Seven-Port Unequal Power Divider with Broadband and Large Division Ratio Characteristics Based on T-shape Stub

Frequenz ◽  
2017 ◽  
Vol 71 (11-12) ◽  
Author(s):  
Xing Jiang ◽  
Jia Wei ◽  
Lin Peng ◽  
Shao-Yu Tang
Keyword(s):  
Line Width ◽  
Theoretical Basis ◽  
Matrix Algebra ◽  
Characteristic Impedance ◽  
Power Divider ◽  
Division Ratio ◽  
Conventional Design ◽  
Good Agreement

AbstractA broadband seven-port unequal power divider with large division ratio is designed based on the technique of T-shape stub. A T-shape stub is introduced to replace the conventional design for high characteristic impedance line in realization due to very small line width. The theoretical basis of the proposed T-shape stub is analyzed in detail using the Method of Matrix Algebra Analysis. The proposed design is simulated, fabricated and measured. The measured results are in good agreement with the simulated ones, and a large division ratio of 1:6 is achieved. The operation bandwidth of the proposed design is about 12 % (from 4.8 to 5.4 GHz).

scholarly journals Unlimited Power Division Ratio of Microstrip Balanced-to-Unbalanced Gysel-Type Arbitrary Power Divider

Electronics ◽  
2020 ◽  
Vol 9 (7) ◽  
pp. 1124
Author(s):  
Zihui Zhu ◽  
Zhongbao Wang ◽  
Ye Fu ◽  
Shaojun Fang ◽  
Hongmei Liu ◽  
...  
Keyword(s):  
Characteristic Impedance ◽  
Power Divider ◽  
Power Dividers ◽  
Arbitrary Power ◽  
Division Ratio ◽  
Mode Suppression ◽  
High Impedance ◽  
Form Design ◽  
The Common ◽  
Good Agreement

A microstrip balanced-to-unbalanced (BTU) Gysel-type arbitrary power divider without the high-impedance transmission-line (TL) section is proposed to eliminate the power division ratio (PDR) limit of the conventional microstrip BTU power dividers. The proposed circuit includes five moderate-impedance TLs having the same characteristic impedance in addition to a grounded resistor. The arbitrary PDR is easily obtained by varying the electrical length of the TLs without changing the characteristic impedances, especially the large PDR, which is difficult to achieve by means of conventional BTU power dividers. When the PDR is ∞, the proposed circuit becomes a balun. The closed-form design equations are derived and discussed. To verify the proposed circuit, three prototypes I, II, and III are designed and fabricated for PDRs of 10 dB, 20 dB, and ∞ dB, respectively. The measured PDRs are in good agreement with the simulations. The measured isolation between the output ports is higher than 31 dB for prototypes I and II. The measured insertion loss of the balun prototype is 0.194 dB. Furthermore, the common-mode suppression of greater than 32 dB and the return loss of higher than 22 dB are obtained for various PDRs.

Compact power divider based on half mode substrate integrated waveguide (HMSIW) with arbitrary power dividing ratio

2016 ◽  
Vol 9 (3) ◽  
pp. 515-521 ◽  
Author(s):  
Ali-Reza Moznebi ◽  
Kambiz Afrooz
Keyword(s):  
High Power ◽  
Three Dimensional ◽  
Power Divider ◽  
Substrate Integrated Waveguide ◽  
Arbitrary Power ◽  
Division Ratio ◽  
Planar Circuits ◽  
3D Em ◽  
Good Agreement ◽  
Microstrip Feed

Design and realisation of a compact power divider based on half mode substrate integrated waveguide (HMSIW) with an arbitrary power dividing ratio is presented. This design consists of a substrate integrated waveguide (SIW) transition, two bisected HMSIW transitions by a gap, an SIW-to-microstrip transition, and two microstrip feed lines. In addition, a resistor is attached between two HMSIW transitions. To adjust the power division ratio, four parameters are introduced. Furthermore, four graphs are plotted using a three-dimensional electronmagnetic (3D EM) simulator to graphically determine the introduced parameters. In this study, three circuits with power division ratios of 1:1, 1:4, and 1:8 are simulated using the 3D EM simulator and fabricated on a Rogers RO4003C substrate. The results show a good agreement between the simulated and measured results. The measured results display these circuits (1:1, 1:4, and 1:8) have the bandwidths of 70, 36, and 40%, respectively. Moreover, the proposed structures (1:1, 1:4, and 1:8) are compact and their overall sizes are$1.13 \times 1.04\lambda _g^2 $,$0.96 \times 0.91\lambda _g^2 $, and$0.81 \times 0.78\lambda _g^2 $, respectively. These structures have the advantages of the compactness in size, wide bandwidth, high power division ratio (from 1:1 to 1:16), and compatibility with planar circuits.

scholarly journals Compact Unequal Power Divider with Filtering Response

2015 ◽  
Vol 2015 ◽  
pp. 1-7
Author(s):  
Wei-Qiang Pan ◽  
Jin-Xu Xu ◽  
Kai Xu Wang ◽  
Xiao Lan Zhao
Keyword(s):  
Antenna Arrays ◽  
Coupling Strength ◽  
Characteristic Impedance ◽  
Power Divider ◽  
Power Dividers ◽  
Division Ratio ◽  
Transmission Zeros ◽  
Compact Size ◽  
Filtering Function ◽  
Wilkinson Power Dividers

We present a novel unequal power divider with bandpass responses. The proposed power divider consists of five resonators and a resistor. The power division ratio is controlled by altering the coupling strength among the resonators. The output ports have the characteristic impedance of 50 Ω and impedance transformers in classical Wilkinson power dividers are not required in this design. Use of resonators enables the filtering function of the power divider. Two transmission zeros are generated near the passband edges, resulting in quasielliptic bandpass responses. For validation, a 2 : 1 filtering power divider is implemented. The fabricated circuit size is 0.22λg × 0.08λg, featuring compact size for unequal filtering power dividers, which is suitable for the feeding networks of antenna arrays.

scholarly journals Multi-way differential power divider with microstrip output interfaces

2020 ◽  
Vol 71 (4) ◽  
pp. 274-280
Author(s):  
Cheng-Guang Sun ◽  
Jia-Lin Li ◽  
Baidenger Agyekum Twumasi
Keyword(s):  
Characteristic Impedance ◽  
Theoretical Data ◽  
Power Divider ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Power Dividers ◽  
Quarter Wavelength ◽  
Insertion Losses ◽  
Better Than ◽  
Good Agreement

AbstractThe design and implementation of planar multi-way differential power dividers remain a challenge in terms of the compactness and especially, for the achievable characteristic impedance of the quarter-wavelength transformer when considering large number of outputs. In this work, the double-sided parallel stripline is recommended to realize such a power divider with out-of-phase outputs, and explicit design methods are provided. The proposed multi-way power divider was developed without the use of lump elements on a single substrate. For system applications, a prototype operating at 41.6 MHz with 12 pairs of out-of-phase outputs that utilize the microstrip line as the output interfaces was fabricated and examined. At the center frequency of 41.6MHz, the developed prototype measured insertion losses akin to 14.3 dB as compared with the theoretical data of 13.8 dB. The attainable impedance bandwidth ranges from 10 MHz to 80 MHz under a magnitude imbalance of ±0.3 dB. The isolations of the adjacent outputs are about 13.1 dB as compared with the theoretical values of 14.428 dB, and are better than 34 dB for more distant ones. Parameter measurements are in good agreement with the numerical predications, thus demonstrating the realization of the proposed multi-way power divider.

Tunable balanced to balanced filtering power divider with high common-mode suppression

Frequenz ◽  
2020 ◽  
Vol 74 (7-8) ◽  
pp. 263-270
Author(s):  
Cao Zeng ◽  
Xue Han Hu ◽  
Feng Wei ◽  
Xiao Wei Shi
Keyword(s):  
Return Loss ◽  
High Selectivity ◽  
Power Divider ◽  
Center Frequency ◽  
Differential Mode ◽  
Common Mode ◽  
Mode Suppression ◽  
The Common ◽  
Equal Power ◽  
Good Agreement

AbstractIn this paper, a tunable balanced-to-balanced in-phase filtering power divider (FPD) is designed, which can realize a two-way equal power division with high selectivity and isolation. A differential-mode (DM) passband with a steep filtering performance is realized by applying microstrip stub-loaded resonators (SLRs). Meanwhile, six varactors are loaded to the SLRs to achieve the center frequency (CF) and bandwidth adjustment, respectively. U-type microstrip lines integrated with stepped impedance slotline resonators are utilized as the differential feedlines, which suppress the common-mode (CM) intrinsically, making the DM responses independent of the CM ones. A tuning center frequency from 3.2 to 3.75 GHz and a fractional bandwidth (12.1–17.6%) with more than 10 dB return loss and less than 2.3 dB insertion loss can be achieved by changing the voltage across the varactors. A good agreement between the simulated and measured results is observed. To the best of authors' knowledge, the proposed balanced-to-balanced tunable FPD is first ever reported.

Analysis of Characteristic of Microstrip Signal Loss in Course of Signal Transmission

2011 ◽  
Vol 194-196 ◽  
pp. 2229-2232
Author(s):  
Qing Song Xiong ◽  
Zhao Hua Wu ◽  
Pin Chen ◽  
Sheng Zhang
Keyword(s):  
Line Width ◽  
Transmission Lines ◽  
Coupling Effect ◽  
Signal Transmission ◽  
Characteristic Impedance ◽  
Signal Loss ◽  
Scattering Parameters ◽  
Scattering Parameter ◽  
Conductor Loss ◽  
Strip Lines

The effect of loss of transmission line on the transmission signal can’t be ignored in microwave circuits. Based on the theory of loss and microwave network principle, the effect of the width, parallel length and space of transmission lines on the scattering parameters’ insertion loss is analyzed in perspective of scattering parameters of the odd mode and even mode. The simulation results show that: when the other parameters are fixed, both the characteristic impedance and the conductor loss decrease non-linearly with the line width broadening; due to the coupling effect between micro-strip lines, the first trough frequency of the scattering parameter S21 curved line, that is the point the signal energy attenuate most seriously, decreases linearly with line width broadening and increases non- linearly with line spaces broadening.

A Filtering Power Divider with Tunable Center Frequency and Wide Stopband

Frequenz ◽  
2019 ◽  
Vol 73 (9-10) ◽  
pp. 301-306
Author(s):  
Xuehan Hu ◽  
Feng Wei ◽  
Jiawen Hao ◽  
Xiaowei Shi
Keyword(s):  
Design Method ◽  
Power Divider ◽  
Center Frequency ◽  
Electrical Length ◽  
Transmission Zeros ◽  
Quarter Wavelength ◽  
Varactor Diodes ◽  
Measurement Results ◽  
Band Pass ◽  
Good Agreement

AbstractIn this paper, a tunable power divider (PD) with a good band-pass filtering response using quarter-wavelength stepped impedance resonators (SIRs) is presented. By appropriately adjusting the impedance and electrical length ratio of SIR, the proposed structure can achieve wide stopband performance. Meanwhile, four varactor diodes are loaded to the external resonators to achieve electrical reconfiguration. In addition, a pair of transmission zeros (TZs) can be generated by applying source and load coupling on each side of the passband, which can effectively improve passband selectivity and out-of-band rejection. In order to verify the feasibility of the proposed design method, a prototype circuit of the proposed filtering power divider (FPD) with tunable center frequency is simulated, fabricated and measured. A good agreement between the simulation and measurement results is observed.

scholarly journals Compact and Broadband Microstrip Band-Stop Filters with Single Rectangular Stubs

2019 ◽  
Vol 9 (2) ◽  
pp. 248 ◽  
Author(s):  
Yusuke Kusama ◽  
Ryota Isozaki
Keyword(s):  
Microstrip Line ◽  
Reverse Flow ◽  
Characteristic Impedance ◽  
Quarter Wavelength ◽  
Band Stop Filter ◽  
Radial Stub ◽  
5 Ghz ◽  
Rf Signal ◽  
Narrow Gaps ◽  
Good Agreement

In this research, a compact and broadband microstrip line quarter-wavelength open circuited stub, which is the core of the band-stop filter, is studied from the viewpoint of the characteristic impedance ratio between the main transmission line and the stub line. Furthermore, a circuit pattern in which an inductive diaphragm is inserted at the stub attachment point using a stepped impedance structure is examined, and an evaluation of frequency adjustment and miniaturization is investigated. The results are compared with the well-known radial stub. Good agreement was obtained between the measured and simulated values up to 5 GHz. Good stop bandwidth was obtained, and the validity of the proposed method is confirmed. The application to other frequency bands is straightforward. The proposed structure is applicable as an alternative to the existing radial stub used for bias T to prevent the reverse flow of the Radio frequency (RF) signal to direct current (DC) source. It is also applicable for the waveguide E-plane band-stop filter, for preventing unwanted leakage from narrow gaps by substituting to a short-circuited stub with a capacitive window, by using the same approach used in the microstrip line H-plane discontinuity.

A novel balanced-to-balanced power divider based on three-line coupled structure

2019 ◽  
Vol 11 (2) ◽  
pp. 139-142
Author(s):  
Zhen Tan ◽  
Qing-Yuan Lu ◽  
Jian-Xin Chen
Keyword(s):  
Equivalent Circuit ◽  
Design Procedure ◽  
Power Divider ◽  
Equivalent Circuits ◽  
Differential Mode ◽  
Detailed Design ◽  
Symmetrical Structure ◽  
The Common ◽  
First Time ◽  
Good Agreement

AbstractThis paper presents a novel balanced-to-balanced power divider (PD) based on a simple and compact three-line coupled structure for the first time. By bisecting the proposed symmetrical structure, the differential mode (DM) and the common mode (CM) equivalent circuits can be obtained for analysis. The DM equivalent circuit exhibits a three-line in-phase power dividing response, and then a resistor is added between the two outputs for achieving good isolation. Meanwhile, the CM equivalent circuit shows a three-line all-stop response so that the CM suppression in this design does not need to be considered. Accordingly, the detailed design procedure of the DM PD is given. For demonstration, a prototype centered at 1.95 GHz is designed, fabricated, and measured. The simulated and measured results with good agreement are presented, showing low DM loss and wideband CM suppression.

scholarly journals Highly Unequal Three-Port Power Divider: Theory and Implementation

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Duolong Wu ◽  
Adriana Serban ◽  
Magnus Karlsson ◽  
Shaofang Gong
Keyword(s):  
Transmission Lines ◽  
Directional Coupler ◽  
Feedback Mechanism ◽  
Power Divider ◽  
Electromagnetic Simulation ◽  
Planar Form ◽  
Measurement Results ◽  
Minimum Number ◽  
Wilkinson Power Divider ◽  
Good Agreement

A three-port power divider consisting of a directional coupler, a Wilkinson power divider, and two transmission lines connected to them is proposed. Theoretical analysis reveals that highly unequal power division can be achieved by a feedback mechanism of two transmission lines along with the coupling coefficient of the directional coupler and the power division ratio of the Wilkinson power divider. The three-port power divider inherits the performance characteristics of high isolation, low reflection coefficients at all ports, and the minimum number of components. The proposed power divider is designed at 5.8 GHz and fabricated and evaluated through measurements. It demonstrates that electromagnetic simulation results are in good agreement with theoretical prediction and measurement results. The three-port power divider is compact in the planar form, so it can be easily integrated into radio frequency front ends.

Sign in / Sign up

Export Citation Format

Share Document