Efficiency Improvement Options for Municipal Waste-Fired Power Generation—Recent Development Activities in Japan: A Review

1995 ◽  
Vol 209 (2) ◽  
pp. 81-100 ◽  
Author(s):  
H Haneda
Keyword(s):  
Power Plants ◽  
High Efficiency ◽  
Primary Energy ◽  
Environmental Conservation ◽  
Municipal Waste ◽  
Current Status ◽  
Efficiency Improvement ◽  
Effective Utilization ◽  
Global Environmental ◽  
Technical Issues

The development of high-efficiency municipal waste-fired power plants, although not yet developed for practical use because of the technical difficulties involved, has recently come to be considered quite important, reflecting strong public demand for conservation of the global environment and preservation of energy resources. Development of such plants is now being actively promoted in various national projects in Japan. This paper first reviews the current status and technical issues concerning (a) municipal waste disposal plants and (b) municipal waste-fired power plants in Japan. Then each of the three approaches that are currently being proposed and vigorously promoted as national projects in Japan for realizing high-efficiency municipal waste-fired power plants is discussed. Although a high percentage of the municipal waste in Japan is incinerated, only a relatively small amount of electricity is generated at present. The paper shows that increasing the proportion of waste used to provide electricity could lead to savings of up to 30 per cent of the annual cost consumption in Japan, with accompanying substantial saving in CO2 emissions. The more effective utilization of municipal waste as an energy source would thus have a significant effect on global environmental conservation and in saving primary energy sources.

scholarly journals Combined Cycles Permit the Most Environmentally Benign Conversion of Fossil Fuels to Electricity

1990 ◽  
Author(s):  
Guenther Haupt ◽  
John S. Joyce ◽  
Konrad Kuenstle
Keyword(s):  
Environmental Impact ◽  
Power Plants ◽  
Fossil Fuels ◽  
Coal Gasification ◽  
High Efficiency ◽  
Waste Heat ◽  
Primary Energy ◽  
Combined Cycle ◽  
Point Of View ◽  
Steam Boiler

The environmental impact of unfired combined-cycle blocks of the GUD® type is compared with that of equivalent reheat steam boiler/turbine units. The outstandingly high efficiency of GUD blocks not only conserves primary-energy resources, but also commensurately reduces undesirable emissions and unavoidable heat rejection to the surroundings. In addition to conventional gas or oil-fired GUD blocks, integrated coal-gasification combined-cycle (ICG-GUD) blocks are investigated from an ecological point of view so as to cover the whole range of available fossil fuels. For each fuel and corresponding type of GUD power plant the most appropriate conventional steam-generating unit of most modern design is selected for comparison purposes. In each case the relative environmental impact is stated in the form of quantified emissions, effluents and waste heat, as well as of useful byproducts and disposable solid wastes. GUD blocks possess the advantage that they allow primary measures to be taken to minimize the production of NOx and SOx, whereas both have to be removed from the flue gases of conventional steam stations by less effective and desirable, albeit more expensive secondary techniques, e.g. flue-gas desulfurization and DENOX systems. In particular, the comparison of CO2 release reveals a significantly lower contribution by GUD blocks to the greenhouse effect than by other fossil-fired power plants.

Improvement in Recuperative Gas Cycles by Means of a Heat Generator Partly By-Passing the Recuperator: Application to Open and Closed Cycles and to Various Kinds of Energy

1979 ◽  
Author(s):  
Z. P. Tilliette ◽  
B. Pierre
Keyword(s):  
Power Plants ◽  
High Efficiency ◽  
Primary Energy ◽  
Operating Conditions ◽  
Heat Output ◽  
Medium Temperature ◽  
Heat Generator ◽  
High Temperature Process ◽  
Temperature Heat ◽  
Operation Flexibility

A particular arrangement applicable to open or closed recuperative gas cycles, consisting of a heat generator partly by-passing the low pressure side of the recuperator, is proven to enhance the advantages of gas cycles for energy production. In this way, the cogeneration of both power with high efficiency owing to the recuperator and high temperature process heat becomes possible and economically attractive. Furthermore, additional possibilities appear for power generation by combined gas and steam or ammonia cycles. In any case, the overall utilitization coefficient of the primary energy is increased and the combined production of low or medium temperature heat can also be improved. The great operation flexibility of the system for combined energy generation is worth being emphasized: the by-pass arrangement involves no significant change in the operating conditions of the main turbocompressor as the heat output varies. Applications of this arrangement are made to open and closed gas cycle power plants using fossil, nuclear and solar energies. The overall heat conversion efficiency is tentatively estimated in order to appreciate the energy conversion capability of the investigated power plants.

Comprehensive technical review of the high-efficiency low-emission technology in advanced coal-fired power plants

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Soonho Lee ◽  
Jongho Kim ◽  
Arash Tahmasebi ◽  
Chung-Hwan Jeon ◽  
Yangxian Liu ◽  
...  
Keyword(s):  
High Performance ◽  
Power Plants ◽  
High Efficiency ◽  
Emission Control ◽  
Current Status ◽  
Material Research ◽  
Technology Deployment ◽  
Low Emission ◽  
Technical Challenges ◽  
Control Technologies

Abstract Advancements in supercritical (SC), ultrasupercritical (USC), and advanced USC coal-fired power plants have been achieved through the development of enhanced materials utilized in advanced steam cycles and through the deployment of advanced emission control systems. These are referred to as high-efficiency low-emission (HELE) technologies, which may solve numerous issues associated with coal-based power generation. There is a clear global transition from subcritical to advanced power plant types and significant R&D work on HELE technologies. Therefore, this comprehensive review covers the latest HELE technology deployment in major coal-consuming countries and their R&D roadmaps to advance HELE technologies. In spite of the various advantages of HELE technologies, there have been numerous technical challenges relevant to achieving the HELE steam conditions and deploying low emission control technologies in the HELE systems. Hence, this review covers the technical challenges and the relevant recent research by using various coal combustion test facilities. The current focus for the progression from USC boilers to advanced USC boilers is a successful demonstration of the developed high-performance alloys under the advanced steam conditions. This review covers the current status of research and development of advanced USC (A-USC) materials and challenges based on the major material research programs.

Recent Advances in Heterostructured Photocatalysts for Degradation of Organic Pollutants.

2020 ◽  
Vol 17 ◽  
Author(s):  
Chen-Jing Sun ◽  
Li-Ping Zhao ◽  
Rui Wang
Keyword(s):  
Organic Pollutants ◽  
High Efficiency ◽  
Separation Efficiency ◽  
Organic Pollution ◽  
Utilization Rate ◽  
Type I ◽  
Human Beings ◽  
Global Challenge ◽  
Global Environmental ◽  
High Efficient

: With the development of industrialization, the global environmental pollution and energy crisis are becoming increasingly serious. Organic pollutants pose a serious health threat to human beings and other organisms. The removal of organic pollutants in environment has become a global challenge. The photocatalytic technology has been widely used in the degradation of organic pollutants with its characteristics of simple process, high efficiency, thorough degradation and no secondary pollution. However, the single photocatalyst represented by TiO2 has disadvantages of low light utilization rate and high recombination rate of photocarriers. Building heterojunction is considered one of the most effective methods to enhance the photocatalytic performance of single photocatalyst, which can improve the separation efficiency of photocarriers and utilization of visible light. The classical heterojunction can be divided into four different cases: type I, typeⅡ, p–n heterojunctions and Z-scheme junction. In this paper, the recent progress in the treatment of organic pollution by heterostructure photocatalysts is summarized and the mechanism of heterostructure photocatalysts for the treatment of organic pollutants is reviewed. It is expected that this paper can deepen the understanding of heterostructure photocatalysts and provide guidance for high efficient photocatalytic degradation of organic pollutants in the future.

"Recent Patents on the Triboelectrostatic Separation of Fly Ash"

2019 ◽  
Vol 13 ◽  
Author(s):  
Haisheng Li ◽  
Wenping Wang ◽  
Yinghua Chen ◽  
Xinxi Zhang ◽  
Chaoyong Li
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
High Efficiency ◽  
Separation Efficiency ◽  
High Reliability ◽  
Operating Conditions ◽  
Security Requirements ◽  
Unburned Carbon ◽  
Efficient Operation ◽  
Triboelectrostatic Separation

Background: The fly ash produced by coal-fired power plants is an industrial waste. The environmental pollution problems caused by fly ash have been widely of public environmental concern. As a waste of recoverable resources, it can be used in the field of building materials, agricultural fertilizers, environmental materials, new materials, etc. Unburned carbon content in fly ash has an influence on the performance of resource reuse products. Therefore, it is the key to remove unburned carbon from fly ash. As a physical method, triboelectrostatic separation technology has been widely used because of obvious advantages, such as high-efficiency, simple process, high reliability, without water resources consumption and secondary pollution. Objective: The related patents of fly ash triboelectrostatic separation had been reviewed. The structural characteristics and working principle of these patents are analyzed in detail. The results can provide some meaningful references for the improvement of separation efficiency and optimal design. Methods: Based on the comparative analysis for the latest patents related to fly ash triboelectrostatic separation, the future development is presented. Results: The patents focused on the charging efficiency and separation efficiency. Studies show that remarkable improvements have been achieved for the fly ash triboelectrostatic separation. Some patents have been used in industrial production. Conclusion: According to the current technology status, the researches related to process optimization and anti-interference ability will be beneficial to overcome the influence of operating conditions and complex environment, and meet system security requirements. The intelligent control can not only ensure the process continuity and stability, but also realize the efficient operation and management automatically. Meanwhile, the researchers should pay more attention to the resource utilization of fly ash processed by triboelectrostatic separation.

The Global Environmental Agenda of 2021 and the tasks of sustainable energy-ecological development and cooperation between Japan and countries Southeast Asia

2021 ◽  
pp. 951-965
Author(s):  
Yana Vadimovna Mishchenko
Keyword(s):  
Southeast Asia ◽  
Power Plants ◽  
Thermal Power ◽  
Energy Transition ◽  
Southeast Asian ◽  
Asia Pacific ◽  
Asian Countries ◽  
Global Environmental ◽  
The World ◽  
Southeast Asian Countries

The article discusses the main results of two major international summits held in October-November 2021, the key topics of which were the issues of the global fight against climate change and environmental protection. The decisions taken at these conferences, with the broad participation of world leaders, reflect the fundamental trends of the global environmental agenda. Within the framework of this agenda, Japan and the countries of Southeast Asia are building their modern energy and environmental cooperation. In this context, the article examines the main urgent tasks of energy-environmental interaction and sustainable development of Japan and the states of Southeast Asia. These countries are located in the Asia-Pacific region, which remains until now the main emitter of greenhouse gases in the world. However, the indicators of environmental pollution by Japan and the Southeast Asian countries are relatively not so high, compared to some other states in the region and the world. The article discusses the most relevant and significant examples of bilateral and multilateral cooperation between these countries in areas related to curbing global warming and climate protection. It has been revealed that with all the efforts made, since the 1990s, the indicators of reducing harmful emissions into the atmosphere in Japan remain modest and even lag behind some of the Western countries. The Southeast Asian countries show a serious attitude to the development of renewable energy, but their intention to abandon coal still raises some doubts about the methods of implementing this ambitious plan. In particular, it is currently not entirely clear whether these countries are preparing to make a full-fledged "energy transition" in the coming decades, or whether they just intend to replace their coal-fired thermal power plants with gas ones.

FEATURES OF THE METHODOLOGY OF THERMODYNAMIC MODELING OF GAS TURBINE AND COMBINED ON THEIR BASIS POWER PLANTS

2017 ◽  
Author(s):  
Gennadii Liubchik ◽  
◽  
Nataliia Fialko ◽  
Aboubakr Regragui ◽  
Julii Sherenkovskii ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Thermodynamic Analysis ◽  
Thermodynamic Modeling ◽  
Power Plants ◽  
High Efficiency ◽  
Technical Facility

The article presents the enthalpy-entropy methodology of thermodynamic analysis of gas turbine and combined power plants on their basis, the results of testing the method on a real technical facility, proving its high efficiency.

scholarly journals Advances in Corrosion-Resistant Thermal Spray Coatings for Renewable Energy Power Plants: Part II—Effect of Environment and Outlook

2019 ◽  
Vol 28 (8) ◽  
pp. 1789-1850 ◽  
Author(s):  
Esmaeil Sadeghi ◽  
Nicolaie Markocsan ◽  
Shrikant Joshi
Keyword(s):  
High Temperature ◽  
Thermal Spray ◽  
Power Plants ◽  
High Temperature Corrosion ◽  
Thermal Spray Coatings ◽  
Current Status ◽  
Comprehensive Overview ◽  
Biomass Waste ◽  
Corrosion Resistant ◽  
Spray Coatings

Abstract High-temperature corrosion of critical components such as water walls and superheater tubes in biomass/waste-fired boilers is a major challenge. A dense and defect-free thermal spray coating has been shown to be promising to achieve a high electrical/thermal efficiency in power plants. The field of thermal spraying and quality of coatings have been progressively evolving; therefore, a critical assessment of our understanding of the efficacy of coatings in increasingly aggressive operating environments of the power plants can be highly educative. The effects of composition and microstructure on high-temperature corrosion behavior of the coatings were discussed in the first part of the review. The present paper that is the second part of the review covers the emerging research field of performance assessment of thermal spray coatings in harsh corrosion-prone environments and provides a comprehensive overview of the underlying high-temperature corrosion mechanisms that lead to the damage of exposed coatings. The application of contemporary analytical methods for better understanding of the behavior of corrosion-resistant coatings is also discussed. A discussion based on an exhaustive review of the literature provides an unbiased commentary on the advanced accomplishments and some outstanding issues in the field that warrant further research. An assessment of the current status of the field, the gaps in the scientific understanding, and the research needs for the expansion of thermal spray coatings for high-temperature corrosion applications is also provided.

Investigation of the Down-Scaling Effects on the Low Swirl Burner and its Application to Microturbines

2018 ◽  
Author(s):  
Alex Frank ◽  
Peter Therkelsen ◽  
Miguel Sierra Aznar ◽  
Vi H. Rapp ◽  
Robert K. Cheng ◽  
...  
Keyword(s):  
Power Systems ◽  
Power Plants ◽  
Energy Savings ◽  
The United States ◽  
Primary Energy ◽  
Department Of Energy ◽  
Small Scale ◽  
United States Department ◽  
Scaling Effects ◽  
Swirl Burner

About 75% of the electric power generated by centralized power plants feeds the energy needs from the residential and commercial sectors. These power plants waste about 67% of primary energy as heat emitting 2 billion tons of CO2 per year in the process (∼ 38% of total US CO2 generated per year) [1]. A study conducted by the United States Department of Energy indicated that developing small-scale combined heat and power systems to serve the commercial and residential sectors could have a significant impact on both energy savings and CO2 emissions. However, systems of this scale historically suffer from low efficiencies for a variety of reasons. From a combustion perspective, at these small scales, few systems can achieve the balance between low emissions and high efficiencies due in part to the increasing sensitivity of the system to hydrodynamic and heat transfer effects. Addressing the hydrodynamic impact, the effects of downscaling on the flowfield evolution were studied on the low swirl burner (LSB) to understand if it could be adapted to systems at smaller scales. Utilizing particle image velocimetry (PIV), three different swirlers were studied ranging from 12 mm to 25.4 mm representing an output range of less than 1 kW to over 23 kW. Results have shown that the small-scale burners tested exhibited similar flowfield characteristics to their larger-scale counterparts in the non-reacting cases studied. Utilizing this data, as a proof of concept, a 14 mm diameter LSB with an output of 3.33 kW was developed for use in microturbine operating on a recuperated Brayton cycle. Emissions results from this burner proved the feasibility of the system at sufficiently lean mixtures. Furthermore, integration of the newly developed LSB into a can style combustor for a microturbine application was successfully completed and comfortably meet the stringent emissions targets. While the analysis of the non-reacting cases was successful, the reacting cases were less conclusive and further investigation is required to gain an understanding of the flowfield evolution which is the subject of future work.

scholarly journals Experimental investigation of an annular diffuser for axial fans at different inflow profiles

2017 ◽  
Vol 21 (suppl. 3) ◽  
pp. 553-564
Author(s):  
Johannes Walter ◽  
Dieter Wurz ◽  
Stefan Hartig ◽  
Martin Gabi
Keyword(s):  
Power Plants ◽  
High Efficiency ◽  
Outer Wall ◽  
Pressure Recovery ◽  
Shear Stresses ◽  
Axial Fan ◽  
Mean Velocity ◽  
Annular Diffuser ◽  
Axial Fans ◽  
Wall Shear

Axial fans are used in power plants for fresh air supply and flue gas transport. A typical configuration consists of an axial fan and annular diffuser which connects the fan to the following piping. In order to achieve a high efficiency of the con-figuration, not only the components have to be optimized but also their interaction. The present study focuses on the diffuser of the configuration. Experiments are performed on a diffuser-piping configuration to investigate the influence of the velocity profile at the fan outlet on the pressure recovery of the configuration. Two different diffuser inlet profiles are generated, an undisturbed profile and a profile with the typical outlet characteristics of a fan. The latter is generated by the superposition of screens in the inlet zone. The tests are conducted at a high Reynolds number (Re ? 4?105). Mean velocity profiles and wall shear stresses are measured with hydraulic methods (Prandtl and Preston tubes). The results show that there is a lack of momentum at the outer wall of the diffuser and high shear stresses at the inner wall in case of the undisturbed inflow profile. For the typical fan outlet profile it is vice versa. There are high wall shear stresses at the outer wall while the boundary layer of the inner wall lacks momentum. The pressure recovery of the undisturbed inflow configuration is in good agreement with other studies.

Sign in / Sign up

Export Citation Format

Share Document