Effect of Protein and Polysaccharide-Based Edible Coatings on Quality of Kiwifruit (Actinidia deliciosa) During Drying

Author(s):  
De Oliveira ◽  
Keila de S. Silva

AbstractThe aim of the present study was to evaluate the application of three different edible coatings as pretreatment to drying and their influence on mass transfer kinetics, vitamin C retention and color preservation during process. Therefore, part of the slices of kiwifruit was covered with the pectin (with and without glycerol), another part was covered with the soy protein isolate and the rest of the samples were used as control, before the drying process at 60 °C and 70 °C. Vitamin C, color and water content were analyzed before and after the drying. Fick’s model and Page model were fitted to the experimental data obtained in drying process. The results highlighted the potential of using edible coating as an alternative to obtain high-quality dried food, reducing vitamin C losses and the darkening of the product without affecting the mass transfer during hot air drying.

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 516
Author(s):  
Roghieh Sakooei-Vayghan ◽  
Seyed Hadi Peighambardoust ◽  
Rubén Domínguez ◽  
Mirian Pateiro ◽  
José M. Lorenzo

The effect of different composite coatings on quality of semi-moist apricot cubes mixed with cornflakes was investigated during 180 days of storage. The apricot cubes were osmotically dehydrated (OD) and coated before hot-air drying (HAD) at 60 °C. Chitosan-bees wax (CBW) and whey protein isolate-bees wax-oleic acid (WPI-BW-OA) coatings were applied after HAD and the samples were added to cornflakes. Application of OD and pectin-ascorbic acid (Pec-AA) coating (prior to HAD) and WPI-BW-OA coating (after HAD) led to significant retention of total phenol compounds, β-carotene and antioxidant activity in apricot cubes compared to uncoated and CBW-coated samples. WPI-BW-OA-coated samples gave significantly higher L* values (lighter color) and b* values (more creamy or yellowish color) and lower a* values (less reddish color) and browning values than control followed by CBW-coated apricots at any time of storage (p < 0.05). The rate of apricot moisture loss and cornflakes moisture gain was higher in uncoated apricot cubes, followed by CBW- and WPI-BW-OA-coated samples. Application of WPI-BW-OA coating was effective in retaining the crispness measured by lower firmness (Fmax) values in cornflakes upon storage. Based on the obtained results, WPI-BW-OA coating allowed effectively preserving the quality characteristics of semi-moist apricot cubes and cornflakes components in the mixed state.


2020 ◽  
Vol 122 (10) ◽  
pp. 3227-3238
Author(s):  
Sharmila Vengu ◽  
Haswini Paniker Ravandran ◽  
Sri Puvanesvari Gannasin ◽  
Kharidah Muhammad

PurposeDeep-fried banana (Musa spp.) fritters is one of the frequently consumed fruit based snacks in Southeast Asian countries despite its substantial amount of oil content. Consistent with the demand for low fat food with maintained palatability, this study aimed to determine the quality of banana fritters as affected by batter system containing selected hydrocolloids such as pectin (PCN), whey protein isolate (WPI) and soy protein isolate (SPI).Design/methodology/approachBanana fritter batters were prepared with individual addition of 2% PCN (w/w), 10% WPI (w/w), 10% SPI (w/w), combination of 2% PCN and 10% WPI, combination of 2% PCN and 10% SPI and control (without hydrocolloid addition). Batter viscosity (Pa.s) and batter pick-up (%) were determined. Banana fritters were analysed for moisture and fat contents, moisture loss, colour, hardness and sensory characteristics.FindingsHydrocolloid addition in the batter system resulted in a higher batter pick-up and viscosity in comparison to control batter system. Moisture loss from banana fritters with batter formulation of 2% PCN and 10% SPI was the lowest while the reduction in oil content (55%) was the highest. Banana fritters with inclusion of hydrocolloids in the batter formulation were equally accepted as the control sample by the sensory panelists with a score range between 6 and 7 for most of the sensory attributes evaluated except for oiliness.Originality/valueApplication of PCN and SPI in batter system to develop banana fritters with low oil content, moist fruit core and crunchy crust is reported for the first time. Batter premix containing PCN and SPI can be produced for fresh and frozen fritters preparation.


2019 ◽  
Vol 30 (5) ◽  
pp. 2639-2653
Author(s):  
Jongrak Choi ◽  
Giyeob Yang ◽  
Nahmkeon Hur

Purpose Paint drying is a very important process in an industry where shorter drying time for productivity and lower energy consumption for production cost are required while maintaining the product’s painting quality. In the present study, a drying process in a line-type paint drying furnace equipped with nozzles for hot air supply and moving conveyer belt to dry painted automotive parts is numerically simulated for the flow and heat transfer inside the furnace to evaluate the quality of the drying or baking at the end of the drying process in a production line. Design/methodology/approach A baking window for a specific paint is used for judging the local degree of baking (DOB) of the painted parts, which can be useful to identify under-baked or over-baked locations of the painted parts, and hence the quality of the baking process. Findings Numerical results of a time history of temperatures at two monitoring points on the painted parts were obtained and compared to the measured data in an actual furnace and showed good agreement. Three types of paints were considered in the present study and numerical results showed different drying characteristics. In addition to the original furnace nozzle configuration, two more furnace nozzle configurations with different numbers, direction and speed of hot air supply were simulated to improve the furnace’s drying performance. As a result, a newly suggested nozzle configuration with quick drying paint can give us a remarkable improvement in surface averaged DOB compared to the original nozzle configuration with original paint. Originality/value The present simulation technique and DOB methodology can be used for the optimal design of a drying furnace.


Foods ◽  
2020 ◽  
Vol 9 (12) ◽  
pp. 1877
Author(s):  
Yue Xu ◽  
Zhongjiang Wang ◽  
Baokun Qi ◽  
Anqi Ran ◽  
Zengwang Guo ◽  
...  

Chiba tofu is a new type of vegetarian food prepared with soy protein isolate (SPI). According to factory feedback, the SPI stored in the factory storeroom in summer undergoes reactive oxidation, which changes the structure of SPI and further affects the quality of Chiba tofu. Consequently, the main objective of this study was to prepare Chiba tofu with SPI with different storage periods and evaluate the effect of different degrees of oxidation on structural characteristics of SPI and rheology, texture, microstructure and sensory properties of Chiba tofu. The carbonyl content and turbidity of SPI significantly increased, and the contents of free sulfhydryl (SH) and disulfide bond (S-S) simultaneously decreased with storage time. The oxidation changes the SPI conformation, leading to a transition of α-helix and β-turn to β-sheet and random coil during the storage periods. In the SDS–PAGE analysis, oxidation promoted the SPI molecules crosslinked and aggregated, which affected the quality of Chiba tofu. In short storage periods (0–12 days), SPI was relatively moderately oxidized when the carbonyl content was between 4.14 and 6.87 mmol/g. The storage and loss modulus of Chiba tofu both increased, the network was compact, and the hardness and springiness of Chiba tofu showed an increasing trend. Moreover, in longer storage periods (12–30 days), the SPI was relatively severely oxidized when the carbonyl content was between 7.24 and 9.14 mmol/g, which had an adverse effect on Chiba tofu rheological and texture properties, microstructure, and sensory properties. In sensory evaluation, Chiba tofu stored 12 days had the highest overall quality score than that stored on other days. This study is expected to provide an argument for the better industrial production of Chiba tofu.


2019 ◽  
Vol 56 (9) ◽  
pp. 4166-4176 ◽  
Author(s):  
Kai-Qi Gang ◽  
Zi-Xuan Wu ◽  
Da-Yong Zhou ◽  
Qi Zhao ◽  
Xin Zhou ◽  
...  

2018 ◽  
Vol 17 (03) ◽  
pp. 69-76
Author(s):  
Thien T. Le

Acerola fruit is known to have a high vitamin C concentration. Polyphenolics are also natural oxidants occurring in plants. Understanding changes of these components during storage conditions and processing steps become important. Results of this research showed that there was significant difference in vitamin C and total polyphenolic concentration and three popular varieties of acerola fruits from Tien Giang province. Concentrations of both vitamin C and polyphenolics reduced rapidly during storage at room temperature. After three days, vitamin C reduced about 40% whereas total polyphenolics reduced about 70%. The losses at refrigerated temperature after 3 days were less than 15% and less than 30%, for vitamin C and total polyphenolics, respectively. Frozen storage of the fruit maintained quite well vitamin C and polyphenolics. Acerola pomace juice was concentrated before spray drying and, at the same vacuum pressure, temperatures influenced significantly the retention of vitamin C and total polyphenolics. Optimization of spray drying conditioners including inlet hot air temperatures and added ratio of maltodextrin (drying carrier) was also carried out to obtain high recovery of dry matter, total polyphenolics and vitamin C.


2018 ◽  
Author(s):  
◽  
Faith Seke

Celiac disease (CD) is an auto-immune disorder that is triggered by the consumption of gluten in predisposed individuals. The only remedy that has been proposed thus far is total exclusion of gluten from the diet. This may be the most difficult task to most celiac disease patients for most of the convenient and widely consumed baked products such as bread are prepared using ingredients that contain gluten. The replacement of gluten in the baking industry comes with some implications on the overall quality of the baked products, especially bread. It has been observed that gluten-free baked products currently on the market are of poor texture, less volume, not visually appealing and have a bad taste. Hence, the need for polymeric substances that can mimic gluten properties, yielding baked products with similar characteristics as the gluten-containing counterparts. Various crops such as rice, sorghum, sweet potato and cassava have been used and additives such as hydrocolloids, protein-based ingredients, emulsifiers and enzymes included to improve gluten-free bread quality. The use of carbohydrate-rich tubers and protein-rich legumes as gluten-free ingredients shows great potential in the food industry. Amadumbe (Colocasia esculenta) is a carbohydrate rich tuber which is highly underutilized in South Africa and contains vast amounts of mucilage, a hydrocolloid which can be of great help to improve dough rheology. Hydrocolloids have been reported in literature to have the ability of improving dough water holding capacity and improving dough viscosity hence facilitating gas retention and impacting on the overall quality of the baked product. However, despite the presence of mucilage, amadumbe is very low in protein and it is difficult to produce bread with properties that resemble gluten-containing bread. Hence the need for protein supplementation which may also potentially facilitate protein cross-linking during bread making. Legume proteins from crops such as soy bean and bambara groundnuts contain abundant quantities of lysine, tyrosine and cysteine which could potentially be manipulated through the use of enzymes such as laccase in order to initiate the formation of a network similar to gluten. The project investigated the effect of laccase and xanthan gum (a hydrocolloid) on the quality of gluten-free bread supplemented with bambara groundnut flour and soy protein isolate as protein sources. Flour blends were prepared using a ratio of 70:30 (amadumbe flour: bambara groundnut flour) and 88:12 (amadumbe flour: soy protein isolate) based on a targeted protein content of 16 g/100 g and the quality properties were determined. Colour analysis showed that amadumbe flour had a higher L* value compared to the other flours and the blends, showing that amadumbe can be used in applications where food colour contributes to food perceptions. However, when bambara groundnut flour and soy protein isolate were added the L* value decreased. The nutritional profile of the individual flours and the blends showed that amadumbe flour protein content was improved with the addition of bambara groundnut flour and soy protein isolate in the above-mentioned ratios. The protein content of amadumbe increased from 2.36 g/100 g to 15.87 g when bambara groundnut flour was added and to 16.10 g/100 g when soy protein isolate was added, values that were close to the targeted protein content. Incorporating bambara groundnut flour and soy protein isolate in amadumbe flour resulted in improved water absorption capacity, foam capacity and stability as well as emulsion capacity and stability of the amadumbe flour. However, there was no significant difference in oil absorption capacity between amadumbe flour and the blends. The blends were then used to formulate different bread samples incorporating the enzyme laccase (25 nkat/g flour) and a hydrocolloid, xanthan gum (1%). Laccase-mediated treatment of gluten-free amadumbe dough resulted in a 30% decrease in the free sulfhydryl groups and a 40% decrease in phenolic content indicating that crosslinking had occurred. Laccase action resulted in a 64% increase in bread specific volume and a 32% decrease in bread crumb hardness. Sensory analysis showed that laccase-treated bread samples were more acceptable compared to the non-treated bread samples in terms of appearance, texture, aroma and taste. The acceptability index varied between 46% and 86.2%. This study showed that there is great potential of laccase in gluten-free bread making. The addition of 1% xanthan gum to amadumbe dough supplemented with bambara groundnut flour and soy protein isolate resulted in gluten-free amadumbe bread with improved crumb texture and specific volume, and decreased the rate of moisture loss. Sensory analysis also revealed that gluten-free amadumbe bread with added xanthan gum was more acceptable compared to the bread samples without xanthan gum. The acceptability index of the bread samples ranged between 40% and 85%. The resulting bread with xanthan gum showed that hydrocolloids such as xanthan gum can be successfully used in the development of gluten-free baked products. Overall, this study has shown that the incorporation of laccase and xanthan gum to gluten-free amadumbe bread results in bread with improved and acceptable bread properties.


Today many industries now use the dryer as a part of grain-drying process even during wet and dry seasons. This helps in reducing spoilage and wastage of paddy. Mostly the available industrial dryers are expensive to purchase and to maintain its smooth functioning. This study therefore is a step to design a simple Plug flow fluidized dryer that can lead to introduce small scale dryers to paddy process industry. The Plug flow fluidized bed dryers are designed and fabricated in this study consists of the drying chamber, hot air distributer plate, hot air inlet and exit system, paddy entry and exit system, fluidization chamber unit with temperature control unit and the centrifugal fan. The evaluation of dryer is based on drying time and reduction in moisture content and outlet temperature of paddy on quality parameters. Dryer dimensions are very important to analyze heat and mass transfer analysis of the Plug flow fluidized bed drying process of paddy grains. It was found d that heat and mass transfer properties of paddy grains in fluidized bed dryer was decreases as the time of drying passes and very rapid at the start of drying. The model present here predicts about dryer dimensions along safe zone of rough rice moisture content with other parameters. Simulation results show a good agreement between the simulation model and the existing simulation models


2012 ◽  
Vol 55 (1) ◽  
pp. 27-34 ◽  
Author(s):  
Jin-Han Shon ◽  
Jin-Ho Kim ◽  
Ji-Hyun Eo ◽  
Yong-Hwa Choi

2016 ◽  
Vol 10 (1) ◽  
pp. 64-69
Author(s):  
Fauziati Fauziati ◽  
Yuni Adiningsih ◽  
Ageng Priatni

Edible coatings represent preservation techniques also function as a packaging material that is applied directly to food items including fruits. Its use is intended to extend the shelf life and improve the quality of food products and is biodegradable materials that are more environmentally friendly. Research Stearin use as edible coating on citrus fruits have been done. The use of stearin used was 0%, 0.1% and 0.2% combined with gelatin at a fixed amount that is 2 g. Edible coatings applied to citrus fruit which gained the best results are stearin 0.1% with test results shrinkage lowest weight on day 12 amounted to 5.598% for the treatment of immersion and can retain the vitamin C content of 40.3 mg / 100 g and can maintain antioksioksidan to 12 days with the antioxidant content of 74.7%.ABSTRAKEdible coating merupakan teknik pengawetan sekaligus berfungsi sebagai bahan pengemasan yang diaplikasikan secara langsung pada bahan pangan termasuk buah buahan. Penggunaannya dimaksudkan untuk memperpanjang masa simpan dan memperbaiki kualitas produk pangan serta merupakan bahan yang biodegradable sehingga lebih ramah lingkungan. Penelitian penggunaan Stearin kelapa sawit sebagai edible coating pada buah jeruk telah dilakukan. Penggunaan stearin yang digunakan adalah 0%, 0.1% dan 0.2% yang dikombinasikan dengan gelatin dengan jumlah tetap yaitu 2 g. Edible coating diaplikasikan ke buah jeruk dimana diperoleh hasil terbaik yaitu stearin 0.1% dengan hasil uji susut bobot terendah pada hari ke 12 sebesar 5.598% untuk perlakuan celup dan dapat mempertahankan kandungan vitamin C sebesar 40.3 mg/100 gr serta dapat mempertahankan antioksioksidan sampai 12 hari dengan kandungan antioksidan 74.7%. Kata kunci : Stearin, Edible Coating, buah jeruk 


Sign in / Sign up

Export Citation Format

Share Document