Energy balance of a drill-bit seismic source, part 1: Rotary energy and radiation properties

Geophysics ◽  
2005 ◽  
Vol 70 (2) ◽  
pp. T13-T28 ◽  
Author(s):  
Flavio Poletto
Keyword(s):  
Near Field ◽  
Seismic Source ◽  
Drill String ◽  
Drill Bit ◽  
Vertical Force ◽  
Rotary Drilling ◽  
Operational Conditions ◽  
Radiation Properties ◽  
Unbounded Media ◽  
The Waves

An issue in seismic-while-drilling (SWD) technology is to characterize the dynamic and radiation properties of the drill-bit source working under different operational conditions. The energy requirements, power losses, local crack effects, radiation, and near-field effects associated with rotary drilling are analyzed to quantify the waves produced by an SWD vertical force acting in bounded and unbounded media. Results are expressed in terms of a complex integrated impedance and the equations for rotary drilling. The calculations — extended to the waves in the drill string — are used in part 2 of this paper (Poletto, 2005, this issue) to quantify the performance of actual drill-bit sources.

Seismic-while-drilling drill-bit source by ground force: Concept and application

Geophysics ◽  
2020 ◽  
Vol 85 (3) ◽  
pp. MR167-MR178
Author(s):  
Flavio Poletto ◽  
Francesco Miranda ◽  
Biancamaria Farina ◽  
Andrea Schleifer
Keyword(s):  
Signal To Noise Ratio ◽  
Near Field ◽  
Complex Impedance ◽  
Seismic Source ◽  
Drill Bit ◽  
Pilot Signal ◽  
Effective Removal ◽  
Source Signal ◽  
Diffusion Phase ◽  
Drilling Conditions

For four decades, the use of the drill-bit seismic source has been evaluated extensively and investigated for seismic-while-drilling (SWD) purposes. After an initial diffusion phase, however, the routine application on drill-bit reverse vertical seismic profiling (RVSP) has declined because of issues related to variability in the signal-to-noise ratio of drill-bit signals obtained with different drilling conditions. Consequently, additional efforts have been dedicated to improving the recording of reference signals. Recent technology developments enable direct ground-force pilot measurements at downhole positions close to the bit, which enable reliable estimations of the far-field drill-bit-radiated signature. The knowledge of the ground force below the source in the near-field is a key aspect not only for the exploitation of the drill-bit source but also for conventional seismic vibrator sources. The SWD deconvolved results obtained by the ground force are different from those obtained by recording only motion vibration, such as acceleration. The ground force and particle velocity are linked by a complex impedance in the near-field, and together they provide dual measurements. In addition, the ground force provides signals with effective coupling conditions at the bit-rock interface in the presence of the drill-bit displacement action with penetration during rock fracturation. The analysis of the impedance at the bit source includes the drillstring reflections, which are observed in the reference drillstring pilot signal and are simulated by using an appropriate mechanical model. The processing of real seismic signals with different approaches by deconvolution and correlation using ground-force and motion signals produces improvements in the extraction of the source signal, with effective removal of the undesired pilot wavefields, and with cleaner estimations of the drill-bit seismic wavefields in a crosswell survey.

Energy balance of a drill-bit seismic source, part 2: Drill-bit versus conventional seismic sources

Geophysics ◽  
2005 ◽  
Vol 70 (2) ◽  
pp. T29-T44 ◽  
Author(s):  
Flavio Poletto
Keyword(s):  
Polycrystalline Diamond ◽  
Seismic Source ◽  
Drill Bit ◽  
Stick Slip ◽  
Radiation Properties ◽  
Bit Wear ◽  
Pressure Modulation ◽  
Cutter Forces ◽  
Mud Pressure ◽  
Drilling Conditions

The radiation properties of a downhole drill-bit seismic source are related to the amplitude and frequency of the forces exerted by the working bit. The main vibration modes of roller-cone and polycrystalline diamond compact (PDC) bits are investigated under different drilling conditions. The analysis includes vibrations produced by teeth indention, multilobed patterns, bouncing with periodic and random effects, single-cutter forces, stick-slip and whirling effects, mud-pressure modulation forces, and bit wear. Drill-bit radiation properties are calculated using the results obtained in part 1 of this paper and are numerically compared to the radiation of conventional vertical seismic profiling (VSP) sources.

scholarly journals Effects of gap thickness and emitter location on the photoluminescence enhancement of monolayer MoS2 in a plasmonic nanoparticle-film coupled system

Nanophotonics ◽  
2020 ◽  
Vol 9 (7) ◽  
pp. 2097-2105
Author(s):  
Xiaozhuo Qi ◽  
Tsz Wing Lo ◽  
Di Liu ◽  
Lantian Feng ◽  
Yang Chen ◽  
...  
Keyword(s):  
Near Field ◽  
Central Area ◽  
Field Enhancement ◽  
Coupled System ◽  
Film Structure ◽  
Plasmonic Nanoparticle ◽  
Emitter Location ◽  
Radiation Properties ◽  
Radiation Enhancement ◽  
Quantum Emitters

AbstractPlasmonic nanocavities comprised of metal film-coupled nanoparticles have emerged as a versatile nanophotonic platform benefiting from their ultrasmall mode volume and large Purcell factors. In the weak-coupling regime, the particle-film gap thickness affects the photoluminescence (PL) of quantum emitters sandwiched therein. Here, we investigated the Purcell effect-enhanced PL of monolayer MoS2 inserted in the gap of a gold nanoparticle (AuNP)–alumina (Al2O3)–gold film (Au Film) structure. Under confocal illumination by a 532 nm CW laser, we observed a 7-fold PL peak intensity enhancement for the cavity-sandwiched MoS2 at an optimal Al2O3 thickness of 5 nm, corresponding to a local PL enhancement of ∼350 by normalizing the actual illumination area to the cavity’s effective near-field enhancement area. Full-wave simulations reveal a counterintuitive fact that radiation enhancement comes from the non-central area of the cavity rather than the cavity center. By scanning an electric dipole across the nanocavity, we obtained an average radiation enhancement factor of about 65 for an Al2O3 spacer thickness of 4 nm, agreeing well with the experimental thickness and indicating further PL enhancement optimization. Our results indicate the importance of configuration optimization, emitter location and excitation condition when using such plasmonic nanocavities to modulate the radiation properties of quantum emitters.

Study of stick–slip suppression and robustness to parametric uncertainty in drill strings containing torsional vibration tool using sliding-mode control

2021 ◽  
pp. 146441932110452
Author(s):  
Jialin Tian ◽  
Jie Wang ◽  
Siqi Zhou ◽  
Yinglin Yang ◽  
Liming Dai
Keyword(s):  
Torsional Vibration ◽  
Complex Dynamics ◽  
Sliding Mode ◽  
Parametric Uncertainty ◽  
Drill String ◽  
Lumped Parameter Model ◽  
Drilling Process ◽  
Drill Bit ◽  
Stick Slip ◽  
Drilling Operations

Excessive stick–slip vibration of drill strings can cause inefficiency and unsafety of drilling operations. To suppress the stick–slip vibration that occurred during the downhole drilling process, a drill string torsional vibration system considering the torsional vibration tool has been proposed on the basis of the 4-degree of freedom lumped-parameter model. In the design of the model, the tool is approximated by a simple torsional pendulum that brings impact torque to the drill bit. Furthermore, two sliding mode controllers, U1 and U2, are used to suppress stick–slip vibrations while enabling the drill bit to track the desired angular velocity. Aiming at parameter uncertainty and system instability in the drilling operations, a parameter adaptation law is added to the sliding mode controller U2. Finally, the suppression effects of stick–slip and robustness of parametric uncertainty about the two proposed controllers are demonstrated and compared by simulation and field test results. This paper provides a reference for the suppression of stick–slip vibration and the further study of the complex dynamics of the drill string.

Exact seismograms for a point force using generalized ray theory

Geophysics ◽  
1983 ◽  
Vol 48 (11) ◽  
pp. 1421-1427 ◽  
Author(s):  
E. R. Kanasewich ◽  
P. G. Kelamis ◽  
F. Abramovici
Keyword(s):  
Half Space ◽  
Near Field ◽  
Sedimentary Basins ◽  
Transverse Component ◽  
Point Force ◽  
Seismic Exploration ◽  
Head Wave ◽  
Vertical Force ◽  
Low Velocity ◽  
Head Waves

Exact synthetic seismograms are obtained for a simple layered elastic half‐space due to a buried point force and a point torque. Two models, similar to those encountered in seismic exploration of sedimentary basins, are examined in detail. The seismograms are complete to any specified time and make use of a Cagniard‐Pekeris method and a decomposition into generalized rays. The weathered layer is modeled as a thin low‐velocity layer over a half‐space. For a horizontal force in an arbitrary direction, the transverse component, in the near‐field, shows detectable first arrivals traveling with a compressional wave velocity. The radial and vertical components, at all distances, show a surface head wave (sP*) which is not generated when the source is compressive. A buried vertical force produces the same surface head wave prominently on the radial component. An example is given for a simple “Alberta” model as an aid to the interpretation of wide angle seismic reflections and head waves.

The First Multilateral Well in Eastern Siberia on the Separated Oil Reservoirs

2021 ◽  
Author(s):  
Ruslan Fanisovich Gataullin ◽  
Stanislav Evgen’evich Ter-Saakov ◽  
Evgenij Vladimirovich Nikulin ◽  
Dmitriy Pavlovich Stifeev ◽  
Alexey Vyacheslavovich Filatov
Keyword(s):  
Low Frequency ◽  
Cost Effective ◽  
Drill String ◽  
Hole Drilling ◽  
Drill Bit ◽  
Eastern Siberia ◽  
Water Contact ◽  
Bottom Hole ◽  
Drilling Technology ◽  
Equipment Failures

Abstract This article describes engineering and technology solutions developed to successfully construct unconventional and unique horizontal well at the field of Eastern Siberia targeted to two isolated formations with an option to shut-off top Botuobinsky horizon after gas breakthrough and produce oil from underlying Ulakhansky bed further on. As oil-water contact in the lower part of Ulakhansky horizon makes fracturing the well inexpedient, multi hole drilling technology was implemented enabling drainage of the reserves that are far from the main borehole. The main objective of this well is to deplete Botuobinsky horizon subsequently shutting it off and continuing to recover petroleum reserves from Ulakhansky pay zone. Constructing such well is cost-effective, as it requires drilling only one intermediate casing interval instead of two. Accumulated experience of drilling and completing multi hole wells was used to ensure successful well construction; also, geological and stratigraphic data as well as possible complications while drilling Botuobunsky and Ulakhansky formations were analyzed in-depth. The following appliances were selected to meet the objective: –Bottom-hole equipment enabling drilling abrasive formations under conditions of high vibrations;–Special line of drill bits to ensure high ROP and successful sidetracking without additional tripping;–RSS with 152.4 mm drill bit. The goal set by the operating company was achieved through multi-faceted approach to performing the task, efficient cooperation of engineering technical services and continuous monitoring of output data while drilling. All that combined delivered the results listed below: –Sidetracks were carried out in an open horizontal hole without cement plugs and additional tripping for drill bit or BHA.–Minimized bottom-hole equipment failures under condition of increased high-frequency vibrations from bit while drilling hard formations due to implementation of modular PDM with data-transmitting channel.–Minimized bottom-hole equipment failures under condition of increased low-frequency vibrations from drill string with Hard Bending due to improved BHA design and optimized drilling parameters selection.–Liner was effectively run to Botuobinsky and Ulakhansky reservoirs with an option to shut-off the former after depletion and gas breakthrough. This well is the first one targeted at two isolated formations in East Siberia.

Far-field tsunami data assimilation for the 2015 Illapel earthquake

2019 ◽  
Vol 219 (1) ◽  
pp. 514-521 ◽  
Author(s):  
Y Wang ◽  
K Satake ◽  
R Cienfuegos ◽  
M Quiroz ◽  
P Navarrete
Keyword(s):  
Data Assimilation ◽  
Near Field ◽  
Source Parameters ◽  
Deep Ocean ◽  
Seismic Source ◽  
Far Field ◽  
Complementary Method ◽  
East Pacific ◽  
2015 Illapel Earthquake ◽  
Illapel Earthquake

SUMMARY The 2015 Illapel earthquake (Mw 8.3) occurred off central Chile on September 16, and generated a tsunami that propagated across the Pacific Ocean. The tsunami was recorded on tide gauges and Deep-ocean Assessment and Reporting of Tsunami (DART) tsunameters in east Pacific. Near-field and far-field tsunami forecasts were issued based on the estimation of seismic source parameters. In this study, we retroactively evaluate the potentiality of forecasting this tsunami in the far field based solely on tsunami data assimilation from DART tsunameters. Since there are limited number of DART buoys, virtual stations are assumed by interpolation to construct a more complete tsunami wavefront for data assimilation. The comparison between forecasted and observed tsunami waveforms suggests that our method accurately forecasts the tsunami amplitudes and arrival time in the east Pacific. This approach could be a complementary method of current tsunami warning systems based on seismic observations.

scholarly journals Measurement of bit-rock interface temperature and wear rate of the tungsten carbide drill bit during rotary drilling

Friction ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 1073-1082 ◽  
Author(s):  
Vijay Kumar Shankar ◽  
Bijay Mihir Kunar ◽  
Chivukula Suryanarayana Murthy ◽  
M. R. Ramesh
Keyword(s):  
Wear Rate ◽  
Tungsten Carbide ◽  
Interface Temperature ◽  
Drill Bit ◽  
Rotary Drilling ◽  
Rock Interface

Torsional Vibrations and Nonlinear Dynamic Characteristics of Drill Strings and Stick-Slip Reduction Mechanism

2019 ◽  
Vol 14 (8) ◽  
Author(s):  
Jialin Tian ◽  
Genyin Li ◽  
Liming Dai ◽  
Lin Yang ◽  
Hongzhi He ◽  
...  
Keyword(s):  
Torsional Vibration ◽  
Nonlinear Dynamic ◽  
Drill String ◽  
Drilling Process ◽  
Drill Bit ◽  
Torsional Vibrations ◽  
Reduction Mechanism ◽  
Nonlinear Dynamic Model ◽  
Stick Slip ◽  
Research Results

Torsional stick–slip vibrations easily occur when the drill bit encounters a hard or a hard-soft staggered formation during drilling process. Moreover, serious stick–slip vibrations of the drill string is the main factor leading to low drilling efficiency or even causing the downhole tools failure. Therefore, establishing the stick–slip theoretical model, which is more consistent with the actual field conditions, is the key point for new drilling technology. Based on this, a new torsional vibration tool is proposed in this paper, then the multidegree-of-freedom torsional vibrations model and nonlinear dynamic model of the drill string are established. Combined with the actual working conditions in the drilling process, the stick–slip reduction mechanism of the drill string is studied. The research results show that the higher rotational speed of the top drive, smaller viscous damping of the drill bit, and smaller WOB (weight on bit) will prevent the stick–slip vibration to happen. Moreover, the new torsional vibration tool has excellent stick–slip reduction effect. The research results and the model established in this paper can provide important references for reducing the stick–slip vibrations of the drill string and improving the rock-breaking efficiency.

Sign in / Sign up

Export Citation Format

Share Document