Textile-reinforced mortars; an experimental comparative study of tensile strength improvement methods

2022 ◽  
pp. 146442072110682
Author(s):  
Roohallah Ghasemi ◽  
Majid Safarabadi ◽  
Mojtaba Haghighi-Yazdi ◽  
Abolfazl Mirdehghan
Keyword(s):  
Experimental Study ◽  
Tensile Strength ◽  
Short Fiber ◽  
Tensile Behavior ◽  
Short Fibers ◽  
Method Performance ◽  
Interface Modification ◽  
Effective Factors ◽  
One Way Anova ◽  
Strength Improvement

In this article, an experimental study is conducted to compare eight improvement methods for the tensile strength of textile-reinforced mortars (TRM). 12 series of samples with different modification methods are compared to determine the most effective factors on crack initiation force and tensile strength of TRM. Eight modification methods are categorized under three main groups of mortar modification, fabric modification, and fabric-mortar interface modification. TRM's first crack force and ultimate force are considered as indices of method performance. One-way ANOVA and factorial analysis were also conducted to statically determine the most significant methods for improving TRM tensile behavior. The results showed that the modification of mortar by short fiber is the most effective method for the enhancement of TRM's first crack force. Also, the methods which led to the transfer of failure mode from mortar to fabrics were the most effective methods on TRM ultimate force improvement. The result showed that coating fabrics with epoxy affects TRM tensile strength more than all other methods. Extra enhancement of TRM ultimate force is achieved by adding silica fume to epoxy before coating the fabrics and spreading the sand and short fibers on impregnated fabrics.

scholarly journals A numerical and experimental study on the tensile behavior of plasma shocked granite under dynamic loading

2017 ◽  
Vol 50 (2) ◽  
pp. 41-62
Author(s):  
Ahmad Mardoukhi ◽  
Timo Saksala ◽  
Mikko Hokka ◽  
Veli-Tapani Kuokkala
Keyword(s):  
Experimental Study ◽  
Tensile Strength ◽  
Mechanical Behavior ◽  
Thermal Shock ◽  
Dynamic Loading ◽  
Split Hopkinson Pressure Bar ◽  
Tensile Behavior ◽  
Brazilian Disc ◽  
Brazilian Disc Test ◽  
Plasma Shock

This paper presents a numerical and experimental study on the mechanical behavior of plasma shocked rock. The dynamic tensile behavior of plasma shock treated Balmoral Red granite was studied under dynamic loading using the Brazilian disc test and the Split Hopkinson Pressure Bar device. Different heat shocks were produced on the Brazilian disc samples by moving the plasma gun over the sample at different speeds. Microscopy clearly showed that as the duration of the thermal shock increases, the number of the surface cracks and their complexity increases (quantified here as the fractal dimension of the crack patterns) and the area of the damaged surface grows larger as well. At the highest thermal shock duration of 0.80 seconds the tensile strength of the Brazilian disc sample drops by approximately 20%. In the numerical simulations of the dynamic Brazilian disc test, this decrease in tensile strength was reproduced by modeling the plasma shock induced damage using the embedded discontinuity finite element method. The damage caused by the plasma shock was modeled by two methods, namely by pre-embedded discontinuity populations with zero strength and by assuming that the rock strength is lowered and conform to the Weibull distribution. This paper presents a quantitative assessment of the effects of the heat shock, the surface microstructure and mechanical behavior of the studied rock, and a promising numerical model to account for the pre-existing crack distributions in a rock material.

Experimental Study on Manufacturing Process of Short Fiber-Rubber Composite Material Using New Type Six-Wing Synchronous Rotor

2009 ◽  
Vol 87-88 ◽  
pp. 317-322
Author(s):  
De Wei Zhang ◽  
Chuan Sheng Wang
Keyword(s):  
Experimental Study ◽  
Composite Material ◽  
Manufacturing Process ◽  
Short Fiber ◽  
Short Fibers ◽  
Rubber Composite ◽  
New Type ◽  
Mechanical Performances

A new type of six-wing synchronous rotor has been designed and manufactured for mixing requirements of the short fiber-rubber composite material. During the manufacturing process of the composite material, different addition proportions of the short fibers have been used. The physical and mechanical performances of the short fiber-rubber composite material have been investigated. The new type rotor meets the mixing requirements of the short fiber-rubber composite material, with the best addition proportion of the short fibers.

scholarly journals PENGARUHORIENTASI DANFRAKSI VOLUME SERAT DAUN NANAS (ANANAS COMOSUS)TERHADAP KEKUATAN TARIK KOMPOSIT POLYESTERTAK JENUH(UP)

2012 ◽  
Vol 2 (1) ◽  
Author(s):  
Paryanto Dwi Setyawan ◽  
Nasmi Herlina Sari ◽  
Dewa Gede Pertama Putra
Keyword(s):  
Tensile Strength ◽  
Fiber Orientation ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Short Fiber ◽  
Ananas Comosus ◽  
Short Fibers ◽  
Random Orientation ◽  
Fiber Volume ◽  
Pineapple Leaves

Composite manufacturing is done by hand lay-up method with a fiber volume fraction 10%, 20%, 30%, and 40% with unidirectional and random short fiber orientation of pineapple leaves. Specimen testing is performed with a standard tensile strength test ASTM D3039. As a results is known that the tensile strength of composites increased with increasing fiber volume fraction for unidirectional fiber orientation, but rather to the random orientation of short fibers. Meanwhile, the composite tensile strain increases withincreasingfibervolume fractionfor both theorientation of thefibersof pineappleleaves.

Experimental Study of Screw Speed Effects on Quality of Short Fiber-Rubber Composite Material

2011 ◽  
Vol 221 ◽  
pp. 369-372 ◽  
Author(s):  
Chuan Sheng Wang ◽  
De Wei Zhang ◽  
Hui Guang Bian ◽  
Xiao Bo Wang ◽  
Lei Guo
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Composite Material ◽  
Physical And Mechanical Properties ◽  
Short Fiber ◽  
Experimental Results ◽  
Short Fibers ◽  
Screw Speed ◽  
Rubber Composite

During the extruding process of short fiber-rubber composite material, screw speed is an important factor which influences the orientation of short fibers, as well as the physical and mechanical properties of short fiber-rubber composite material. The effects of different screw speeds on physical and mechanical properties of short fiber-rubber composite material have been studied by experimental study. In the experiments, the screw speeds were 10rpm, 15rpm, 20rpm, 25rpm and 30rpm respectively. The experimental results indicated that when the screw speed was 15rpm, the physical and mechanical properties of short fiber-rubber composite material are better.

APPLICATION OF OIL PALM EMPTY FRUIT BUNCH FIBERS IN STRENGTH IMPROVEMENT AS A FIBER REINFORCED CONCRETE

2017 ◽  
Vol 25 (3) ◽  
pp. 161-170
Author(s):  
Henny Lydiasari ◽  
Ari Yusman Manalu ◽  
Rahmi Karolina
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Crack Length ◽  
Oil Palm ◽  
Fiber Reinforced Concrete ◽  
Structural Concrete ◽  
Empty Fruit Bunches ◽  
Construction Products ◽  
By Products ◽  
Strength Improvement

The potency of oil palm empty fruit bunches (OPEFB) fibers as one of the by-products of processing oil palm is increasing significantly so that proper management is needed in reducing environmental impact. One of the utilization of OPEFB fibers is as a substitution material in construction which usually the material is derived from non-renewable mining materials so that the number is increasingly limited. Therefore, it is necessary to study to know the performance of OPEFB fiber in making construction products especially concrete. In this case, the experiment was conducted using experimental method with variation of fiber addition by 0%, 10%, 15%, 20%, 25%, and 30%. Each specimen was tested by weight, slump value, compressive strength, tensile strength, elasticity and crack length. As the results, the variation of fibers addition by 10%, decrease of slump value is 7%, concrete weight is 3% and crack length is 8% while increase of the compressive strength is 2.7% and the modulus of elasticity is 33.3% but its tensile strength decreased insignificantly by 0.05% . Furthermore, the addition of fibers above 10% to 30% decreased compressive strength is still below 10% and tensile strength below 2% while the weight of concrete, slump value and crack length decreased. Therefore, the addition of 10% can replace the performance of concrete without fiber but the addition of above 10% can still be used on non-structural concrete.

The Mechanical Behavior of Short-Fiber-Elastomer Composites

1976 ◽  
Vol 49 (5) ◽  
pp. 1167-1181 ◽  
Author(s):  
A. Y. Coran ◽  
P. Hamed ◽  
L. A. Goettler
Keyword(s):  
Test Piece ◽  
Composite Plates ◽  
Short Fiber ◽  
Strength Properties ◽  
Unidirectional Composite ◽  
Short Fibers ◽  
Principal Stresses ◽  
Elastomer Composites ◽  
Ultimate Limit ◽  
Time Of Failure

Abstract The measured elastic and strength properties of angle-ply composites of short fibers and rubber depend on test-piece geometry. In general, higher tensile moduli and strengths are obtained when plies are both thin and wide. Once the effects of test-piece geometry are taken into account, elastic properties can be calculated as functions of the properties of a single ply. Classical compliance transformation equations can be used. However, because of the invariance of shear modulus in aligned composites, the tensor transformation equations are somewhat simplified. Tensile strengths of off-axis unidirectional composite plates and balanced-angle plies can be fitted by Hill's criterion. Unidirectional composites tend to fail in the weakest mode, depending on the angle of stress, but laminating causes all principal stresses in a ply to be near their ultimate limit at the time of failure.

Effect of Friction Stir Welding Parameters on Thermal and Tensile Behavior of Aluminum Weldments Using Double Shoulder Tools

2012 ◽  
Vol 622-623 ◽  
pp. 323-329
Author(s):  
Ebtisam F. Abdel-Gwad ◽  
A. Shahenda ◽  
S. Soher
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Tensile Behavior ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aluminum Base ◽  
Tool Pin ◽  
Strength And Ductility

Friction stir welding (FSW) process is a solid state welding process in which the material being welded does not melt or recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters and tool pin profile play major roles in deciding the weld quality. In this investigation, an attempt has been made to understand effects of process parameters include rotation speeds, welding speeds, and pin diameters on al.uminum weldment using double shoulder tools. Thermal and tensile behavior responses were examined. In this direction temperatures distribution across the friction stir aluminum weldment were measured, besides tensile strength and ductility were recorded and evaluated compared with both single shoulder and aluminum base metal.

scholarly journals The Influence of the Asymmetric Arb Process on the Properties of Al-Mg-Al Multi-Layer Sheets / Wpływ Asymetrii W Procesie Arb Na Właściwości Wielowarstwowych Blach Al-Mg-Al

2015 ◽  
Vol 60 (4) ◽  
pp. 2821-2826 ◽  
Author(s):  
A. Wierzba ◽  
S. Mróz ◽  
P. Szota ◽  
A. Stefanik ◽  
R. Mola
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Rolling Process ◽  
Asymmetry Factor ◽  
Relative Reduction ◽  
Test Results ◽  
Initial Thickness ◽  
Asymmetric Rolling ◽  
Aluminium Layer

The paper presents the results of the experimental study of the three-layer Al-Mg-Al sheets rolling process by the ARB method. The tests carried out were limited to single-pass symmetric and asymmetric rolling processes. An Al-Mg-Al package with an initial thickness of 4 mm (1-2-1 mm) was subjected to the process of rolling with a relative reduction of 50%. To activate the shear band in the strip being deformed, an asymmetry factor of av=2 was applied. From the test results, an increase in the tensile strength of the multi-layer Al-Mg-Al sheets obtained from the asymmetric process was observed. Microhardness tests did not show any significant differences in aluminium layer between respective layers of sheets obtained from the symmetric and the asymmetric process. By contrast, for the magnesium layer, an increase in microhardness from 72 HV to 79 HV could be observed for the asymmetric rolling. The analysis of the produced Al-Mg-Al sheets shows that the good bond between individual layers and grain refinement in the magnesium layer contributed to the obtaining of higher mechanical properties in the multi-layer sheets produced in the asymmetric process compared to the sheets obtained from the symmetric process.

Sign in / Sign up

Export Citation Format

Share Document