scholarly journals Taylor-Couette Column for Emulsion Liquid Membrane System: Characterisation Study

2019 ◽  
Vol 8 (1) ◽  
pp. 22-27 ◽  
Author(s):  
Adhi Kusumastuti ◽  
Samsudin Anis ◽  
Gunawan Muhammad Najibulloh
Keyword(s):  
Shear Stress ◽  
Flow Regime ◽  
Liquid Membrane ◽  
Volume Ratio ◽  
Membrane System ◽  
Extraction Process ◽  
Fluid Viscosity ◽  
Emulsion Liquid Membrane ◽  
Distribution Volume Ratio ◽  
Taylor Couette

Study on the application of Taylor-Couette column for emulsion liquid membrane system has been done. To optimise extraction process under TCC, a research to investigate effect of viscosity and cylinders rotation is of important. Fluid viscosity was examined by varying volume ratio of kerosene to water. TCC was characterised to determine flow regimes, shear stress, and energy loss distribution. Volume ratio of oil to water was varied at 1:1, 1:3, 1:5, and 1:6 while inner and outer cylinders speed were maintained constant at 300 and 200 rpm, respectively. Investigation on the effect of volume ratio of oil to water towards flow regime ended to same flow regime of Featureless Turbulent. There was degradation of wall shear stress from 8.57x10-2 Pa to 7.42x10-2 Pa.

ENHANCING TEXTILE DYE REMOVAL IN EMULSION LIQUID MEMBRANE SYSTEM USING TAYLOR COUETTE COLUMN

2018 ◽  
Vol 80 (3) ◽  
Author(s):  
Adhi Kusumastuti ◽  
A. L. Ahmad ◽  
Rodia Syamwil ◽  
Samsudin Anis
Keyword(s):  
Methylene Blue ◽  
Liquid Membrane ◽  
Volume Ratio ◽  
Interfacial Area ◽  
Membrane System ◽  
Textile Dye ◽  
Feed Concentration ◽  
Emulsion Liquid Membrane ◽  
Low Concentration ◽  
Taylor Couette

Although textile dyes is basically available in very low concentration (10-200 ppm); it should be removed due to the toxicity to human body and environment. Among the existing methods, emulsion liquid membrane (ELM) is a promising method by providing high interfacial area and the ability to remove a very low concentration of the solute. The optimal emulsions were produced using commercially supplied homogeniser. Initially, methylene blue in simulated wastewater was extracted using a Taylor-Couette column. Methylene blue concentration was determined using spectrophotometer. Complete extraction was performed in the designed column. The research obtained optimal extraction efficiency of about 99% at external phase pH of 10, carrier concentration of 9 wt. %, HCl concentration of 0.5 M, initial feed concentration of 20 ppm, volume ratio of emulsion to feed phase of 1:5, extraction time of 5 min, and extraction speed of 600 rpm. 

scholarly journals Emulsion Liquid Membrane for Cadmium Removal: Experimental Results and Model Prediction

2013 ◽  
Vol 65 (4) ◽  
Author(s):  
A. L. Ahmad ◽  
Adhi Kusumastuti ◽  
M. M. H. Shah Buddin ◽  
D. C. J. Derek ◽  
B. S. Ooi
Keyword(s):  
Mass Transfer ◽  
Model Prediction ◽  
Liquid Membrane ◽  
Volume Ratio ◽  
Membrane System ◽  
Extraction Process ◽  
Transfer Model ◽  
Emulsion Liquid Membrane ◽  
Cadmium Removal ◽  
External Phase

A study on mass transfer model for cadmium extraction in emulsion liquid membrane system has been done. Mass transfer in the external phase and emulsion globule, stripping reaction, and diffusion of the complex were taken account into the model. Reaction and chemical equilibrium of the process were also considered. The partial differential equation was numerically solved using MATLAB software. Effect of some parameters such as acid concentration in the external phase, extraction speed, volume ratio of emulsion to feed phase, volume ratio of internal to membrane phase, and initial concentration to the extraction process were investigated and compared to the model. The model prediction can agree very well with the concentration profile of cadmium in each phase.

Carrier Assisted Emulsion Liquid Membrane Process for Recovery of Basic Dye from Wastewater using Continuous Extractor

2014 ◽  
Vol 67 (2) ◽  
Author(s):  
Norasikin Othman ◽  
Ooi Zing-Yi ◽  
Norlisa Harruddin ◽  
Raja Norimie ◽  
Norela Jusoh ◽  
...  
Keyword(s):  
Textile Industry ◽  
Liquid Membrane ◽  
Volume Ratio ◽  
Extraction Process ◽  
Membrane Phase ◽  
Emulsion Liquid Membrane ◽  
Sorbitan Monooleate ◽  
Internal Phase ◽  
Span 80 ◽  
Dye Extraction

Nowadays, water pollution has become major issue especially dye contaminated wastewaters from the textile industry. Dye causes serious environmental pollution and health problems. The removal of color from dye-contaminated wastewaters in the related industries becomes a major concern all over the world. In this research, several parameters of dye extraction and recovery in the continuous emulsion liquid membrane (ELM) process were investigated. This process consisted of three phases which are external (feed) phase, membrane phase and internal phase. The membrane phase was prepared by dissolving extractant bis(2-ethylhexyl)phosphoric acid (D2EHPA) and hydrophobic surfactant sorbitan monooleate (Span 80) in kerosene as diluents. The internal phase consisted of an aqueous solution of sulfuric acid (H2SO4). The important parameters governing the extraction process of dye such as stirring speed, initial dye concentration, Span 80 concentration and treat ratio (volume ratio of emulsion to external phase) were studied. The results showed that the optimum condition for 25ppm initial concentration of dye extraction are 250 rpm stirring speed, 5% (w/v) Span 80 and treat ratio 1:5. At this condition, the percentage of dye extraction, stripping and recovery were 98%, 82% and 81% respectively. Hence, continuous ELM technique is proven to be a very promising technique in industrial wastewater treatment and recovery of dye.

Separation of Ni(II) from Nickel-Containing Wastewater in an Emulsion Liquid Membrane System with P507 as Carrier

2011 ◽  
Vol 233-235 ◽  
pp. 837-840 ◽  
Author(s):  
Bo Quan Jiang ◽  
Jiang Nan Zeng ◽  
Yu De Liu ◽  
Wen Long Zhang
Keyword(s):  
Aqueous Phase ◽  
Liquid Membrane ◽  
Volume Fraction ◽  
Volume Ratio ◽  
Membrane System ◽  
Optimal Operation ◽  
Emulsion Liquid Membrane ◽  
Nickel Ions ◽  
Operation Conditions ◽  
Span 80

An effective emulsion liquid membrane system with P507 as carrier, Span-80 as surfactant and H2SO4 as internal aqueous phase was established to treat Ni(Ⅱ)-containing wastewater. The effects of volume fraction of Span-80 in the oil phase(φ(Span-80)), emulsifying stirring speed(ν1), separation stirring speed(ν2), volume fraction of P507(φ(P507)), volume ratio of oil phase to internal phase(Roi), milk phase to water phase(Rew) and concentration of H2SO4 in internal aqueous phase on Ni(Ⅱ) migrating rate have been investigated in the course of migrating of nickel ions in the system. The optimal operation conditions were determined to be: φ(Span-80)=8.5%,ν1 =3600 r·min-1,ν2 =320 r·min-1, φ(P507)=6.5%, Roi =1:1, Rew =2:5 and c（H2SO4）=1.6 mol·L-1 ,under which the migrating rate of nickel ions reached above 97%.

Removal of Phenol by a New Emulsion Liquid Membrane System and its Heat-Induced Demulsification

2011 ◽  
Vol 356-360 ◽  
pp. 1675-1678 ◽  
Author(s):  
Wei Peng ◽  
Chun Jian Xu
Keyword(s):  
Aqueous Solution ◽  
Liquid Membrane ◽  
Ph Value ◽  
Volume Ratio ◽  
Membrane System ◽  
Membrane Phase ◽  
Emulsion Liquid Membrane ◽  
Internal Phase ◽  
External Phase ◽  
Demulsification Efficiency

Removal of phenol from aqueous solution by a new emulsion liquid membrane (ELM) system and its heat-induced demulsification have been investigated. The ELM consists of commercial kerosene as organic solvent, OP-4 as surfactant agent, hydrochloric acid as the stripping phase. Effect of different operating parameters such as internal phase concentration, surfactant concentration, stirring speed, PH value in external phase, volume ratio of membrane phase to internal phase and volume ratio of membrane phase to external phase were investigated for the removal of phenol from aqueous solution. At the optimum condition about 95.7% phenol is removed in less than 20min of contact time. The demulsification efficiency was investigated under different temperature and time and proved to be high at 80°C.

scholarly journals Flow regime analysis of Taylor-Couette column for emulsion liquid membrane applications

2019 ◽  
Author(s):  
Adhi Kusumastuti ◽  
Gunawan Muhammad Najibulloh ◽  
Nur Qudus ◽  
Samsudin Anis
Keyword(s):  
Flow Regime ◽  
Liquid Membrane ◽  
Emulsion Liquid Membrane ◽  
Taylor Couette ◽  
Regime Analysis

scholarly journals Study of Copper Recovery Using Emulsion Liquid Membrane under Taylor-Couette Column

2019 ◽  
Author(s):  
Adhi Kusumastuti ◽  
Widi Astuti ◽  
Nur Qudus
Keyword(s):  
Liquid Membrane ◽  
Volume Ratio ◽  
Textile Wastewater ◽  
Copper Recovery ◽  
Emulsion Liquid Membrane ◽  
Phase Concentration ◽  
Internal Phase ◽  
Feed Phase ◽  
Taylor Couette ◽  
Home Industries

High demand on batik fabric significantly increased wastewater volume from batik home industries. Copper, being used as mordanting agent, available in the highest concentration in industrial textile wastewater. Emulsion liquid membrane (ELM) is promising selective method to recover solute. Taylor-Couette column (TCC) was proposedtoextractcopperinsteadofusingconventionalreactorthatdisturbsemulsion stability. Experiment was done by varying volume ratio of emulsion to feed phase, carrier and internal phase concentration. Extraction efficiency of>98% was obtained at volume ratio of emulsion to feed phase of 1:5, carrier concentration of 4 wt. %, and internal phase concentration of 0.1 M, respectively

CADMIUM REMOVAL USING VEGETABLE OIL BASED EMULSION LIQUID MEMBRANE (ELM): MEMBRANE BREAKAGE INVESTIGATION

2015 ◽  
Vol 75 (1) ◽  
Author(s):  
A. L. Ahmad ◽  
M. M. H. Shah Buddin ◽  
B. S. Ooi ◽  
Adhi Kusumastuti
Keyword(s):  
Vegetable Oil ◽  
Liquid Membrane ◽  
Corn Oil ◽  
Volume Ratio ◽  
Aliquat 336 ◽  
Emulsion Liquid Membrane ◽  
Cadmium Removal ◽  
Internal Phase ◽  
External Phase ◽  
Span 80

The aim of this research is to quantify the occurrence of membrane breakage in vegetable oil based Emulsion Liquid Membrane (ELM). Basically, ELM consists of three main phases; internal, external and membrane. In this work, the membrane phase was prepared by dissolving Span 80 as surfactant and Aliquat 336 as carrier in commercial grade corn oil. As a way to promote sustainable development, vegetable oil which is environmentally benign diluent was incorporated in the formulation of ELM. The influence of several important parameters towards membrane breakage were studied. They are carrier and surfactant concentration, W/O volume ratio, emulsification time, internal phase concentration as well as stirring speed. Based on the data obtained, emulsion prepared using 4 wt% Aliquat 336 and 3 wt% Span 80 resulted in the most stable emulsion with only 0.05% membrane breakage. The emulsion was produced using W/O volume ratio of 1/3 and it was homogenized with the assistance of ultrasound for 15 min. Moreover, emulsion produced able to provide a fair balance between emulsion stability and Cd(II) permeability as it able to remove 98.20% Cd(II) ions from the external phase. 

scholarly journals Emulsion Liquid Membrane Extraction of Turquoise Blue Reactive Dye–Study on Membrane Breakage and Swelling

2017 ◽  
Vol 11 (1) ◽  
Author(s):  
N. Othman ◽  
S. N. Zailani ◽  
N. Mili
Keyword(s):  
Liquid Membrane ◽  
Raw Materials ◽  
Extraction Process ◽  
Reactive Dye ◽  
Point Of View ◽  
Membrane Extraction ◽  
Hydrodynamic Condition ◽  
Emulsion Liquid Membrane ◽  
Liquid Membrane Extraction ◽  
Span 80

Reactive dyes are the principal dyes used in batik industry in Malaysia. From the environmental point of view the dyes should be removed from wastewater because they are toxic in nature. Therefore, the removal and recovery of dyes from batik industry wastewater is absolute necessity in order to save raw materials and to protect environment from hazardous compounds. An experiment was carried out using emulsion liquid membrane (ELM) process in batch system to study the extraction behaviour of Turquoise Blue which is commonly used in batik industry. Several parameters have been studied such as carrier and surfactant/emulsifier concentrations, stripping agent and extraction time. The liquid membrane was formulated using kerosene as diluent, SPAN 80 as emulsifier and tri-dodecylamine (TDA) as a carrier. Hydrodynamic condition to generate extraction process was at 1:3 treat ratio and 250 rpm stirring speed for 10 minutes while the emulsification was done at 12000 rpm for 5 minutes using homogenizer. The result obtained shows that, more than 70% of Turquoise Blue was extracted at favourable condition of 0.07 M TDA, 7% (w/v) SPAN 80 and 0.5 M Thiourea in 1 M NaOH.

Sign in / Sign up

Export Citation Format

Share Document