Growth of Ultra-High Density 3C-SiC Nanowires via Single Source CVD

2011 ◽  
Vol 1350 ◽  
Author(s):  
Kasif Teker ◽  
Joseph A. Oxenham

ABSTRACTSilicon carbide (SiC) nanostructures attract interest due to their applications in optoelectronic devices, sensors, and high-power/high temperature electronics. The synthesis of SiC nanowires by chemical vapor deposition using hexamethyldisilane (HMDS) as a source material on SiO2/Si substrate has been investigated. Various catalyst materials, including iron (film and nanoparticles), nickel (film and nanoparticles), and cobalt nanoparticles have been used. The growth runs have been carried out at temperatures between 900 and 1100°C under H2 as carrier gas. 3C-SiC nanowires have successfully been grown at even lower temperatures despite the lower efficiency of source decomposition at low temperatures. The SiC nanowire diameters are in the range of 8 nm to 60 nm, as determined by transmission electron microscopy (TEM). In general, the efficiency of nanowire growth has increased with temperature except the growth on Ni film, which has occasionally resulted in SiC flowers. Higher nanowire density at high temperatures can be attributed to more efficient decomposition of the source at higher temperatures. Further, optical properties of the nanowires have been studied by Fourier transform infrared spectroscopy (FTIR). The fabricated nanowires have also been characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), and x-ray diffraction (XRD).

2009 ◽  
Vol 67 ◽  
pp. 89-94 ◽  
Author(s):  
Joydip Sengupta ◽  
Sovan Kumar Panda ◽  
Chacko Jacob

The effect of Fe and Ni catalysts on the synthesis of carbon nanotubes (CNTs) using atmospheric pressure chemical vapor deposition (APCVD) was investigated. Distribution of the catalyst particles over the Si substrate was analyzed by atomic force microscopy (AFM). Characterization by X-ray diffraction analysis (XRD), field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM) and Raman spectroscopic measurements over the grown species is reported. The study clearly shows that the catalyst strongly influences morphology and microstructure of the grown CNTs.


1995 ◽  
Vol 403 ◽  
Author(s):  
G. Bai ◽  
S. Wittenbrock ◽  
V. Ochoa ◽  
R. Villasol ◽  
C. Chiang ◽  
...  

AbstractCu has two advantages over Al for sub-quarter micron interconnect application: (1) higher conductivity and (2) improved electromigration reliability. However, Cu diffuses quickly in SiO2and Si, and must be encapsulated. Polycrystalline films of Physical Vapor Deposition (PVD) Ta, W, Mo, TiN, and Metal-Organo Chemical Vapor Deposition (MOCVD) TiN and Ti-Si-N have been evaluated as Cu diffusion barriers using electrically biased-thermal-stressing tests. Barrier effectiveness of these thin films were correlated with their physical properties from Atomic Force Microscopy (AFM), Transmission Electron Microscopy (TEM), Secondary Electron Microscopy (SEM), and Auger Electron Spectroscopy (AES) analysis. The barrier failure is dominated by “micro-defects” in the barrier film that serve as easy pathways for Cu diffusion. An ideal barrier system should be free of such micro-defects (e.g., amorphous Ti-Si-N and annealed Ta). The median-time-to-failure (MTTF) of a Ta barrier (30 nm) has been measured at different bias electrical fields and stressing temperatures, and the extrapolated MTTF of such a barrier is > 100 year at an operating condition of 200C and 0.1 MV/cm.


2020 ◽  
Vol MA2020-02 (24) ◽  
pp. 1750-1750
Author(s):  
Andrea Quintero Colmenares ◽  
Patrice Gergaud ◽  
Jean-Michel Hartmann ◽  
Vincent Delaye ◽  
Nicolas Bernier ◽  
...  

1998 ◽  
Vol 535 ◽  
Author(s):  
P. Kopperschmidt ◽  
S T. Senz ◽  
R. Scholz ◽  
G. Kästner ◽  
U. Gösele ◽  
...  

AbstractWe realized “compliant” substrates in the square centimeter range by twist-wafer bonding of an (100) GaAs handle wafer to another (100) GaAs wafer with a several nm thick epitaxially grown GaAs layer followed by an appropriate back-etch procedure. The twist angle between the two GaAs wafers was chosen between 4 and 15 degrees. The twisted layers were characterized by area scanned X-ray diffraction, optical and electron microscopy and atomic force microscopy. Occasionally we observed regions showing pinholes in the transferred thin twistbonded GaAs layer.After epitaxial deposition of 300 nm InP and InGaAs films with different degrees of mismatch on these substrates, transmission electron microscopy revealed grains which are epitaxially oriented to either the substrate or the twist-bonded layer. The grain boundaries between the twisted and untwisted grains probably collect threading dislocations, thus reducing their density in the areas free of boundaries.


2015 ◽  
Vol 821-823 ◽  
pp. 213-216
Author(s):  
S.M. Ryndya ◽  
N.I. Kargin ◽  
A.S. Gusev ◽  
E.P. Pavlova

Silicon carbide thin films were obtained on Si (100) and (111) substrates by means of vacuum laser ablation of α-SiC ceramic target. The influence of substrate temperature on composition, structure and surface morphology of experimental samples was examined using Rutherford backscattering spectrometry (RBS), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), conventional and high-resolution transmission electron microscopy (TEM/HRTEM), atomic force microscopy (AFM), selected area electron diffraction (SAED) and X-ray diffraction (XRD) methods.


2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Angela De Bonis ◽  
Agostino Galasso ◽  
Antonio Santagata ◽  
Roberto Teghil

A MgB2target has been ablated by Nd:glass laser with a pulse duration of 250 fs. The plasma produced by the laser-target interaction, showing two temporal separated emissions, has been characterized by time and space resolved optical emission spectroscopy and ICCD fast imaging. The films, deposited on silicon substrates and formed by the coalescence of particles with nanometric size, have been analyzed by scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, micro-Raman spectroscopy, and X-ray diffraction. The first steps of the films growth have been studied by Transmission Electron Microscopy. The films deposition has been studied by varying the substrate temperature from 25 to 500°C and the best results have been obtained at room temperature.


Author(s):  
S. S. Srinivasan ◽  
N. Kislov ◽  
Yu. Emirov ◽  
D. Y. Goswami ◽  
E. K. Stefanakos

Nanoparticles of Zinc Ferrite (ZnFe2O4) prepared by both wet- and dry- high-energy ball milling (HEBM), have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), atomic force microscopy (AFM), surface area and pore size distribution (BET) and wavelength-dependent diffuse reflectance and scattering turned into absorption coefficient estimation using the Kubelka-Munk theory. It was found that after 72 hours of HEBM, the particle size was decreased from 220 nm for the initial material to 16.5 nm and 9.4 nm for the wet- and dry-milled samples, respectively. The optical absorption analysis revealed that the energy gap is increased (blue shift) by 0.45 eV for wet-milled and decreased (“anomalous” red shift) by 0.15 eV for dry-milled samples of ZnFe2O4 as the particle size decreased.


2019 ◽  
Vol 29 (4) ◽  
pp. 67
Author(s):  
Barakat A. F. Kamel

In this research work, the nanoparticles of aluminum oxide were synthesized by two ways. The first way is the biological by using (Pseudomonas aeruginosa) bacteria with a rate diameter (102.35) nm. The second way is the electrochemical with a rate diameter (62) nm. These nanoparticles were characterized by Atomic Force Microscopy (AFM), X-Ray diffraction technique (XRD), Transmission Electron Microscopy (TEM) and Scanninig Electron Microscopy (SEM). Alumina nanoparticles are thermodynamically stable particles over a wide temperature range . The biological activity of these nanoparticles toward different species of pathogenic bacteria (Staphylococcus aureus ) and (Pseudo monas) has been investigated. The results stated that the nanoparticles prepared by chemical way was more effective on the inhibition of bacteria than the nanoparticles prepared by biological way


Sign in / Sign up

Export Citation Format

Share Document