Experimental and numerical study of reinforced concrete beams with steel fibers subjected to impact loading

2017 ◽  
Vol 27 (7) ◽  
pp. 1058-1083 ◽  
Author(s):  
Liu Jin ◽  
Renbo Zhang ◽  
Guoqin Dou ◽  
Jiandong Xu ◽  
Xiuli Du
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Impact Loading ◽  
Impact Force ◽  
Numerical Study ◽  
Reaction Force ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
The Impact

As a kind of impact resistant material, steel fiber reinforced concrete (SFRC) has a good ductility and energy dissipation capacity by improving the tensile strength and impact toughness. To explore the dynamic mechanical behavior of SFRC beams subjected to impact loading, 12 simply-supported SFRC beams with different stirrup ratios (0%, 0.253% and 0.502%) and different volume fractions of steel fibers (0%, 1%, 2% and 3%) were tested with free-falling drop-weights impacting at the mid-span of specimens. The failure patterns were observed and videoed, and simultaneously, the time histories of the impact force, the reaction force, and the mid-span deflection were recorded. Moreover, the influences of stirrup ratio and volume fraction of steel fibers on the impact resistant behavior of the SFRC beams were preliminarily analyzed and discussed. The results indicate that the impact resistant performance of SFRC beams, such as crack pattern, ductility, energy consumption capacity, and deformation recovery capacity can be improved by the addition of steel fibers and stirrups. The required static capacity of these beams were calculated based on the analysis of reaction force vs. displacement loop and impact force vs. displacement loop as well as absorbed energy ratio. For further understanding the experimental results, finite element simulation of SFRC beams subjected to impact loading were carried out. The rationality and accuracy of the finite element model was illustrated by the good agreement between the test observations and the numerical results.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

Study on Retrofitting and Strengthening of Reinforced Concrete Beams Using Fibrous Concrete

2021 ◽  
Vol 9 (8) ◽  
pp. 1676-1684
Author(s):  
Natalia Sharma
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Cement Matrix ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete

Abstract: Reinforced concrete structures are frequently in need of repair and strengthening as a result of numerous environmental causes, ageing, or material damage under intense stress conditions, as well as mistakes made during the construction process. RC structures are repaired using a variety of approaches nowadays. The usage of FRC is one of the retrofitting strategies. Steel fiber reinforced concrete (SFRC) was used in this investigation because it contains randomly dispersed short discrete steel fibers that operate as internal reinforcement to improve the cementitious composite's characteristics (concrete). The main rationale for integrating small discrete fibers into a cement matrix is to reduce the amount of cement used. The principal reason for incorporating short discrete fibers into a cement matrix is to reduce cracking in the elastic range, increase the tensile strength and deformation capacity and increase the toughness of the resultant composite. These properties of SFRC primarily depend upon length and volume of Steel fibers used in the concrete mixture. In India, the steel fiber reinforced concrete (SFRC) has seen limited applications in several structures due to the lack of awareness, design guidelines and construction specifications. Therefore, there is a need to develop information on the role of steel fibers in the concrete mixture. The experimental work reported in this study includes the mechanical properties of concrete at different volume fractions of steel fibers. These mechanical properties include compressive strength, split tensile strength and flexural strength and to study the effect of volume fraction and aspect ratio of steel fibers on these mechanical properties. However, main aim of the study was significance of reinforced concrete beams strengthened with fiber reinforced concrete layer and to investigate how these beams deflect under strain. The objective of the investigation was finding that applying FRC to strengthen beams enhanced structural performance in terms of ultimate load carrying capacity, fracture pattern deflection, and mode of failure or not.

Repair of Severely Damaged Reinforced Concrete Beams with High-Strength Cementitious Grout

2020 ◽  
Vol 2674 (6) ◽  
pp. 372-384
Author(s):  
Antoine N. Gergess ◽  
Mahfoud Shaikh Al Shabab ◽  
Razane Massouh
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Cementitious Materials ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Rc Beams ◽  
Rc Structures

High-strength cementitious materials such as high-performance concrete are extensively used for retrofit of reinforced concrete (RC) structures. The effectiveness of these materials is increased when mixed with steel fibers. A commonly used technique for strengthening and repair of RC beams consists of applying high-performance fiber-reinforced concrete jackets around the beam perimeter. This paper investigates the jacketing method for repairing severely damaged RC beams. Four 2 m (6 ft 63/4 in.) long rectangular RC beams, 200 × 300 mm (8 ×12 in.) were initially cast and loaded until failure based on three-point bending tests. The four beams were then repaired by thickening the sides of the damaged RC beams using a commercially available high-strength shrinkage grout with and without steel fibers. Strain and deformation were recorded in the damaged and repaired beams to compare structural performance. It is shown that the flexural strength of the repaired beams is increased and the crack pattern under loading is improved, proving that the proposed repair method can restore the resistance capacity of RC beams despite the degree of damage. A method for repair is proposed and an analytical investigation is also performed to understand the structural behavior of the repaired beams based on different thickening configurations.

The Study on Carbon Fiber Reinforced Concrete Beams Based on Finite Element Analysis

2012 ◽  
Vol 430-432 ◽  
pp. 331-336
Author(s):  
Jian Hua Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Carbon Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Concrete ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced ◽  
Element Analysis ◽  
Carbon Fiber Reinforced

Carbon fiber-reinforced polymer (CFRP) sheets have recently become popular for use as repair or rehabilitation material for deteriorated carbon fiber reinforced concrete structures. Carbon fiber reinforced concrete beams were analyzed by finite element software ANASYS. Through the finite element analysis, the results showed that using bonded CFRP to strengthen R. C. beams can significantly increase their load carrying capacity. However, the beams with prestressed CFRP can withstand larger ultimate loads than beams with bonded CFRP. Using bonded CFRP to strengthen R. C. beams can obviously reduce the ultimate deflection.

Effect of cracking localization on the structural ductility of normal strength and high strength reinforced concrete beams with steel fibers

2019 ◽  
Vol 10 (4) ◽  
pp. 457-469 ◽  
Author(s):  
Avraham N Dancygier ◽  
Yuri S Karinski
Keyword(s):  
Reinforced Concrete ◽  
Transition Point ◽  
Concrete Beams ◽  
High Strength ◽  
Reinforcement Ratio ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Flexural Ductility ◽  
Ductility Ratio ◽  
The Impact

This article presents a study of cracking localization in normal and high strength concrete beams that include steel fibers and the influence of this localization on their structural ductility. It is shown that for a given fiber type and content, as the reinforcement ratio ρ decreases, the cracking localization level increases. The effect of ρ on the level of cracking localization is more pronounced for low amounts of conventional reinforcement. This range of conventional reinforcement ratio is typical of slabs and especially for the commonly thicker protective slabs. Examination of the effect of the reinforcement ratio on the flexural ductility shows that there exists a transition point below which the ductility ratio decreases with  ρ. This transition point is well above the minimum reinforcement ratio, which is required in design codes for plain reinforced concrete elements. Empirical analysis of the relation between cracking localization and ductility ratio shows that up to the same transition point, as cracking localization increases, the flexural ductility decreases. Findings of this study show that the positive effect of adding fibers on enhancing the impact resistance of slabs and beams is conflicted by their negative influence on reducing the structural ductility for low reinforcement ratios, which are typical of protective slabs.

scholarly journals Design of reinforced concrete beams with steel fibers in the ultimate limit state

2018 ◽  
Vol 11 (5) ◽  
pp. 997-1024
Author(s):  
T. E. T. BUTTIGNOL ◽  
J. F. FERNANDES ◽  
T. N. BITTENCOURT ◽  
J. L. A. O. SOUSA
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Limit State ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Experimental Results ◽  
Reinforced Concrete Beams ◽  
Ultimate Limit State ◽  
Bending Tests

Abstract This paper carries out a design analysis of reinforced concrete beams with steel fibers following the fib Model Code 2010 (MC 2010) procedures. The values obtained from the design calculations are compared with the experimental results of reinforced concrete beams with 20kg/m3 and 60 kg/m3 of steel fibers submitted to four-point bending tests. In the first part, the procedures for the classification and characterization of the material are explained. The experimental results of three-point bending tests performed on notched steel fiber reinforced concrete (FRC) beams following EN 14651 procedures are described. Moreover, the characterization of the FRC beams according to MC 2010, are carried out. In the second part, the flexural design of reinforced concrete beams with steel fibers, according to MC 2010, is carried out. A sectional analysis is performed in order to obtain the moment-curvature and the force-vertical displacement curves. The theoretical values are compared with the experimental results. Besides, a linear statistic analysis by means of the Rule of Mixture is carried out in order to analyze the variation of the flexural capacity of the reinforced beams with different amounts of steel fibers. The results demonstrated that the design rules described in the MC 2010 are on the safe side. The flexural resistance of concretes with different amounts of fiber incorporation can be determined by the Rule of Mixture, which has shown a high correlation factor (R2) with the experimental values.

Damage Behavior of Steel Fiber Reinforced and Polymer Modified Concrete under Impact Loading

2007 ◽  
Vol 348-349 ◽  
pp. 889-892 ◽  
Author(s):  
Yi Ping Liu ◽  
Li Qun Tang ◽  
Xiao Qing Huang
Keyword(s):  
Impact Loading ◽  
Damage Evolution ◽  
Steel Fiber ◽  
Split Hopkinson Pressure Bar ◽  
Early Stage ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Polymer Modified Concrete ◽  
The Impact

Damage behaviors of plain concrete (PC), steel fiber reinforced concrete (SFRC), steel fiber reinforced and polymer modified concrete (SFRPMC) are studied in this paper by use of a Split Hopkinson Pressure Bar (SHPB). Three kinds of concrete materials appear obvious strain rate strengthening effects. SFRPMC appears a better resistance and energy absorption ability. A rate-dependent damage model is suggested to depict the impact damage evolution of three kinds of materials under different impact velocities. The simulation results showed the theoretical model could well describe the dynamic behaviors of the three kinds of materials, and steel fibers attribute more to resist crack develop in early stage, “bridge effect” of steel fibers slow up the damage evolution in SFRC, with the addition of polymer, the internal structures of SFRPMC were modified, SFRPMC gains better ductility, and appears a kind of “softening effect”, which makes the damage in SFRPMC develop more slowly than that in PC and SFRC under impact loading.

Sign in / Sign up

Export Citation Format

Share Document