Grain size of MgO and polymorphic phases of ZrO2 in zirconia-toughened MgO

1993 ◽  
Vol 8 (11) ◽  
pp. 2757-2760 ◽  
Author(s):  
Yasuro Ikuma ◽  
Toshio Sugiyama ◽  
Junko Okano

Zirconia-toughened MgO was manufactured and examined by scanning and transmission electron microscopes. It was found that ZrO2 particles that are present on the MgO grain boundary limit the grain growth of MgO. The cooling rate has an effect on the ZrO2 phase in zirconia-toughened MgO fired in a cubic ZrO2–MgO field, but it does not have an effect on the ZrO2 phase in specimens fired in a tetragonal ZrO2–MgO field. Tetragonal ZrO2 was retained at room temperature in zirconia-toughened MgO.

Author(s):  
Yung-Jen Lin ◽  
Peter Angelini ◽  
Martha L. Mecartney

Yttria stabilized zirconia is a versatile ceramic material. It can be used for structural components or as a solid electrolyte. Its properties (such as high toughness) are strongly affected by the microstructure. In partially stabilized zirconia, the high toughness is mainly due to the toughening effect of a tetragonal (t) to monoclinic (m) phase transformation in the vicinity of a crack. Retention of tetragonal zirconia at room temperature is important for fabricating transformation toughened materials. To completely retain tetragonal zirconia at room temperature the grain size of the material must be less than a critical size. In yttria stabilized zirconia this critical grain size depends on the yttria concentration. Grain growth of yttria stabilized zirconia is also influenced by the amount of yttria in the grains. These previous studies, however, have focused on the behavior of materials with minimal glassy grain boundary phases. In contrast, in commercial polycrystalline zirconia often a significant amount of glassy grain boundary phase is present. This current research seeks to elucidate the effects of these grain boundary phases on the grain growth in yttria stabilized zirconia ceramics.


2007 ◽  
Vol 551-552 ◽  
pp. 387-392 ◽  
Author(s):  
Wen Juan Zhao ◽  
Hua Ding ◽  
D. Song ◽  
F.R. Cao ◽  
Hong Liang Hou

In this study, superplastic tensile tests were carried out for Ti-6Al-4V alloy using different initial grain sizes (2.6 μm, 6.5μm and 16.2 μm) at a temperature of 920°C with an initial strain rate of 1×10-3 s-1. To get an insight into the effect of grain size on the superplastic deformation mechanisms, the microstructures of deformed alloy were investigated by using an optical microscope and transmission electron microscope (TEM). The results indicate that there is dramatic difference in the superplastic deformation mode of fine and coarse grained Ti-6Al-4V alloy. Meanwhile, grain growth induced by superplastic deformation has also been clearly observed during deformation process, and the grain growth model including the static and strain induced part during superplastic deformation was utilized to analyze the data of Ti-6Al-4V alloy.


2021 ◽  
Author(s):  
Rahul Kumar Kushwaha ◽  
Ambresh Mallya ◽  
Dipen Sahu ◽  
Jaya Krishna Meka ◽  
Sheng-Lung Chou ◽  
...  

<p>Benzene (C<sub>6</sub>H<sub>6</sub>) ice has been observed in the Titan’s stratosphere [1], and benzonitrile (C<sub>6</sub>H<sub>5</sub>CN) is a possible constituent in the benzene and nitrogen-rich environment of Titan’s atmosphere [2]. The energetic processing of such aromatic molecules can synthesize large and complex aromatic molecules such as the Polycyclic Aromatic Hydrocarbons (PAHs). To-date a number of laboratory experiments have reported the formation of complex organics from the energetic processing of aromatic molecules [3-6]. In particular, Scanning Electron Microscopy (SEM) micrographs of the residues resulting from irradiated benzene ices are found to contain geometrically shaped particles [6]. Therefore, by employing electron microscopes, we can understand the physical nature of the dust leftover from the aromatic molecule irradiation.</p> <p>In the present investigation, we subjected benzonitrile ice made at 4 K to vacuum ultraviolet (9 eV) radiation at two beamlines, BL03 and BL21A2 of Taiwan Light Source at NSRRC, Taiwan. After irradiation, the ice was warmed to room temperature, which left a brownish residue on the Potassium Bromide (KBr) substrate. The VUV spectrum of the residue is observed to have characteristic aromatic signatures. The residue is then transferred to a quantifoil grid for High-Resolution Transmission Electron Microscope (HR- TEM) imaging. HR-TEM micrographs revealed the presence of graphene in the residue. This result suggests that N-graphene could be present in benzene and nitrogen-rich icy clouds of Titan. The high masses observed by the Cassini plasma spectrometer in Titan’s atmosphere could then be attributed to the presence of N-graphene along with the more common tholins [7].</p> <p><strong>References</strong></p> <p>[1] Vinatier S. et al. (2018) <em>Icarus, 310,</em> 89.</p> <p>[2] Loison J. C. et al. (2019) <em>Icarus 329,</em> 55.</p> <p>[3] Strazzulla G. et al. (1991) <em>A&A, 241</em>, 310.</p> <p>[4] Callahan M. P. et al. (2013) <em>Icarus, 226</em>, 1201.</p> <p>[5] James R. et al. (2019) <em>RSC Adv. 9</em> (10), 5453.</p> <p>[6] Rahul K. K. et al. (2020) <em>Spectrochim. Acta A, 231, </em>117797.</p> <p>[7] Rahul K. K. et al. (2020) <em>arXiv:2008.10011</em>.</p>


1996 ◽  
Vol 436 ◽  
Author(s):  
R.-M. Keller ◽  
W. Sigle ◽  
S. P. Baker ◽  
O. Kraft ◽  
E. Arzt

AbstractIn-situ transmission electron microscopy (TEM) was performed to study grain growth and dislocation motion during temperature cycles of Cu films with and without a cap layer. In addition, the substrate curvature method was employed to determine the corresponding stresstemperature curves from room temperature up to 600°C. The results of the in-situ TEM investigations provide insight into the microstructural evolution which occurs during the stress measurements. Grain growth occurred continuously throughout the first heating cycle in both cases. The evolution of dislocation structure observed in TEM supports an explanation of the stress evolution in both capped and uncapped films in terms of dislocation effects.


1991 ◽  
Vol 238 ◽  
Author(s):  
A. M. El-Sherik ◽  
K. Boylan ◽  
U. Erb ◽  
G. Palumbo ◽  
K. T. Aust

ABSTRACTThe thermal stability of electrodeposited nanocrystalline Ni-1.2%P and Ni-0.12%S alloys is evaluated by in-situ electron microscopy studies. Isothermal grain size versus annealing time curves at 573K and 623K show an unexpected thermal stabilization in form of a transition from rapid initial grain growth to negligible grain growth. This behaviour is discussed in terms of the various grain boundary drag mechanisms which may be operative in these alloys.


2016 ◽  
Vol 724 ◽  
pp. 8-11
Author(s):  
Chun Yu Teng ◽  
Yun Fu ◽  
Zhan Yong Ren ◽  
Yong Hong Li ◽  
Yun Wang ◽  
...  

The properties of alloys depend on its microstructure, such as the size of grains. In general, the balanced mechanical properties of alloys can be obtained with small grain size. While the grain size of alloys may increases under heat treatment, thermal mechanical processing and service condition of high temperature, i.e., the grain growth is inevitable. The effort of most research is to control the rate of grain growth and avoid abnormal grain growth. For example, pinning the grain boundary and reduce its mobility with the second phase particles in order to prevent grain growth. Therefore, the properties of the alloys will not decreases dramatically and the structure retains a high degree of integrity. The details of grain growth with particle pinning were investigated by phase field simulations in the present paper. It is found that, with the same size of pinning particles, the pinning effect increases with the increases of the pinning particle number. With the same pinning particle number, the pinning effect increases with the increases of pinning particle size. Under the same total volume of pinning particles while different particle size and number, the pinning effect is complicated and it will be discussed in details. The pinning effect decreases with the increases of grain boundary energy. These findings could shed light on the understanding of the grain growth kinetics with particle pinning.


1986 ◽  
Vol 81 ◽  
Author(s):  
M. A. Crimp ◽  
K. M. Vedula ◽  
D. J. Gaydosh

AbstractIt has been shown that it is possible to obtain significant room temperature tensile ductility in FeAl alloys using iron-rich deviations from stoichiometry. A comparison of the room temperature tensile and compressive behaviors of Fe−50at% Al and Fe−40at% Al shows that FeAl is brittle at higher Al contents because it fractures along grain boundaries before general yielding. Lower aluminium contents reduce the yield stress substantially and hence some ductility is observed before fracture.Addition of boron results in measurable improvements in ductility of Fe−40at% Al and is accompanied by an increase in transgranular tearing on the fracture surface, suggesting a grain boundary strengthening mechanism.Increasing the cooling rate following annealing at 1273 K results in a large increase in the yield strength and a corresponding decrease in ductility.


2006 ◽  
Vol 976 ◽  
Author(s):  
Bryan Miller ◽  
Jamey Fenske ◽  
Dong Su ◽  
Chung-Ming Li ◽  
Lisa Dougherty ◽  
...  

AbstractDeformation experiments at temperatures between 300 and 750 K have been performed in situ in the transmission electron microscope to investigate dislocation interactions and reactions with grain boundaries and other obstacles. Dislocations, both partial and perfect, as well as deformation twins have been observed being emitted from grain boundaries and, in some cases, even the same grain boundary. The ejection of dislocations from the grain boundary can result in its partial or total annihilation. In the latter case, the disintegration of the grain boundary was accompanied by grain growth and a change in misorientation.


2019 ◽  
Vol 58 (1) ◽  
pp. 98-106
Author(s):  
Haitao Ni ◽  
Jiang Zhu ◽  
Zhaodong Wang ◽  
Haiyang Lv ◽  
Yongyao Su ◽  
...  

Abstract This review focuses on grain growth behaviors and the underlying mechanisms of bulk electrodeposited nanocrystalline nickel and nickel-iron alloys. Effects of some important factors on grain growth are described. During thermal-induced grain growth process, grain boundary migration plays a key role. For similar thermal conditions, due to grain boundary mobility with solute drag, limited grain growth occurs in nanocrystalline alloys, as compared to pure metals. Nonetheless, in the case of stress-induced grain growth process, there are a variety of mechanisms in samples having various deformation histories. As an example the grain growth of nanocrystalline nickel and Ni-20%Fe alloy with nearly the same grain-size distribution and average grain size is compared in this paper. Thermal analysis indicates nanocrystalline nickel is much more prone to rapid grain growth than nanocrystalline Ni-20%Fe alloy. Nevertheless, grain growth of nanocrystalline Ni-20%Fe is found to be more pronounced than nanocrystalline nickel during rolling deformation.


2020 ◽  
Vol 993 ◽  
pp. 953-958
Author(s):  
Yan Wu ◽  
Ren Chuang Yan ◽  
Er Wei Qin ◽  
Wei Dong Chen

In this paper, the effect of grain boundary energy in AZ31 Mg alloy with multi-order parameters phenomenological phase field model has been discussed during the progress of recrystallization. The average grain size of the recrystallization grain at a certain temperature and a certain restored energy but various grain boundary energies have been studied, and the simulated results show that the larger the grain boundary energy is, the larger the average grain size will be, and the speed of grain growth will increase with the increase of grain boundary energy. Additionally, temperature will also increase the grain growth rate.


Sign in / Sign up

Export Citation Format

Share Document