scholarly journals Performance analysis of four plant fiber/polyvinyl chloride composites under two degradation conditions with water or seawater with xenon lamp

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 4672-4688
Author(s):  
Xinyu Zhong ◽  
Yaowen Zhu ◽  
Shuaijun Liu ◽  
Jingjing Fu ◽  
Hong Lin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Polyvinyl Chloride ◽  
Xenon Lamp ◽  
Internal Defects ◽  
Plant Fibers ◽  
Wood Plastic Composites ◽  
Plastic Composites ◽  
Plastic Matrix

To explore the properties of wood-plastic composites (WPCs) used in maritime climates, four different plant fibers (bamboo, rice straw, wheat straw, reed straw), and polyvinyl chloride (PVC) were used to prepare WPCs through extrusion. The composites were subjected to either seawater immersion + xenon lamp aging or deionized water spray + xenon lamp aging. The mechanical properties (tensile strength, flexural strength, impact strength), color change, and water absorption performance were analyzed. The plant fibers were analyzed by X-ray diffraction and Fourier transform infrared spectroscopy (FTIR), and the microstructures of the surfaces were observed by scanning electron microscopy (SEM). The reed fiber had the highest crystallinity; reed/PVC composites had good interface with the plastic matrix, less internal defects, and the best comprehensive performance, with a tensile strength, bending strength, and impact strength of 25.4 MPa, 34.4 MPa, and 4.30 KJ·m-2, respectively. The simulated seawater immersion + xenon lamp aging reduced the performance of wood-plastic composites, destroyed the quality of the combination of plant fibers and plastic matrix, and created internal defects. The comprehensive mechanical properties of reed/PVC composites were the best. The properties of bamboo/PVC composites decreased the least, with a decrease of less than 41.2%.

Effects of the Size of Wood Flour on Mechanical Properties of Wood-Plastic Composites

2011 ◽  
Vol 393-395 ◽  
pp. 76-79 ◽  
Author(s):  
Hai Bing Huang ◽  
Hu Hu Du ◽  
Wei Hong Wang ◽  
Hai Gang Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Wood Flour ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Inorganic Filler ◽  
Full Potential ◽  
Wood Plastic Composites ◽  
Plastic Composites

In this article, wood-plastic composites(WPCs) were manufactured with wood flour(80～120mesh、40～80mesh、20～40mesh、10～20mesh) combing with high density polyethylene(HDPE). Effects of the size of wood flour on mechanical properies and density of composites were investigated. Results showed that particle size of wood flour had an important effect on properitiesof WPCs. Change of mesh number had a outstanding effect on flexural modulus, tensile modulus and impact strength, howere, little effect on flexural strength and tensile strength. When mesh number of wood flour changed from 80～120mesh to 10～20mesh,flexural modulus and tensile modulus were respectively enhanced by 42.4% and 28.4%, respectively, and impact strength was decreased by 35.5%.Size of wood flour basically had no effect on density of composite within 10～120mesh. The use of wood flour or fiber as fillers and reinforcements in thermoplastics has been gaining acceptance in commodity plastics applications in the past few years. WPCs are currently experiencing a dramatic increase in use. Most of them are used to produce window/door profiles,decking,railing,ang siding. Wood thermoplastic composites are manufactured by dispering wood fiber or wood flour(WF) into molten plastics to form composite materials by processing techniques such as extrusion,themoforming, and compression or injection molding[1]. WPCs have such advantages[2]：(1)With wood as filler can improve heat resistance and strength of plastic, and wood has a low cost, comparing with inorganic filler, wood has a low density. Wood as strengthen material has a great potential in improving tensile strength and flexural modulus[3]；(2) For composite of same volume, composites with wood as filler have a little abrasion for equipment and can be regenerated；(3)They have a low water absorption and low hygroscopic property, They are not in need of protective waterproof paint, at the same time, composite can be dyed and painted for them own needs；(4)They are superior to wood in resistantnce to crack、leaf mold and termite aspects, composites are the same biodegradation as wood；(5)They can be processed or connected like wood；（6）They can be processed into a lots of complicated shape product by means of extrusion or molding and so on, meanwhile, they have high-efficiency raw material conversion and itself recycle utilization[4]. While there are many sucesses to report in WPCs, there are still some issues that need to be addressed before this technology will reach its full potential. This technology involves two different types of materials: one hygroscopic(biomass) and one hydrophobic(plastic), so there are issues of phase separation and compatibilization[5]. In this paper, Effects of the size of wood powder on mechanical properties of WPCs were studied.

Influence of active inorganic fillers on the physical and mechanical properties of polyvinyl chloride wood-plastic composites when immersed

BioResources ◽  
2020 ◽  
Vol 16 (1) ◽  
pp. 789-804
Author(s):  
Qiang Jin ◽  
Lin Zhu ◽  
Jiedeerbieke Madiniyeti ◽  
Chunxia He ◽  
Li Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Absorption ◽  
Polyvinyl Chloride ◽  
Steel Slag ◽  
Physical And Mechanical Properties ◽  
Control Group ◽  
Wood Plastic Composites ◽  
Plastic Composites ◽  
Inorganic Fillers

Hydration-active steel slag and slag micropowder were used as inorganic fillers with silane coupling agent (KH550) to prepare wheat straw/polyvinyl chloride wood-plastic composites (WPCs) by extrusion molding. A 35-day immersion and a pre-immersion test were carried out to analyze the influence of steel slag and slag micropowder on the physical and mechanical properties of the WPCs under wet conditions. Results showed the following: (1) KH-550 exhibited a good surface modification effect on the activated steel slag and slag micropowder, (2) an increase in the activated steel slag and slag micropowder content could effectively reduce the percent water absorption of the WPCs by 20% to 25% and the expansion by 20% to 24%, respectively, compared with the control group, but had a limited effect on the tensile strength retention, and (3) pre-immersion could effectively induce the synergistic reinforcement effect of the active fillers, resulting in reaching the saturated water absorption within 20 days. The water absorption and tensile strength were respectively 18% to 25% lower and 1.5% to 3% higher than those of the composites without pre-immersion. The results of this study could provide experimental data and theoretical references for the influence of hydration-active inorganic fillers on WPC properties.

Study on Application of Modified Polyethylene in Preparation of Wood-Plastic Composites

2010 ◽  
Vol 150-151 ◽  
pp. 379-385
Author(s):  
Qun Lü ◽  
Qing Feng Zhang ◽  
Hai Ke Feng ◽  
Guo Qiao Lai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
High Density Polyethylene ◽  
Wood Flour ◽  
Wood Plastic Composites ◽  
Plastic Composites ◽  
The Matrix ◽  
The Impact

The wood-plastic composites (WPC) were prepared via compress molding by using the blends of high density polyethylene (HDPE) and modified polyethylene (MAPE) as the matrix and wood flour (WF) as filler. The effect of MAPE content in the matrix on the mechanical properties of the matrix and WPC was investigated. It was shown that the change of MAPE content in the matrix had no influence on the tensile strength of the matrix, but markedly reduced the impact strength of the matrix. Additionally, it had significant influence on the strength of WPC. When the content of wood flour and the content of the matrix remained fixed, with increasing the content of MAPE in the matrix, the tensile strength and the flexural strength of WPC tended to increase rapidly initially and then become steady. Moreover, with the increasing of MAPE concentration, the impact strength of WPC decreased when the low content of wood flour (30%) was filled, but increased at high wood flour loading (70%).

Mechanical Properties of 3D-Printed Wood-Plastic Composites

2018 ◽  
Vol 777 ◽  
pp. 499-507 ◽  
Author(s):  
Ossi Martikka ◽  
Timo Kärki ◽  
Qing Ling Wu
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
3D Printed

3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

Mechanical Properties of Acrylate-Styrene-Acrylonitrile/Bagasse Composites

2013 ◽  
Vol 747 ◽  
pp. 355-358 ◽  
Author(s):  
Pornsri Pakeyangkoon ◽  
Benjawan Ploydee
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
Roll Mill ◽  
The Matrix ◽  
Styrene Acrylonitrile

Mechanical properties of wood plastic composite, prepared from acrylate-styrene-acrylonitrile (ASA) and bagasse, were investigated. In this study, 10 to 50 phr of bagasse were used in order to obtain the wood plastic composite with superior mechanical properties. The wood plastic composites in the study were prepared by melt-blending technique. All materials were mixed by using a two-roll-mill, shaped into sheets by a compression molding machine and the specimens were cut with a cutting machine. Youngs modulus, flexural strength, flexural modulus, impact strength and hardness of the wood plastic composites were investigated and found to improve with increasing bagasse content. However, some composite properties, i.e., impact strength, was decreased by adding the bagasse and then become steady when the amount of bagasse added was more than 30 phr. It was concluded that wood plastic composites with the desirable mechanical properties can be formulated using ASA as the matrix polymer and 50 phr of bagasse.

Study of Wood Plastic Composites on Mechanical and Thermal Properties after Immersed into Water

2014 ◽  
Vol 1004-1005 ◽  
pp. 497-500
Author(s):  
Wang Wang Yu ◽  
Dong Xue
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
High Density Polyethylene ◽  
Nucleating Agent ◽  
Mechanical And Thermal Properties ◽  
Wood Plastic Composites ◽  
Plastic Composites ◽  
Before And After ◽  
Negative Effect

In this study, silvergrass (SV) reinforced high density polyethylene (HDPE) composites were prepared. The effects of slivergrass fibers (SV) content on the mechanical properties, crystalline properties of wood plastic composites (WPCs) before and after water absorption were investigated. It was found that compared with the untreated WPCs after immersed into water, the tensile strength of PMDI treated composites were higher. Silvergrass can be the nucleating agent with treated by PMDI. The Xc of PMDI treated WPCs after immersed into water was also increased. However, this improved Xc has negative effect on mechanical properties.

scholarly journals Influence of fibre and matrix characteristics on properties and durability of wood–plastic composites in outdoor applications

2018 ◽  
Vol 33 (4) ◽  
pp. 477-500 ◽  
Author(s):  
Jose Vercher ◽  
Vicent Fombuena ◽  
Arturo Diaz ◽  
Maria Soriano
Keyword(s):  
Mechanical Properties ◽  
Polyvinyl Chloride ◽  
Rice Husk ◽  
Environmental Issues ◽  
Wood Plastic Composites ◽  
Ageing Behaviour ◽  
General Terms ◽  
Plastic Composites ◽  
Chemical Agents ◽  
Recycled Plastics

The awareness of society on environmental issues has increased in recent years. This article focuses on the wood–plastic composites (WPCs), obtained from recycled plastics and natural fibres waste, and their application in architecture. In order to give some recommendations to architects regarding the choice of a WPC as an alternative to wood for uses in outdoor decking, a series of standardized physical, mechanical and chemical tests have been carried out on two commercial WPC materials: one with a polyvinyl chloride (PVC) – PVC matrix and rice husk filler and a second one with a polyethylene (PE) – PE matrix and pine wood reinforcement. Mechanical, thermal and ageing behaviour of these commercial WPC has been broadly studied. This research provides value information to find out which WPC material best support durability aspects, those that most concern in an architectural application of outdoor decking. In general terms, WPC developed by PVC matrix and rice husk as filler shown greater physical–mechanical properties, better resistance to chemical agents and greater resistance to ageing behaviour and changes in visual aspect.

Effects of PMDI Modified on Physico-Mechanical Properties of Silvergrass Reinforced High Density Polyethylene Composites

2013 ◽  
Vol 750-752 ◽  
pp. 38-42
Author(s):  
Wang Wang Yu ◽  
Juan Li ◽  
Yun Ping Cao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Water Absorption ◽  
High Density Polyethylene ◽  
High Density ◽  
Hydroxyl Groups ◽  
Wood Plastic Composites ◽  
Plastic Composites ◽  
Methylene Diphenyl Diisocyanate

In this study, the silvergrass (SV) was used to reinforce HDPE composites. The effects of polymeric methylene diphenyl diisocyanate (PMDI) content, slivergrass fibers content on the mechanical, water absortion of wood plastic composites (WPCs) were investigated. It was found that the mechanical properties of the SV reinforced HDPE composites can be improved by PMDI treatment. The highest tensile strength and flexural strength of the composites can be reached with 50% SV contents at the SV: PMDI=6:1. It has been proved that the hydroxyl groups of SV fibers which can react with the-NCO by FTIR. It also can be concluded that the water absorption of PMDI treated WPCs was lower than untreated ones.

scholarly journals Accelerated weathering of polyvinyl chloride-based wood-plastic composites: Effect of plant species

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5261-5271
Author(s):  
Ruige Qi ◽  
Chunxia He ◽  
Qiang Jin
Keyword(s):  
Polyvinyl Chloride ◽  
Plant Species ◽  
Color Change ◽  
Accelerated Weathering ◽  
Plant Fibers ◽  
Wood Plastic Composites ◽  
Bonding Performance ◽  
Plastic Composites ◽  
The Impact ◽  
Selection Of

The effect of plant species on the accelerated weathering behaviors of polyvinyl chloride-based wood-plastic composites (WPCs) was studied. The selected plant species were eucalyptus, rice husk, and bamboo. The color and chemical compositional changes that occurred due to accelerated weathering were monitored using colorimetry and Fourier transform infrared spectroscopy. The lignin and carbonyl contents of the WPCs were altered with exposure. The color change and lightness of the weathered WPCs increased with exposure time, and the degree of increase depended on the plant species. The water absorption and swelling ratio of the WPCs increased with an increase in exposure. The eucalyptus-based composite was the highest ranked in terms of mechanical properties, and the microstructure of the impact section showed that the interfacial bonding performance deteriorated after exposure. In conclusion, the selection of plant fibers is critical to the service performance of WPCs.

Manufacturing Technique and Mechanical Property Evaluations of Polypropylene/Short Coir/Short Glass Fiber Wood Plastic Composites

2014 ◽  
Vol 910 ◽  
pp. 246-249
Author(s):  
Jia Horng Lin ◽  
Zheng Lan Lin ◽  
Jin Mao Chen ◽  
Cha Chi Fan ◽  
Ching Wen Lou
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Interfacial Adhesion ◽  
Strength Test ◽  
Plastic Composites ◽  
Short Glass Fiber ◽  
Izod Impact ◽  
Short Glass

This study uses a single screw extruder to make short coir (SC), an agricultural waste, high-strength short glass fiber (SGF), and polypropylene (PP) into pellets, which are then made into wood plastic composites (WPC) on an injection machine. During the process, maleic anhydride grafted polypropylene (PP-g-MA) is used as a coupling agent to improve the interfacial adhesion between coir and PP as well as between SGF and PP. A tensile strength test, flexural strength test, and Izod impact strength test are performed on the samples to examine the mechanical properties. The experiment results show that when the content of SGF increases from 3 wt% to 12 wt%, the tensile strength increases from 26.08 MPa to 36.68 MPa, and flexural strength increases from 36.01 MPa to 49.91 MPa, but the Izod impact strength decreases from 286.16 J/m to 218.14 J/m. In addition, the addition of 2 wt% of PP-g-MA improves the interfacial adhesion between matrices (PP) and reinforcement (SC or SGF), thereby fortifying the mechanical properties of the composites.

Sign in / Sign up

Export Citation Format

Share Document