Utilisation of Chemical Waste Additives with Low Octane Commercial Gasoline Fuel to Enhance the Performance of SI Engines

2021 ◽  
Vol 18 (1) ◽  
pp. 8612-8620
Author(s):  
O. M. Ali
Keyword(s):  
Wavelet Analysis ◽  
Gasoline Engine ◽  
Waste Product ◽  
Engine Performance ◽  
Operating Conditions ◽  
Optimum Operating ◽  
Chemical Waste ◽  
Maximum Increase ◽  
Brake Power ◽  
Cyclic Variations

In this study, fusel oil additive from the waste product has been used as an octane number enhancer to improve gasoline engine performance. The fusel additive was added at 10%, 20% and 30% ratios to prepare the investigated fuel samples (M10, M20 and M30, respectively, in addition to pure gasoline M0). Engine tests were conducted at constant half engine load and increasing speed from 1500 rpm to 4500 rpm at 1000 rpm increments. Response surface methodology has been used as a statistical technique to describe the relationship between the investigated input variables with their responses to achieve the optimum operating conditions. Engine cyclic variations were analysed using wavelet analysis of in-cylinder pressure based on indicated mean effective pressure (IMEP) calculated for 100 consecutive cycles. The results showed that the higher brake power was obtained with blended fuel M20 during the engine operating speeds. The maximum increase of brake power found to be 23.6% with M20 compared to gasoline at 1500 rpm, which accompanied by a 7.3% increase in brake specific fuel consumption. On the other hand, the highest increase in brake thermal efficiency is found to be related to the engine speed and fusel additive ratio. Wavelet analysis shows that the engine cyclic variations decrease as the fusel additive introduce with gasoline. Moreover, fusel additive has a pronounced effect on decreasing the cycle to cycle variations of the IMEP time series with the lowest overall engine cyclic variations for M30. Accordingly, 20% fusel additive (M20) can be considered as a valuable octane enhancer for better engine performance.

scholarly journals Predicting Cycle-to-Cycle Variation With Concurrent Cycles in a Gasoline Direct Injected Engine With Large Eddy Simulations

2018 ◽  
Author(s):  
Daniel Probst ◽  
Sameera Wijeyakulasuriya ◽  
Eric Pomraning ◽  
Janardhan Kodavasal ◽  
Riccardo Scarcelli ◽  
...  
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Engine Performance ◽  
Turnaround Time ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Cycle Variation ◽  
Spark Timing ◽  
Large Eddy ◽  
Operating Points

High cycle-to-cycle variation (CCV) is detrimental to engine performance, as it leads to poor combustion and high noise and vibration. In this work, CCV in a gasoline engine is studied using large eddy simulation (LES). The engine chosen as the basis of this work is a single-cylinder gasoline direct injection (GDI) research engine. Two stoichiometric part-load engine operating points (6 BMEP, 2000 RPM) were evaluated: a non-dilute (0% EGR) case and a dilute (18% EGR) case. The experimental data for both operating conditions had 500 cycles. The measured CCV in IMEP was 1.40% for the non-dilute case and 7.78% for the dilute case. To estimate CCV from simulation, perturbed concurrent cycles of engine simulations were compared to consecutively obtained engine cycles. The motivation behind this is that running consecutive cycles to estimate CCV is quite time-consuming. For example, running 100 consecutive cycles requires 2–3 months (on a typical cluster), however, by running concurrently one can potentially run all 100 cycles at the same time and reduce the overall turnaround time for 100 cycles to the time taken for a single cycle (2 days). The goal of this paper is to statistically determine if concurrent cycles, with a perturbation applied to each individual cycle at the start, can be representative of consecutively obtained cycles and accurately estimate CCV. 100 cycles were run for each case to obtain statistically valid results. The concurrent cycles began at different timings before the combustion event, with the motivation to identify the closest time before spark to minimize the run time. Only a single combustion cycle was run for each concurrent case. The calculated standard deviation of peak pressure and coefficient of variance (COV) of indicated mean effective pressure (IMEP) were compared between the consecutive and concurrent methods to quantify CCV. It was found that the concurrent method could be used to predict CCV with either a velocity or numerical perturbation. A large and small velocity perturbation were compared and both produced correct predictions, implying that the type of perturbation is not important to yield a valid realization. Starting the simulation too close to the combustion event, at intake valve close (IVC) or at spark timing, under-predicted the CCV. When concurrent simulations were initiated during or before the intake even, at start of injection (SOI) or earlier, distinct and valid realizations were obtained to accurately predict CCV for both operating points. By simulating CCV with concurrent cycles, the required wall clock time can be reduced from 2–3 months to 1–2 days. Additionally, the required core-hours can be reduced up to 41%, since only a portion of each cycle needs to be simulated.

Assessing Double Injection and Intake Air Temperature Effects on Gasoline HCCI Engine Performance and Emissions Using Fully-Automated Experiments and Micro-Genetic Algorithms

2002 ◽  
Author(s):  
Mustafa Canakci ◽  
Eric Hruby ◽  
Rolf D. Reitz
Keyword(s):  
Air Temperature ◽  
Gasoline Engine ◽  
Engine Performance ◽  
Operating Conditions ◽  
Spray Angle ◽  
Injection Timing ◽  
Engine Operation ◽  
Double Injection ◽  
Performance And Emissions ◽  
Engine Performance And Emissions

Homogeneous charge compression ignition (HCCI) is receiving attention as a new low emission engine concept. Little is known about the optimal operating conditions for this engine operation mode. Combustion at homogeneous, low equivalence ratio conditions results in modest temperature combustion products, containing very low concentrations of NOx and PM as well as providing high thermal efficiency. However, this combustion mode can produce higher HC and CO emissions than those of conventional engines. An electronically controlled Caterpillar single-cylinder oil test engine (SCOTE), originally designed for heavy-duty diesel applications, was converted to a HCCI direct-injection gasoline engine. The engine features an electronically controlled low-pressure common rail injector with a 60°-spray angle that is capable of multiple injections. The use of double injection was explored for emission control, and the engine was optimized using fully-automated experiments and a micro-genetic algorithm (μGA) optimization code. The variables changed during the optimization include the intake air temperature, start of injection timing, and split injection parameters (percent mass of the fuel in each injection, dwell between the pulses). The engine performance and emissions were determined at 700 rev/min with a constant fuel flow rate at 10 MPa fuel injection pressure. The results show that significant emissions reductions are possible with the use of optimal injection strategies.

Numerical Investigation of the Effects of Axial Cylinder Bore Profiles on Piston Ring Radial Dynamics

2003 ◽  
Vol 125 (4) ◽  
pp. 1081-1089 ◽  
Author(s):  
Y. Piao ◽  
S. D. Gulwadi
Keyword(s):  
High Speed ◽  
Piston Ring ◽  
Gasoline Engine ◽  
Engine Performance ◽  
Operating Conditions ◽  
Engine Oil ◽  
Oil Consumption ◽  
Ring Pack ◽  
Cylinder Bore

The role of cylinder bore shapes in engine performance has been the subject of several studies in recent years. In particular, the influence of bore distortion on oil consumption under high speed conditions has generated significant interest. In this paper, the effect of an axial bore profile on radial dynamics of a ring is investigated. Radial ring motions within grooves due to the axial bore profile can generate significant inertial effects and also have an impact on ring end-gap sizes and lubrication conditions at the ring-liner interfaces. The magnitude of such effects is dependent on the ring-pack configuration, engine operating conditions (speed and load) and axial bore profile details. These issues are investigated in this study due to their implication on engine oil consumption, friction and blow-by. The authors have developed an analytical expression to account for the effects of radial ring inertia due to an axial bore profile for implementation in a piston ring-pack simulation tool RINGPAK. Simulation results from a gasoline engine study are presented to illustrate the effects of engine speeds, ring tensions, and characteristics of axial bore profiles on ring radial dynamics and ring-liner lubrication. Relevant qualitative comparisons are made to experimental measurements available in the literature.

Experimental and Theoretical Study of Injection Timing on Performance and Exhaust Emissions in a Port-Injected Gasoline Engine

2006 ◽  
Author(s):  
E. Movahednejad ◽  
F. Ommi ◽  
M. Hosseinalipour ◽  
O. Samimi
Keyword(s):  
Gasoline Engine ◽  
Fuel Injection ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Exhaust Emissions ◽  
Operating Conditions ◽  
Exhaust Emission ◽  
Injection Timing ◽  
Intake Port ◽  
One Dimensional

For spark ignition engines, the fuel-air mixture preparation process is known to have a significant influence on engine performance and exhaust emissions. In this paper, an experimental study is made to characterize the spray characteristics of an injector with multi-disc nozzle used in the engine. The distributions of the droplet size and velocity and volume flux were characterized by a PDA system. Also a model of a 4 cylinder multi-point fuel injection engine was prepared using a fluid dynamics code. By this code one-dimensional, unsteady, multiphase flow in the intake port has been modeled to study the mixture formation process in the intake port. Also, one-dimensional air flow and wall fuel film flow and a two-dimensional fuel droplet flow have been modeled, including the effects of in-cylinder mixture back flows into the port. The accuracy of model was verified using experimental results of the engine testing showing good agreement between the model and the real engine. As a result, predictions are obtained that provide a detailed picture of the air-fuel mixture properties along the intake port. A comparison was made on engine performance and exhaust emission in different fuel injection timing for 2600 rpm and different loads. According to the present investigation, optimum injection timing for different engine operating conditions was found.

scholarly journals SI engine performance, lubricant oil deterioration, and emission: A comparison of liquid and gaseous fuel

2020 ◽  
Vol 12 (6) ◽  
pp. 168781402093045
Author(s):  
Muhammad Usman ◽  
Muhammad Wajid Saleem ◽  
Syed Saqib ◽  
Jamal Umer ◽  
Ahmad Naveed ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Natural Gas ◽  
Specific Energy ◽  
Alternative Fuels ◽  
Specific Energy Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Compressed Natural Gas ◽  
Lubricant Oil ◽  
Brake Power

Considering the importance of alternative fuels in IC engines for environment safety, compressed natural gas has been extensively employed in SI engines. However, scarce efforts have been made to investigate the effect of compressed natural gas on engine lubricant oil for a long duration. In this regard, a comprehensive analysis has been made on the engine performance, emissions, and lubricant oil conditions using gasoline ( G)92 and compressed natural gas at different operating conditions using reliable sampling methods. The key parameters of the engine performance like brake power and brake-specific energy consumption were investigated at 80% throttle opening within 1500–4500 range of r/min. For the sake of emission tests, speed was varied uniformly by varying the load at a constant throttle. Furthermore, the engine was run at high and low loads for lubricant oil comparison. Although compressed natural gas showed a decrease in brake-specific energy consumption (7.94%) and emissions content, ( G)92 performed relatively better in the case of brake power (39.93% increase). Moreover, a significant improvement was observed for wear debris, lubricant oil physiochemical characteristics, and additives depletion in the case of compressed natural gas than those of ( G)92. The contents of metallic particles were decreased by 23.58%, 36.25%, 42.42%, and 66.67% for iron, aluminum, copper, and lead, respectively, for compressed natural gas.

Numerical Investigation of the Effects of Axial Cylinder Bore Profiles on Piston Ring Radial Dynamics

2002 ◽  
Author(s):  
Y. Piao ◽  
S. D. Gulwadi
Keyword(s):  
High Speed ◽  
Piston Ring ◽  
Gasoline Engine ◽  
Engine Performance ◽  
Operating Conditions ◽  
Engine Oil ◽  
Oil Consumption ◽  
Ring Pack ◽  
Cylinder Bore

The role of cylinder bore shapes in engine performance has been the subject of several studies in recent years. In particular, the influence of bore distortion on oil consumption under high speed conditions has generated significant interest. In this paper, the effect of an axial bore profile on radial dynamics of a ring is investigated. Radial ring motions within grooves due to the axial bore profile can generate significant inertial effects and also have an impact on ring end-gap sizes and lubrication conditions at the ring-liner interfaces. The magnitude of such effects is dependent on the ring-pack configuration, engine operating conditions (speed and load) and axial bore profile details. These issues are investigated in this study due to their implication on engine oil consumption, friction and blow-by. The authors have developed an analytical expression to account for the effects of radial ring inertia due to an axial bore profile for implementation in a piston ring–pack simulation tool RINGPAK. Simulation results from a gasoline engine study are presented to illustrate the effects of engine speeds, ring tensions and characteristics of axial bore profiles on ring radial dynamics and ring-liner lubrication. Relevant qualitative comparisons are made to experimental measurements available in the literature.

scholarly journals Predicting Cycle-to-Cycle Variation With Concurrent Cycles in a Gasoline Direct Injected Engine With Large Eddy Simulations

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Daniel M. Probst ◽  
Sameera Wijeyakulasuriya ◽  
Eric Pomraning ◽  
Janardhan Kodavasal ◽  
Riccardo Scarcelli ◽  
...  
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Effective Pressure ◽  
Cycle Variation ◽  
Brake Mean Effective Pressure ◽  
Large Eddy ◽  
Operating Points

Abstract High cycle-to-cycle variation (CCV) is detrimental to engine performance, as it leads to poor combustion and high noise and vibration. In this work, CCV in a gasoline engine is studied using large eddy simulation (LES). The engine chosen as the basis of this work is a single-cylinder gasoline direct injection (GDI) research engine. Two stoichiometric part-load engine operating points (6 brake mean effective pressure (BMEP) and 2000 revolutions per minute) were evaluated: a nondilute (0% exhaust gas recirculation (EGR)) case and a dilute (18% EGR) case. The experimental data for both operating conditions had 500 cycles. The measured CCV in indicated mean effective pressure (IMEP) was 1.40% for the nondilute case and 7.78% for the dilute case. To estimate CCV from simulation, perturbed concurrent cycles of engine simulations were compared with consecutively obtained engine cycles. The motivation behind this is that running consecutive cycles to estimate CCV is quite time consuming. For example, running 100 consecutive cycles requires 2–3 months (on a typical cluster); however, by running concurrently, one can potentially run all 100 cycles at the same time and reduce the overall turnaround time for 100 cycles to the time taken for a single cycle (2 days). The goal of this paper is to statistically determine if concurrent cycles, with a perturbation applied to each individual cycle at the start, can be representative of consecutively obtained cycles and accurately estimate CCV. 100 cycles were run for each case to obtain statistically valid results. The concurrent cycles began at different timings before the combustion event, with the motivation to identify the closest time before spark to minimize the run time. Only a single combustion cycle was run for each concurrent case. The calculated standard deviation of peak pressure and coefficient of variance (COV) of IMEP were compared between the consecutive and concurrent methods to quantify CCV. It was found that the concurrent method could be used to predict CCV with either a velocity or numerical perturbation. Both a large and small velocity perturbations were compared, and both produced correct predictions, implying that the type of perturbation is not important to yield a valid realization. Starting the simulation too close to the combustion event, at intake valve close (IVC) or at spark timing, underpredicted the CCV. When concurrent simulations were initiated during or before the intake even, at start of injection (SOI) or earlier, distinct and valid realizations were obtained to accurately predict CCV for both operating points. By simulating CCV with concurrent cycles, the required wall clock time can be reduced from 2–3 months to 1–2 days. In addition, the required core-hours can be reduced up to 41%, since only a portion of each cycle needs to be simulated.

Experimental Evaluation of Turbo-Matching Appropriateness of B60J67, B60J68, A58N70 and A58N72 Turbo-Chargers for a Commercial Vehicle Engine

2018 ◽  
Vol 6 (11) ◽  
pp. 71
Author(s):  
Badal Dev Roy ◽  
R. Saravanan
Keyword(s):  
Internal Combustion Engines ◽  
Perfect Match ◽  
Engine Performance ◽  
Operating Conditions ◽  
Data Logger ◽  
Negative Effects ◽  
Road Test ◽  
The Road ◽  
A Charge ◽  
All Speeds

The Turbocharger is a charge booster for internal combustion engines to ensure best engine performance at all speeds and road conditions especially at the higher load.  Random selection of turbocharger may lead to negative effects like surge and choke in the breathing of the engine. Appropriate selection or match of the turbocharger (Turbomatching) is a tedious task and expensive. But perfect match gives many distinguished advantages and it is a one time task per the engine kind. This study focuses to match the turbocharger to desired engine by simulation and on road test. The objective of work is to find the appropriateness of matching of turbochargers with trim 67 (B60J67), trim 68 (B60J68),  trim 70 (A58N70) and trim 72 (A58N72) for the TATA 497 TCIC -BS III engine. In the road-test (data-logger method) the road routes like highway and slope up were considered for evaluation. The operating conditions with respect various speeds, routes and simulated outputs were compared with the help of compressor map.

Waste to Energy Conversion and Sustainable Recovery of Nutrients from Pee Power - Recent Advancements in Urine-Fed MFCs

2020 ◽  
Vol 17 (7) ◽  
pp. 768-779
Author(s):  
Natarajan Narayanan ◽  
Vasudevan Mangottiri ◽  
Kiruba Narayanan
Keyword(s):  
Power Generation ◽  
Microbial Fuel Cells ◽  
Alternative Energy ◽  
Material Selection ◽  
Waste Product ◽  
Resource Recovery ◽  
Operating Conditions ◽  
Waste To Energy ◽  
Animal Origin ◽  
Human Beings

Microbial Fuel Cells (MFCs) offer a sustainable solution for alternative energy production by employing microorganisms as catalysts for direct conversion of chemical energy of feedstock into electricity. Electricity from urine (urine-tricity) using MFCs is a promising cost-effective technology capable of serving multipurpose benefits - generation of electricity, waste alleviation, resource recovery and disinfection. As an abundant waste product from human and animal origin with high nutritional values, urine is considered to be a potential source for extraction of alternative energy in the coming days. However, developments to improve power generation from urine-fed MFCs at reasonable scales still face many challenges such as non-availability of sustainable materials, cathodic limitations, and low power density. The aim of this paper was to critically evaluate the state-of-the-art research and developments in urine-fed MFCs over the past decade (2008-2018) in terms of their construction (material selection and configuration), modes of operation (batch, continuous, cascade, etc.) and performance (power generation, nutrient recovery and waste treatment). This review identifies the preference for sources of urine for MFC application from human beings, cows and elephants. Among these, human urine-fed MFCs offer a variety of applications to practice in the real-world scenario. One key observation is that, effective disinfection can be achieved by optimizing the operating conditions and MFC configurations without compromising on performance. In essence, this review demarcates the scope of enhancing the reuse potential of urine for renewable energy generation and simultaneously achieving resource recovery.

Sign in / Sign up

Export Citation Format

Share Document