mm respectively, which resulted in a high value of tensile strength(119MPa), bending strength (220MPa) and compression strength (235 MPa) in the X-Y direction .

Improvement of interlaminar shear strength of 2.5D fabric laminated composites with short-cut web interlayer

2017 ◽  
Vol 37 (3) ◽  
pp. 261-269 ◽  
Author(s):  
Leilei Song ◽  
Jialu Li ◽  
Yufen Zhao ◽  
Xiaoming Chen ◽  
Li Chen
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Laminated Composites ◽  
Three Dimensional ◽  
Interlaminar Shear Strength ◽  
Bending Properties ◽  
Bending Tests ◽  
Testing Method ◽  
Short Beam ◽  
Interlaminar Shear

Abstract In this study, the short-cut web interlayer and three-dimensional (3D) needle-punched technique were used to improve the interlaminar shear strength (ILSS) of 2.5D fabric laminated composites. The ILSS was measured by the short beam testing method, and the tensile and bending tests were carried out to investigate the in-plane mechanical properties. Observations on microstructure and crack propagation were carried out. The damage mechanisms of different 2.5D fabric laminated composites were analyzed. The results showed that the short-cut web interlayer and 3D needle-punched technique resulted in the improvement of ILSS, and they affected the tensile and bending properties of 2.5D fabric laminated composites.

Sign in / Sign up

Export Citation Format

Share Document