THE PRACTICAL VIEW IN GEOPHYSICAL EXPLORATION FOR METALLIC ORE BODIES

Geophysics ◽  
1948 ◽  
Vol 13 (4) ◽  
pp. 550-555
Author(s):  
L. C. Armstrong ◽  
D. M. Davidson
Keyword(s):  
Geophysical Methods ◽  
Ore Deposits ◽  
Depth Range ◽  
Geophysical Prospecting ◽  
Second Development ◽  
Mining Companies ◽  
Ore Bodies ◽  
Geophysical Surveys ◽  
Fundamental Research ◽  
Physical Effects

This is a nontechnical paper dealing with the potentialities of geophysical methods in the search for metallic ore bodies which do not outcrop. It emphasizes what exploration engineers are entitled to expect as well as to demand from geophysical surveys. Harmful misconceptions and frustrations have arisen among mining men through lack of understanding of the possibilities of the various methods, and through confusion traceable to the loose claims and looser interpretation of results on the part of some geophysical surveyors. The miner should be made to understand that geophysical methods merely measure physical effects, either inherent, or induced, in various rock bodies, and that high geological competence is usually needed to judge whether anomalous measurements may be correlative with ore, likely ore‐bearing structures or with features totally unrelated to ore occurrences. Since they do not put any tags on ore bodies, as some have been led to believe, the capabilities and limitations of the methods need further clarification. The biggest hurdles to overcome before geophysics can reach a fuller measure of its true potentialities in ore finding are, first, the development of techniques for mitigating or eliminating the anomalous effects of overburden; second, development of methods for detection of disseminated metallic sulphide deposits; third, perfection of techniques of investigating the rocks surrounding bore holes for appreciable distances; fourth, the improvement of techniques for geophysical prospecting underground; fifth, independent consultation before a survey is started to weigh dispassionately the chances for success (geophysical surveys should be checked with much pains and precision by repeating traverses and readings); sixth, reduction in costs for all methods; and seventh, modification and improvement in efficiency of equipment with special attention to increasing depth range. Finally, there is a critical need for research, long‐range, indirect, fundamental research, as well as direct research on known ore deposits which have not been disturbed too much by development or mining. This latter will be most profitably carried out if undertaken by private mining companies on their own properties and with complete cooperation from their own geological staffs.

The use of geophysical prospecting for imaging active faults in the Roer Graben, Belgium

Geophysics ◽  
2001 ◽  
Vol 66 (1) ◽  
pp. 78-89 ◽  
Author(s):  
Donat Demanet ◽  
François Renardy ◽  
Kris Vanneste ◽  
Denis Jongmans ◽  
Thierry Camelbeeck ◽  
...  
Keyword(s):  
High Resolution ◽  
Physical Properties ◽  
Fault Zone ◽  
Geophysical Methods ◽  
Depth Range ◽  
Electrical Tomography ◽  
Reflection Seismic ◽  
Refraction Seismic ◽  
Geophysical Surveys ◽  
Geophysical Techniques

As part of a paleoseismological investigation along the Bree fault scarp (western border of the Roer Graben), various geophysical methods [electrical profiling, electromagnetic (EM) profiling, refraction seismic tests, electrical tomography, ground‐penetrating radar (GPR), and high‐resolution reflection seismic profiles] were used to locate and image an active fault zone in a depth range between a few decimeters to a few tens of meters. These geophysical investigations, in parallel with geomorphological and geological analyses, helped in the decision to locate trench excavations exposing the fault surfaces. The results could then be checked with the observations in four trenches excavated across the scarp. Geophysical methods pointed out anomalies at all sites of the fault position. The contrast of physical properties (electrical resistivity and permittivity, seismic velocity) observed between the two fault blocks is a result of a differences in the lithology of the juxtaposed soil layers and of a change in the water table depth across the fault. Extremely fast techniques like electrical and EM profiling or seismic refraction profiles localized the fault position within an accuracy of a few meters. In a second step, more detailed methods (electrical tomography and GPR) more precisely imaged the fault zone and revealed some structures that were observed in the trenches. Finally, one high‐resolution reflection seismic profile imaged the displacement of the fault at depths as large as 120 m and filled the gap between classical seismic reflection profiles and the shallow geophysical techniques. Like all geophysical surveys, the quality of the data is strongly dependent on the geologic environment and on the contrast of the physical properties between the juxtaposed formations. The combined use of various geophysical techniques is thus recommended for fault mapping, particularly for a preliminary investigation when the geological context is poorly defined.

GEOPHYSICAL METHODS ADAPTED TO HIGHWAY ENGINEERING PROBLEMS

Geophysics ◽  
1952 ◽  
Vol 17 (3) ◽  
pp. 505-530 ◽  
Author(s):  
R. Woodward Moore
Keyword(s):  
Seismic Refraction ◽  
Geophysical Methods ◽  
Engineering Structures ◽  
Highway Engineering ◽  
Earth Resistivity ◽  
The Earth ◽  
Ore Bodies ◽  
Geophysical Surveys ◽  
Engineering Problems ◽  
Test Use

Of the several geophysical methods used in exploration for oil and useful ore bodies, the earth‐resistivity and seismic‐refraction tests have been found to be the most adaptable to the shallow tests generally required in highway construction work. Of these, the earth‐resistivity test is the faster and has a wider range of application to highway problems than does the seismic test. Use of both methods of tests in subsurface explorations for engineering structures is expanding. The paper cites a growing need for a more thorough subsurface investigation of all engineering structure sites and gives examples of field data obtained by the Bureau of Public Roads when making preliminary geophysical surveys of proposed highway locations or structure sites. The economic aspects and the advantages and limitations of the two methods of test are discussed with particular reference to their application to highway engineering problems.

scholarly journals SOME PROBLEMS OF ELECTRICAL GEOPHYSICAL PROSPECTING METHODS USED FOR EXPLORATION OF ORE DEPOSITS

2021 ◽  
Vol 12 (3S) ◽  
pp. 731-747
Author(s):  
V. A. Kulikov ◽  
A. G. Yakovlev ◽  
V. A. Polikarpova
Keyword(s):  
Mineral Exploration ◽  
Geophysical Methods ◽  
Mining Industry ◽  
Induced Polarization ◽  
Ore Deposits ◽  
Navigation Systems ◽  
Geophysical Prospecting ◽  
Electrical Prospecting ◽  
Satellite Navigation Systems ◽  
2D And 3D

Electrical geophysical prospecting methods are widely used at different stages of geological exploration. In the last two decades, new computer technologies and satellite navigation systems were successfully introduced in the geophysical industry. As a result, exploration technologies have improved, and new geophysical methods have been developed, such as electrical resistivity tomography (ERT) and spectral induced polarization (SIP) methods. An important role in ore geophysics is played by magnetotelluric (MT) methods. In this article, we focus on the issues of methodology and interpretation of electrical prospecting data for solving ore exploration problems. Special attention is paid to the induced polarization (IP) method that is most widely used in mineral exploration and mining industry as one of the most important and most dynamically developing techniques of ore geophysics. In addition, the issues of correct choices of survey scales and the use of automatic 2D and 3D inversion programs are considered.

Integration of Multi-geophysical Approaches to Identify Potential Pathways of Heavy Metals Contamination - A Case Study in Zeida, Morocco

2020 ◽  
Vol 25 (3) ◽  
pp. 415-423
Author(s):  
Ahmed Lachhab ◽  
El Mehdi Benyassine ◽  
Mohamed Rouai ◽  
Abdelilah Dekayir ◽  
Jean C. Parisot ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Seismic Velocity ◽  
Seismic Refraction ◽  
Geophysical Methods ◽  
Low Frequency ◽  
Electrical Current ◽  
P Wave ◽  
Low Resistivity ◽  
Refraction Tomography ◽  
Geophysical Surveys

The tailings of Zeida's abandoned mine are found near the city of Midelt, in the middle of the high Moulouya watershed between the Middle and the High Atlas of Morocco. The tailings occupy an area of about 100 ha and are stored either in large mining pit lakes with clay-marl substratum or directly on a heavily fractured granite bedrock. The high contents of lead and arsenic in these tailings have transformed them into sources of pollution that disperse by wind, runoff, and seepage to the aquifer through faults and fractures. In this work, the main goal is to identify the pathways of contaminated water with heavy metals and arsenic to the local aquifers, water ponds, and Moulouya River. For this reason, geophysical surveys including electrical resistivity tomography (ERT), seismic refraction tomography (SRT) and very low-frequency electromagnetic (VLF-EM) methods were carried out over the tailings, and directly on the substratum outside the tailings. The result obtained from combining these methods has shown that pollutants were funneled through fractures, faults, and subsurface paleochannels and contaminated the hydrological system connecting groundwater, ponds, and the river. The ERT profiles have successfully shown the location of fractures, some of which extend throughout the upper formation to depths reaching the granite. The ERT was not successful in identifying fractures directly beneath the tailings due to their low resistivity which inhibits electrical current from propagating deeper. The seismic refraction surveys have provided valuable details on the local geology, and clearly identified the thickness of the tailings and explicitly marked the boundary between the Triassic formation and the granite. It also aided in the identification of paleochannels. The tailings materials were easily identified by both their low resistivity and low P-wave velocity values. Also, both resistivity and seismic velocity values rapidly increased beneath the tailings due to the compaction of the material and lack of moisture and have proven to be effective in identifying the upper limit of the granite. Faults were found to lie along the bottom of paleochannels, which suggest that the locations of these channels were caused by these same faults. The VLF-EM surveys have shown tilt angle anomalies over fractured areas which were also evinced by low resistivity area in ERT profiles. Finally, this study showed that the three geophysical methods were complementary and in good agreement in revealing the pathways of contamination from the tailings to the local aquifer, nearby ponds and Moulouya River.

Application of geophysical methods for the investigation of the large gravitational mass movement of Séchilienne, France

2005 ◽  
Vol 42 (4) ◽  
pp. 1105-1115 ◽  
Author(s):  
O Meric ◽  
S Garambois ◽  
D Jongmans ◽  
M Wathelet ◽  
J L Chatelain ◽  
...  
Keyword(s):  
Rock Mass ◽  
Mass Movement ◽  
Seismic Refraction ◽  
Geophysical Methods ◽  
Time Lapse ◽  
Gravitational Mass ◽  
Electrical Tomography ◽  
Refraction Tomography ◽  
Geophysical Surveys ◽  
Geophysical Techniques

Several geophysical techniques (electromagnetic profiling, electrical tomography, seismic refraction tomography, and spontaneous potential and seismic noise measurement) were applied in the investigation of the large gravitational mass movement of Séchilienne. France. The aim of this study was to test the ability of these methods to characterize and delineate the rock mass affected by this complex movement in mica schists, whose lateral and vertical limits are still uncertain. A major observation of this study is that all the zones strongly deformed (previously and at present) by the movement are characterized by high electrical resistivity values (>3 kΩ·m), in contrast to the undisturbed mass, which exhibits resistivity values between a few hundred and 1 kΩ·m. As shown by the surface observations and the seismic results, this resistivity increase is due to a high degree of fracturing associated with the creation of air-filled voids inside the mass. Other geophysical techniques were tested along a horizontal transect through the movement, and an outstanding coherency appeared between the geophysical anomalies and the displacement rate curve. These preliminary results illustrate the benefits of combined geophysical techniques for characterizing the rock mass involved in the movement. Results also suggest that monitoring the evolution of the rock mass movement with time-lapse geophysical surveys could be beneficial.Key words: gravitational movement, geophysical methods, Séchilienne.

scholarly journals Verification of geophysical models in Alpine permafrost using borehole information

2000 ◽  
Vol 31 ◽  
pp. 300-306 ◽  
Author(s):  
Daniel S. Vonder Mühll ◽  
Christian Hauck ◽  
Frank Lehmann
Keyword(s):  
Geophysical Methods ◽  
Swiss Alps ◽  
Rock Glacier ◽  
Surface Microtopography ◽  
Refraction Seismics ◽  
Geophysical Surveys ◽  
Ground Conditions ◽  
Lateral Extent ◽  
Ice Content ◽  
Difficult Terrain

AbstractAt two permafrost sites in the Swiss Alps a range of geophysical methods were applied to model the structure of the subsurface. At both sites, borehole information was used to verify the quality of the model results. On the Murtèl-Corvatsch rock glacier (2700 m a.s.L; upper Engadine) a 58 m deep core drilling was performed in 1987. D. c resistivity measurements, refraction seismics, ground-penetrating radar (GPR) and gravimetric surveys allowed the shape of the permafrost table beneath the marked surface microtopography to be determined and the lateral extent of a deeper shear horizon to be established The validity of each method was verified by the borehole information (cores, density log and temperature). A coherent model of the rock-glacier structure was developed. At the Schilthorn (2970 m a.s.L; Bernese Oberland), it was not clear whether permafrost is in fact present. Various geophysical surveys (d.c. resistivity tomography, refraction seismics, GPR and EM-31) gave results that were not typical of permafrost environments. A 14 m percussion drilling revealed warm permafrost and a very low ice content. These geotechnical and geothermal data allowed reinterpretation of the geophysical results, improving modelling of ground conditions. The paper demonstrates that in the difficult terrain of Alpine permafrost, boreholes may be critical in calibration and verification of the results of geophysical methods. The most useful combinations of geophysical techniques proved to be (a) seismics with d.c. resistivity, and (b) gravimetry with GPR.

Investigating the Effective Resistivity of Reinforced Concrete Waste Storage Tanks at the Hanford Site

Geophysics ◽  
2021 ◽  
pp. 1-50
Author(s):  
Allan Haas ◽  
Dale F. Rucker ◽  
Marc T. Levitt
Keyword(s):  
Electrical Resistivity ◽  
Reinforced Concrete ◽  
Geophysical Methods ◽  
Underground Storage ◽  
Storage Tanks ◽  
Hanford Site ◽  
Underground Storage Tanks ◽  
Effective Resistivity ◽  
Geophysical Surveys ◽  
Wide Range

Industrialized sites pose challenges for conducting electrical resistivity geophysical surveys, as the sites typically contain metallic infrastructure that can mask electrolytic-based soil and groundwater contamination. The Hanford site in eastern Washington State, USA, is an industrialized site with underground storage tanks, piping networks, steel fencing, and other potentially interfering infrastructure that could inhibit the effectiveness of electrical resistivity tomography (ERT) to map historical and monitor current waste releases. The underground storage tanks are the largest contributor by volume to subsurface infrastructure and can be classified as reinforced concrete structures with an internal steel liner. Directly measuring the effective value for the electrical resistivity of the tank, i.e., the combination of individual components that comprise the tank’s shell, is not reasonably possible because they are buried and dangerously radioactive. Therefore, we indirectly assess the general resistivity of the tanks and surrounding infrastructure by developing synthetic ERT models with a parametric forward modeling study using a wide range of resistivity values from 1×10−6 to 1×104 ohm-m, which are equivalent to steel and dry rock, respectively. The synthetic models used the long-electrode ERT method (LE-ERT), whereby steel cased metallic wells surrounding the tanks are used as electrodes. The patterns and values of the synthetic tomographic models were then compared to LE-ERT field data from the AX tank farm at the Hanford site. This indirect method of assessing the effective resistivity revealed that the reinforced concrete tanks are electrically resistive and the accompanying piping infrastructure has little influence on the overall resistivity distribution when using electrically based geophysical methods for characterizing or monitoring waste releases. Our findings are consistent with nondestructive testing literature that also shows reinforced concrete to be generally resistive.

Tectonic state and oil-gas prospects of Khidirly-Bandovan structure according to the new gravimetric data

2020 ◽  
pp. 11-18
Author(s):  
A.S. Hasanov ◽  
◽  
◽  
Keyword(s):  
Geophysical Methods ◽  
Geological Mapping ◽  
Seismic Exploration ◽  
Huge Amount ◽  
Ray Method ◽  
Common Depth Point ◽  
Geophysical Surveys ◽  
Gravimetric Data ◽  
Exploration Drilling ◽  
Oil Gas

Khidirly-Bandovan structures have been studied through geological mapping, structural exploration drilling, geophysical methods (gravimetric, magnetic, electrical, seismic exploration methods) since the 1930s. Small amount of oil from different wells in the upper part of Productive Series (PS) and huge amount of gas fountain from Middle Absheron sediments have been obtained. As the interest to these areas had not decreased, the geophysical surveys continued during further years. Seismic exploration surveys were executed in Bandovan structure via Common Depth Point (CDP) method in 2004, refracted ray method and gravimetric exploration complex in 2006 and 3D seismic exploration works and gravimetric investigations with “Scintrex CG-5 Autograv” devices in 2016, correspondingly. In the result of analysis of distribution characteristics for local gravimetric anomalies, as well as 3D descriptions of new gravimetric data, up-to-date logs on tectonic state of Khidirly-Bandovan structure have been obtained and as the new oil-gas exploration objects, the west and south-west wings of these structures highlighted.

scholarly journals Geophysical identification of voids and loosened zones in the shallow subsurface of post-mining areas

2018 ◽  
Vol 66 ◽  
pp. 01001 ◽  
Author(s):  
Zenon Pilecki
Keyword(s):  
Rock Mass ◽  
Geophysical Methods ◽  
Ore Deposits ◽  
Hard Coal ◽  
Shallow Subsurface ◽  
Mining Areas ◽  
Upper Silesian Coal Basin ◽  
Discontinuous Deformation ◽  
Ground Penetrating ◽  
Terrain Surface

The shallow historic exploitation of Zn-Pb/Fe ore deposits as well as hard coal has generated many discontinuous deformations on the terrain surface in the Upper Silesian Coal Basin/Poland. Discontinuous deformations occur in different forms as sinkholes, synclines, cracks, faults or ditches. The basic cause of their occurrence is the presence of void and loosened zones in the shallow subsurface. If the appropriate conditions arise, the sinkhole process begins to move upwards and may cause a discontinuous deformation on the terrain surface. Typically, geophysical methods are used for void and loosened zone identification. The most effective methods are gravimetric, seismic, electric resistivity and ground penetrating radar (GPR). Geophysical testing, requires distinct changes in the physical properties in the rock mass. The identified geophysical anomalies should be verified by control borehole and borehole tests to confirm the presence of the void and loosened zones in the rock mass. The results of control drilling and borehole tests determine the need to apply treatment works. In order to assess the threat of the occurrence of discontinuous deformations in the areas of historical shallow mining in Upper Silesia, a classification system based on geophysical tests has also been developed.

scholarly journals Seismic Methods in Geothermal Water Resource Exploration: Case Study from Łódź Trough, Central Part of Poland

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Tomasz Maćkowski ◽  
Anna Sowiżdżał ◽  
Anna Wachowicz-Pyzik
Keyword(s):  
Estimation Error ◽  
Geophysical Methods ◽  
Petroleum Industry ◽  
Geological Structure ◽  
Seismic Survey ◽  
Energy Potential ◽  
Geothermal Resources ◽  
Geothermal Waters ◽  
Seismic Methods ◽  
Geophysical Surveys

The geothermal waters constitute a specific type of water resources, very important from the point of view of their thermal energy potential. This potential, when utilized, supplies an ecological and renewable energy, which, after effective development, brings many environmental, social, and industrial benefits. The key element of any geothermal investment is the proper location of geothermal installation, which would guarantee the relevant hydrogeothermal parameters of the water intake. Hence, many studies and analyses are carried out in order to characterize the reservoir parameters, including the integrated geophysical methods. For decades, the geophysical surveys have been the trusty recognition methods of geological structure and petrophysical parameters of rock formations. Thus, they are widely applied by petroleum industry in exploration of conventional and unconventional (shale gas/oil, tight gas) hydrocarbon deposits. Advances in geophysical methods extended their applicability to many other scientific and industrial branches as, e.g., the seismic survey used in studies of geothermal aquifers. The following paper presents the opportunities provided by seismic methods applied to studies of geothermal resources in the central Poland where the geothermal waters are reservoired in both the Lower Cretaceous and the Lower Jurassic sedimentary successions. The presented results are obtained from a network of seismic profiles. An important advantage of the seismic survey is that they may support the selection of an optimal location of geothermal investment and determination of the geometry of geothermal aquifer. Furthermore, the application of geophysical methods can significantly contribute to the reduction of estimation error of groundwater reservoir temperature.

Sign in / Sign up

Export Citation Format

Share Document