Studying effects of joint characteristics on the performance of a cantilever beam shaped piezoelectric energy harvester through joint identification

2021 ◽  
pp. 1045389X2110639
Author(s):  
Masoud Dehand ◽  
Kamal Jahani ◽  
Morteza Sadeghi ◽  
Fred F Afagh
Keyword(s):  
Cantilever Beam ◽  
Experimental Testing ◽  
Electrical Energy ◽  
Bolted Joint ◽  
Identification Procedure ◽  
Piezoelectric Energy ◽  
Joint Characteristics ◽  
Real Coded Genetic Algorithm ◽  
Harvesting Systems ◽  
Joint Identification

In energy harvesting systems, specifications of the generated electrical energy depend on the structure’s dynamics. This dependence can be used to identify the system’s joint characteristics. To this end, an innovative frequency-response-function (FRF) based identification method is presented. The investigated system is a cantilever beam shaped structure with an embedded bimorph piezoelectric bender, connected to a base via bolted joint as a depiction for wing of a UAV connected to fuselage. The implemented FRF is ratio of the piezoelectric output voltage to the base input displacement. The joint identification procedure consists of analytical modeling of the system with joint, experimental testing of the system and a real-coded Genetic Algorithm (GA) method. The joint is modeled as a combination of longitudinal and torsional springs, whose stiffnesses are obtained using the GA method. The obtained results indicate that the analytical model has good correlation with the experimental data. Then, effects of the joint characteristics on the energy harvester’s performance are investigated by comparison of the system with two different joint assumptions, namely, rigid and realistic joint. Finally, the effects of various joint characteristics on the energy harvester’s performance are presented and approaches to achieve the maximum performance of the system are suggested.

A Creative Vibration Energy Harvesting System to Support a Self-Powered Internet of Thing (IoT) Network in Smart Bridge Monitoring

2020 ◽  
Author(s):  
Saman Farhangdoust ◽  
Claudia Mederos ◽  
Behrouz Farkiani ◽  
Armin Mehrabi ◽  
Hossein Taheri ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Average Power ◽  
Electrical Energy ◽  
Laser Vibrometer ◽  
Stay Cable ◽  
Fe Modelling ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
Energy Harvesting System

Abstract This paper presents a creative energy harvesting system using a bimorph piezoelectric cantilever-beam to power wireless sensors in an IoT network for the Sunshine Skyway Bridge. The bimorph piezoelectric energy harvester (BPEH) comprises a cantilever beam as a substrate sandwiched between two piezoelectric layers to remarkably harness ambient vibrations of an inclined stay cable and convert them into electrical energy when the cable is subjected to a harmonic acceleration. To investigate and design the bridge energy harvesting system, a field measurement was required for collecting cable vibration data. The results of a non-contact laser vibrometer is used to remotely measure the dynamic characteristics of the inclined cables. A finite element study is employed to simulate a 3-D model of the proposed BPEH by COMSOL Multiphasics. The FE modelling results showed that the average power generated by the BPEH excited by a harmonic acceleration of 1 m/s2 at 1 Hz is up to 614 μW which satisfies the minimum electric power required for the sensor node in the proposed IoT network. In this research a LoRaWAN architecture is also developed to utilize the BPEH as a sustainable and sufficient power resource for an IoT platform which uses wireless sensor networks installed on the bridge stay cables to collect and remotely transfer bridge health monitoring data over the bridge in a low-power manner.

Embedded Metamaterial Subframe Patch for Increased Power Output of Piezoelectric Energy Harvesters

2021 ◽  
pp. 1-9
Author(s):  
Saman Farhangdoust ◽  
Gary Georgeson ◽  
Jeong-Beom Ihn ◽  
Armin Mehrabi
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Renewable Energy Sources ◽  
Piezoelectric Element ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Harvesting Systems ◽  
Host Structure ◽  
Self Powered ◽  
Low Efficiency

Abstract These days, piezoelectric energy harvesting (PEH) is introduced as one of the clean and renewable energy sources for powering the self-powered sensors utilized for wireless condition monitoring of structures. However, low efficiency is the biggest drawback of the PEHs. This paper introduces an innovative embedded metamaterial subframe (MetaSub) patch as a practical solution to address the low throughput limitation of conventional PEHs whose host structure has already been constructed or installed. To evaluate the performance of the embedded MetaSub patch (EMSP), a cantilever beam is considered as the host structure in this study. The EMSP transfers the auxetic behavior to the piezoelectric element (PZT) wherever substituting a regular beam with an auxetic beam is either impracticable or suboptimal. The concept of the EMSP is numerically validated, and the COMSOL Multiphysics software was employed to investigate its performance when a cantilever beam is subjected to different amplitude and frequency. The FEM results demonstrate that the harvesting power in cases that use the EMSP can be amplified up to 5.5 times compared to a piezoelectric cantilever energy harvester without patch. This paper opens up a great potential of using EMSP for different types of energy harvesting systems in biomedical, acoustics, civil, electrical, aerospace, and mechanical engineering applications.

scholarly journals Design and Analysis of Piezoelectric Energy Harvesting Systems

2019 ◽  
Vol 8 (9) ◽  
pp. 2249-2257
Keyword(s):  
Duty Cycle ◽  
Power Flow ◽  
Vibrational Energy ◽  
Piezoelectric Materials ◽  
Piezoelectric Element ◽  
Electrical Energy ◽  
Nonlinear Process ◽  
Power Relationship ◽  
Piezoelectric Energy ◽  
Harvesting Systems

This Paper presents a new technique of electrical energy generation using mechanically excited piezoelectric materials and a nonlinear process. This technique, called double synchronized switch harvesting (DSSH), is derived from the synchronized switch damping (SSD), which is a nonlinear technique previously developed to address the problem of vibration damping on mechanical structures. This technique results in a significant increase of the electromechanical conversion capability of piezoelectric materials. An optimized method of harvesting vibrational energy with a piezoelectric element using a dc–dc converter is presented. In this configuration, the converter regulates the power flow from the piezoelectric element to the desired electronic load. Analysis of the converter in discontinuous current conduction mode results in an expression for the duty cycle-power relationship. Using parameters of the mechanical system, the piezoelectric element, and the converter; the “optimal” duty cycle can be determined where the harvested power is maximized for the level of mechanical excitation. A circuit is proposed which implements this relationship, and experimental results show that the converter increases the harvested power by approximately 365% as compared to when the dc–dc converter is not used

scholarly journals Numerical Modelling of a Piezo Roof Harvesting System: The Right Component Selection

2017 ◽  
Vol 64 (2) ◽  
pp. 257-282
Author(s):  
Romeo Di Leo ◽  
Massimo Viscardi ◽  
Francesco Paolo Tuccinardi ◽  
Michele Visone
Keyword(s):  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Final Choice ◽  
Component Selection ◽  
Piezoelectric Energy ◽  
Harvesting Systems ◽  
Energy Harvesting System ◽  
Definition Of ◽  
Piezoelectric Structures ◽  
The Right

Abstract The present work focuses on a first study for a piezoelectric harvesting system, finalized to the obtaining of electrical energy from the kinetic energy of rainy precipitation, a renewable energy source not really considered until now. The system, after the realization, can be collocated on the roof of an house, configuring a “Piezo Roof Harvesting System”. After presenting a state of art of the harvesting systems from environmental energy, linked to vibrations, using piezoelectric structures, and of piezoelectric harvesting systems functioning with rain, the authors propose an analysis of the fundamental features of rainy precipitations for the definition of the harvesting system. Then, four key patterns for the realization of a piezoelectric energy harvesting system are discussed and analysed, arriving to the choice of a cantilever beam scheme, in which the piezoelectric material works in 31 mode. An electro-mechanical model for the simulation of performance of the unit for the energetic conversion, composed of three blocks, is proposed. The model is used for a simulation campaign to perform the final choice of the more suitable piezoelectric unit, available on the market, which will be adopted for the realization of the “Piezo Roof Harvesting System”.

scholarly journals Characterization of Polyvinylidene Difluoride-based Energy Harvesting with IDE Circuit Flexible Cantilever Beam

2022 ◽  
Vol 30 (1) ◽  
pp. 605-619
Author(s):  
Khairul Azman Ahmad ◽  
Noramalina Abdullah ◽  
Mohamad Faizal Abd Rahman ◽  
Muhammad Khusairi Osman ◽  
Rozan Boudville
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Cantilever Beam ◽  
Energy Harvester ◽  
Electrical Energy ◽  
Adhesive Tape ◽  
Induced Voltage ◽  
Interdigitated Electrode ◽  
Polyvinylidene Difluoride ◽  
Piezoelectric Energy

Piezoelectric energy harvesting is the process of extracting electrical energy using energy harvester devices. Any stress in the piezoelectric material will generate induced voltage. Previous energy harvester device with stiff cantilever beam was generated low harvested energy. A flexural piezoelectric energy harvester is proposed to improve the generated harvesting energy. Polyvinylidene difluoride is a polymer piezoelectric material attached to a flexible circuit made of polyimide. Four interdigitated electrode circuits were designed and outsourced for fabrication. The polyvinylidene difluoride was then attached to the interdigitated electrode circuit, and a single clear adhesive tape was used to bind them. Four piezoelectric energy harvesters and ultrasonic ceramic generators were experimentally tested using a sieve shaker. The sieve shaker contains a two-speed oscillator, with M1=0.025 m/s and M2=0.05 m/s. It was used to oscillate the energy harvester devices. The resulting induced voltages were then measured. Design 4, with the widest width of electrode fingers and the widest gap between electrode fingers, had the highest power generated at an output load of 0.745 µW with the M2 oscillation speed. The oscillation speed of the sieve shaker impacted the energy harvester devices as a higher oscillation speed gave higher generated power.

High-output piezoelectric energy harvester using tapered beam with cavity

2017 ◽  
Vol 29 (5) ◽  
pp. 800-815 ◽  
Author(s):  
S Srinivasulu Raju ◽  
M Umapathy ◽  
G Uma
Keyword(s):  
Analytical Model ◽  
Cantilever Beam ◽  
Energy Harvester ◽  
Structural Parameters ◽  
Beam Theory ◽  
Electrical Energy ◽  
Tapered Beam ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Structure

Energy harvesting using cantilever-based piezoelectric structure is most popular for harvesting electrical energy from ambient vibrations. Efforts are also made to maximize the harvester power by means of tailoring the structural parameters of the cantilever beam. This article proposes a method to maximize the harvester voltage from the cantilever-based piezoelectric energy harvester by means of tailoring the structure of the cantilever, to have a tapering in width, thickness and in both width and thickness (double taper). It is also proposed to introduce rectangular and trapezoidal cavities in the tapered energy harvesters to further maximize the harvester voltage. The analytical model of the proposed harvesters is developed using Euler–Bernoulli beam theory, and its free vibration solution is analysed using Bessel functions. The energy harvesters are fabricated and experimentally evaluated for its performance. It is concluded from the results of analytical model and experimentation that width, thickness and double-tapered beam increases the harvester voltage by 35.6%, 84.8% and 126.6%, respectively, as compared to the energy harvester designed with uniform cantilever beam. Among all the energy harvesters proposed in this article, the maximum voltage is generated from the double-tapered beam with trapezoidal cavity. The experimental results are in close agreement with the results obtained from the analytical model.

Harvesting Vibration Energy for Structural Health Monitoring in Aircraft

2009 ◽  
Vol 413-414 ◽  
pp. 439-446 ◽  
Author(s):  
C.A. Featherston ◽  
Karen M. Holford ◽  
Bea Greaves
Keyword(s):  
Structural Health Monitoring ◽  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Health Monitoring ◽  
Electrical Energy ◽  
Lead Zirconate ◽  
Body Motion ◽  
Structural Health ◽  
Piezoelectric Energy ◽  
Harvesting Systems

The concept of harvesting energy is not a new one: there has been an interest in this area for around 10 years. Devices typically use either vibration (rigid body motion) or thermal gradients and can harvest sufficient energy to power telemetry, small devices or to charge a battery or capacitance device. However, for the new generation of aircraft, (both fixed wing and rotating) there is now an urgent need to develop energy harvesting systems in order to provide localised power for sensors in structural health monitoring systems (SHM). By implementing SHM, aircraft manufacturers can benefit from improved safety, reduced maintenance and extended aircraft life. The work presented examines the feasibility of designing an energy harvesting system powered by the vibrations of aircraft panels generated in flight. PZT (lead zirconate titanate) harvesters are bonded to an aluminium alloy panel, representative of an aircraft wing panel which is vibrated across a range of amplitudes (up to + 0.2mm) and frequencies (up to 300Hz). By recording voltage and current outputs from each harvester, generated power is calculated which when normalised for area and mass indicates values of up to 7.0 Wm-2 and 2.5Wkg-1 respectively, representing mechanical to electrical energy conversion efficiencies of up to 35% dependant on frequency of vibration. From these values it is estimated that a harvester area of down to 71cm2 or mass of as little as 20g is necessary to meet the current minimum power requirements of SHM systems of 50mW. With predicted reductions in sensor power consumption indicating system power requirements in the order of 0.1-1mW, this work shows that piezoelectric energy harvesting has future potential for powering aerospace SHM systems.

Multimodal pizza-shaped piezoelectric vibration-based energy harvesters

2021 ◽  
pp. 1045389X2110069
Author(s):  
Virgilio J Caetano ◽  
Marcelo A Savi
Keyword(s):  
Energy Harvesting ◽  
Frequency Spectrum ◽  
Optimization Procedure ◽  
Single Mode ◽  
Ambient Vibration ◽  
Vibration Source ◽  
Element Analysis ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Harvesting Systems

Energy harvesting from ambient vibration through piezoelectric devices has received a lot of attention in recent years from both academia and industry. One of the main challenges is to develop devices capable of adapting to diverse sources of environmental excitation, being able to efficiently operate over a broadband frequency spectrum. This work proposes a novel multimodal design of a piezoelectric energy harvesting system to harness energy from a wideband ambient vibration source. Circular-shaped and pizza-shaped designs are employed as candidates for the device, comparing their performance with classical beam-shaped devices. Finite element analysis is employed to model system dynamics using ANSYS Workbench. An optimization procedure is applied to the system aiming to seek a configuration that can extract energy from a broader frequency spectrum and maximize its output power. A comparative analysis with conventional energy harvesting systems is performed. Numerical simulations are carried out to investigate the harvester performances under harmonic and random excitations. Results show that the proposed multimodal harvester has potential to harness energy from broadband ambient vibration sources presenting performance advantages in comparison to conventional single-mode energy harvesters.

Modelling of Broadband Piezoelectric Energy Harvesters

2012 ◽  
Author(s):  
Shengxi Zhou ◽  
Junyi Cao ◽  
Jing Lin ◽  
Chengbin Ma
Keyword(s):  
Magnetic Force ◽  
Wide Spectrum ◽  
Magnetic Coupling ◽  
Experimental System ◽  
Polynomial Equation ◽  
Coupling Model ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Harvesting Systems ◽  
Piezoelectric Cantilevers

A nonlinear magnetic coupling model for piezoelectric energy harvesting systems is proposed in this paper. For the purpose of enhancing harvesting efficiency from wide-spectrum vibrations, a magnetic coupling structure of piezoelectric cantilevers is presented. However, the nonlinear dynamic of broadband piezoelectric energy harvesters could not be adequately described due to complex nonlinear magnetic force. Furthermore, the broken frequency can not be predicted using the designed dimensionless model. In order to solve those issues, the nonlinear magnetic force is established using polynomial equation. Based on Hamilton principle and finite element theory, a nonlinear model of the standard piezoelectric cantilever with magnetic coupling is established. Frequency sweeping experiments with various excitation are carried out. The results show that the output characteristic of the proposed model is approximate to that of experimental system under the same condition, and also their broken frequency is very close.

Sign in / Sign up

Export Citation Format

Share Document